• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1996년도 추계학술대회 논문집
• /
• pp.371-376
• /
• 1996

The damping force of shock absorber in an automobile is determined by the components which construct the S/A. In this study we investigate the individual effect of these components on damping force. In addition, opening of important valve doling compression and tension cycle due to up-down reciprocation movement is also researched. Thus we are to strictly control the properties and tolerance of components having important effects on tile damping force and to produce S/A of better quality.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2004년도 춘계학술대회
• /
• pp.973-977
• /
• 2004

A pneumatic cylinder used to sliding seal which seal the element one to another in relative motion. It is difficult to accuracy control because of adhesion phenomenon. To confirm this phenomenon, it is carried to friction force test and analysis for bellows type rodless cylinder. In the rodless cylinder of this type, friction force test is very important. Through the theoretical analysis of shock absorber obtained the optimal design of bellows type rodless cylinder. As the result of the friction force test, LM Guide type is suitable for work under low friction force.

• 한국운동역학회지
• /
• 제30권2호
• /
• pp.145-154
• /
• 2020

Objective: The purpose of this study was to determine the relationship between impact and shear peak force, and tibia-accelerometer variables during running. Method: Twenty-five male heel strike runners (mean age: 23.5±3.6 yrs, mean height: 176.3±3.3 m/s, mean mass: 71.8±9.7 kg) were recruited in this study. The peak impact and anteroposterior shear forces during treadmill running (Bertec, USA) were collected, and impact shock variables were computed by using a triaxial accelerometer (Noraxon, USA). One-way ANOVA was used to test the influence of the running speed on the parameters. Pearson's partial correlation was used to investigate the relationship between the peak impact and shear force, and accelerometer variables. Results: The running speed affected the peak impact and posterior shear force, time, slope, and peak vertical and resultant tibial acceleration, slope at heel contact. Significant correlations were noticed between the peak impact force and peak vertical and resultant tibia acceleration, and between peak impact average slope and peak vertical and resultant tibia acceleration average slope, and between posterior peak (FyP) and peak vertical tibia acceleration, and between posterior peak instantaneous slop and peak vertical tibial acceleration during running at 3 m/s. However, it was observed that correlations between peak impact average slope and peak vertical tibia acceleration average slope, between posterior peak time and peak vertical and resultant tibia acceleration time, between posterior peak instantaneous slope and peak vertical tibial acceleration instantaneous slope during running at 4 m/s. Conclusion: Careful analysis is required when investigating the linear relationship between the impact and shear force, and tibia accelerometer components during relatively fast running speed.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1995년도 추계학술대회 논문집
• /
• pp.942-946
• /
• 1995

Using database obtained by means of experiments, or using the synamic behaviour analysis program of automotive shock absorber, database system is constructed within the limits of adequate reliability. Thus constructed data base can be used to find out corresponding specification of shock absorber design parameters to the required damping ability and tolerance.

• 동력기계공학회지
• /
• 제15권4호
• /
• pp.11-18
• /
• 2011

A Shock absorber is one of the most important components in vehicle suspension systems. In general, many repeated analyses are required for the design of a shock absorber to satisfy the suspension characteristics of a specific automobile, like fluid flow analysis and mechanical analysis. The purpose of this study is to develop a fast design tool for shock absorber designers. One of the efficient solutions for this can be an empirical design method considering phenomenological effects from the shock absorber design variables. In order to extract the shock absorber's experimental characteristics, we used Taguchi method. This method showed that which design variables have major effects for the shock absorber's damping characteristics. This empirical design method also showed the direction of the design changes to satisfy the designer's intension.

• 한국군사과학기술학회지
• /
• 제22권5호
• /
• pp.581-589
• /
• 2019

Guided missiles assembled with the bolted joint are subjected to various shock loading conditions while flying in the air and operating on the ground or platform. Especially, It is important to analyze the effect of the shock load on the structure because it affects the structure for a short duration time while its acceleration magnitude is quite large. In this study, mechanical shock tests on the structure with the bolted joint have been carried out to measure the acceleration changes of the structure against external shock loads by electrical exciter. Variation of dynamic characteristics of a structure with fastening methods and fastening forces has been investigated through Shock Response Spectrum analysis.

• 한국전자통신학회논문지
• /
• 제15권5호
• /
• pp.949-958
• /
• 2020

차량을 구성하는 엔진, 미션, 현가, 제동, 조향장치 등 다양한 장치 중에서 현가 장치는 타이어와 차체 사이에 설치되어 노면에 의한 차량의 진동을 억제하여 승차감을 향상시키고 차륜과 노면 사이에 적절한 접지력을 유지시켜 차량의 조정안정성을 향상시키는 등 차량역학적인 측면에서 많은 영향을 미치는 장치 중의 하나이다. 본 연구에서는 차량용 현가 장치의 충격 흡수기를 실제 특성과 유사한 상세 모델로 모델링하고, 충격 흡수기의 주요 설계변수의 불확실성을 통계적으로 고려하여 설계변수의 불확실성이 현가 장치의 동적 특성에 미치는 영향에 대하여 연구하였다.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2017년도 제48회 춘계학술대회논문집
• /
• pp.310-319
• /
• 2017

충격파 시험장치를 이용하여 추력을 측정하는 방법을 소개하였다. 충격파 시험장치를 이용하여 엔진의 추력을 측정하기 위해서는 일반적인 엔진시험 시설에서 추력을 측정하기 위해 사용하는 밸런스가 힘의 평형상태에 도달하지 못하기 때문에 응력파 힘 밸런스(Stress Wave Force Balance) 방법을 이용하여 측정한다. 본 논문에서는 모델 힘 밸런스(force balance)에 대해 충격하중을 주고 유한요소법(FEM)으로 변형률을 계산하였다. 충격하중과 변형률의 관계를 역합성곱(de-convolution)하여 천이함수를 도출하였다.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2012년도 추계학술대회 논문집
• /
• pp.81-86
• /
• 2012

The shock absorber is very important in various mechanical field. Without the shock absorber, the structure might be broken. For lunar lander, honeycomb shock absorber to absorber the shock by using plastic deformation of honeycomb has been used. It is cheap and simple to use but impossible using again without changing the honeycomb. The oleo-pneumatic type shock absorber is not able to use in the cosmos because it is vacuum and its temperature. This study suggests the hybrid shock absorber combined spring-ratchet mechanical shock absorber and eddy current electromagnetic damper. The ratchet restricts rebound of lunar lander and the spring converts the impact energy to the potential energy of the spring. The eddy current damper dissipates the impact energy by eddy current force without contact between the parts. This hybrid shock absorber is reusable while the honeycomb shock absorber isn't. The impact absorbing test of the hybrid shock absorber was carried out. This paper shows that the compared results the hybrid shock absorber with ratchet and without ratchet and evaluates the possibility of using for lunar lander.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2006년도 제37회 하계학술대회 논문집 B
• /
• pp.653-654
• /
• 2006

This paper proposes a new linear magnetic damper for absorbing shock from a crash accident involving high speed vehicles. The magnetic damper is composed of a conductive plate, a yoke and permanent magnets which are constructed to a Halbach array to improve the damping force. In order to calculate the damping force, finite element analysis(FEA) using J-Mag, a commercial FEA tool, is performed and the results are validated by the experiment. Also, the design optimization of the plate generating the eddy current causing the damping force performed to obtain the most efficient damping force. Finally, the specifications and the performance of the proposed magnetic damper are represented.