• Journal of Energy Engineering
• /
• v.13 no.1
• /
• pp.1-11
• /
• 2004

Gasification is the essential technology that can meet the interim hydrogen demand of large quantity before entering the hydrogen economy. Although the hydrogen production that is based upon the pure renewable energy like wind and solar power will eventually prevail, the interim mass production of hydrogen for the next ten to twenty years will come from the technologies that can demonstrate the economic feasibility in production cost with a high potential in minimizing CO$_2$ generation and in improving plant efficiency. Particularly, feedstock such as natural gas, coal, petroleum residual oil, wastes, and biomass appears to be utilized in Korea as hydrogen source, at least during the short and medium period of time, owing to the advantage in production cost. Because one of the main reasons behind the recent hydrogen issue is the reduction requirement of CO$_2$ that would be controlled according to the climate change protocol, hydrogen production technologies must be developed to yield the minimal CO$_2$ generation.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.17 no.10
• /
• pp.1068-1078
• /
• 2004

In this paper we investigated the characteristics of surface degradation in silicone rubber due to corona exposure and recovery mechanism. It was shown that surface free energy was 22.42 mJ/$m^2$ on initial sample but surface free energy was approximately increased to 71.14 mJ/$m^2$ after 45 minutes. However, surface free energy on silicone rubber after corona discharge treatment was completely recovered within a short time due to diffusion of low molecular weight(LMW) silicone fluid. It was shown that corona discharge insured the increase of diffusible LMW chains, which could lead to recover the surface hydrophobicity. 200～370 g/mol distribution of LMW silicone fluid which was extracted by solvent-extraction with gel permeation chromatography (GPC) was contributed to recovery. The surface degradation characteristics on silicone rubbers and the recovery mechanism based on our results were discussed.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.12 no.3
• /
• pp.1-8
• /
• 2008

We present a model for simulating high energy laser heating of metal for ignition of energetic materials. The model considers effect of ablation of steel plate with long laser pulses and continuous lasers of several kilowatts and the thermal response of well-characterized high explosives for ignition. Since there is enough time for the thermal wave to propagate into the target and to create a region of hot spot in the high explosives, electron thermal diffusion of ultra-short (femto- and pico-second) lasing is ignored; instead, heat diffusion of absorbed laser energy in the solid target is modeled with thermal decomposition kinetic models of high explosives. Numerically simulated pulsed-laser heating of solid target and thermal explosion of RDX, TATB, and HMX are compared to experimental results. The experimental and numerical results are in good agreement.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.24 no.10
• /
• pp.809-816
• /
• 2014

This paper presents a systematic optimization process for designing an electromagnetic vibration energy harvester using FEA(finite element analysis) to improve computational accuracy and efficiency. A static FEA is used in the optimization process where trend analysis in a short period of time is rather important than precise computation, while a dynamic FEA is used in the verification step for the final result where precise computation is more important. An electromechanical transduction factor can be calculated efficiently by using an approach to use the radial component of magnetic flux density directly instead of an approach to compute the flux density gradient. The proposed optimization process was verified through a case study where simulation and experiment results were compared.

• Journal of the Korean institute of surface engineering
• /
• v.49 no.6
• /
• pp.567-574
• /
• 2016

We have analyzed chemical properties of polysiloxane and polysilazane films, respectively, as sealing materials for electrostatic chuck (ESC) and have investigated the possibility of polysilazane as an alternative sealant to polysiloxane. It has been revealed that Si-O with organic bonding ($Si-CH_3$) existed in polysiloxane films compared to only pure Si-O bonding in polysilazane films. The sealing property of polysilazane has been found outstanding even in a short time of application. In the polysiloxane films containing $H_2O$, pin holes have been found possibly due to $CO_2$ gas evolution, and low adhesion with Si substrate has been observed after heat stress test in connection with the existence of organic bonding. After acid resistance test in 0.5 vol.% HF, 68 wt.% $HNO_3$, and 37 wt.% HCl solution, polyilazane films have shown a longer survival times. Compared to the conventional polysiloxane sealant, polysilazane is expected as a new sealing material because of good thermal and chemical stability.

• Carbon letters
• /
• v.5 no.1
• /
• pp.12-17
• /
• 2004

In this study, the oxyfluorination of PAN-based carbon fibers was undertaken at room temperature using fluorine-oxygen mixtures, and the influence of oxyfluorination on properties was investigated. The surface characteristics of the modified fiber were determined by using X-ray photoelectron spectroscopy (XPS) and dynamic contact angle analyzer. The oxyfluorination of carbon fibers was one of the more effective methods to increase surface wettability by the formation of semicovalent C-F bond and C-O bond depending on reaction conditions. When oxygen mole fraction is increased from 0.5 to 0.9, it is probable that attached fluorine atoms at the surface of the fibers reacted with other components. As increased oxyfluorination time and decreased its pressures, semi-covalent peak is increased at 0.5 of oxygen mole fraction. The total surface free energy of oxyfluorinated carbon fibers decreased with increasing oxygen mole fraction over 0.5. These results indicate that the surface of carbon fibers became much more hydrophilic after the short oxyfluorination. The surface free energy of oxyfluorinated carbon fibers progressively decreased after 10 min treatment. The polar components of surface free energies were however, significantly higher for all oxyfluorinated samples than that for the untreated carbon fiber.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 1999.11a
• /
• pp.520-524
• /
• 1999

The Impact ionization rate is highly anisotropic at low electron energy, while it becomes isotropic at higher energy range in which impact ionization events frequently accur. In this study, full energy band structure obtained by pseudopotential method and Fermi's golden rule is used to calculate impact ionization rate. The calculated impact ionization rate is well fitted to a modified Keldysh formular at 300K and 77K. Full band Monte Carlo simulator is made to investigate the validity of the GaAs impact ionization coefficients at 300K and 77K. Impart ionization process is isotropic under the condition of steady state since anisotrophy appears during very short time at look. Impart ionization coefficients is nearly constant and is anisotropic in electric field applied along the <110> direction at 77K.

• Journal of Korean Society on Water Environment
• /
• v.23 no.4
• /
• pp.551-560
• /
• 2007

The present study analyzed noise reduction and long/short-term components for discharge, TOC concentration, and TOC load data in order to understand the data characteristics better. For the purpose, wavelet transform which can reduce noise from raw data and has flexible resolution in time and frequency domain was applied and the theory of nonlinear dynamics was also used to determine the last decomposition level for wavelet transform. Wavelet function of 'db10' and the 7th level for the last decomposition of wavelet transform were applied for the all data in the present study. Also the results revealed that the energy ratios of approximation components with 187-hour periodicity decomposed from 7th level of wavelet transform were 94.71% (discharge), 99.00% (TOC concentration), and 93.84% (TOC load), respectively. In addition, the energy ratios of detail components showed the range between 1.00% and 6.17%, which were extremely small comparing to the energy ratios of approximation components, therefore, the first and second detail components might be considered as noise components included in the raw data.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2015.05a
• /
• pp.240-240
• /
• 2015

As Simpson et al. (1990) emphasized the importance of the straining process in the stratification and mixing in the estuarine circulation process, various researches have investigated on the relative contribution of each process to the overall potential energy anomaly dynamics. However, many numerical works have done only for two dimensional modeling along channel or the short distance cross sectional three dimensional simulations as Burchard et al. (2008) and the estuarine channel was not simulated so far. But, in the study on the physics of shallow coastal seas, spatial dimension in the three dimensional way affects significantly on results of a particular numerical model. Therefore, the comparison of two and three dimensional models is important to understand the real physics of mixing and stratification in an estuary. Also, as Geyer and MacCready (2013) pointed out that the lateral process seems to be important in determining the periodic stratifications, to study such process the three dimensional modeling must be required. The present study uses a numerical model to show the signification roles of each term of the time-dependent dynamic equation for the potential energy anomaly (PEA) in controlling along and lateral channel flows and different stratification structures. Moreover, we present the relationships between the ${\Phi}$-advection, the depth mean straining, vertical mixing and vertical advection can explain well how water level, salinity distribution and across velocity 2D model are slightly different from 3D.

• Ocean and Polar Research
• /
• v.40 no.4
• /
• pp.271-280
• /
• 2018

The purpose of this study is to examine the causal relationship among oil consumption, oil-tanker accidents, and economic growth, and to derive policy implications from the results. Therefore, this paper attempts to analyze the short term, long term, and strong causality factors pertaining to the relationship between oil consumption, oil-tanker accidents, and economic growth in Korea using time-series techniques and annual data for the 1984-2016 period. Tests for unit roots, co-integration, and Granger-causality based on an error-correction model are presented. The results show that bidirectional causality exists between oil consumption and oil-tanker accidents, between economic growth and oil consumption, and between oil-tanker accidents and economic growth. The study shows that oil was used as a core energy source during the rapid economic growth of Korea in the past, and that this caused the number of oil-tanker accidents to rise as oil consumption increased.