• 대한조선학회논문집
• /
• 제52권6호
• /
• pp.478-484
• /
• 2015

Knowledge about ice load distribution along the ship hull due to ship-ice interaction can provide important background information for the development of design codes for ice-going vessels. The objective of this study is to understand ship and ice interaction phenomena and determine the magnitude of ice load acting along a ship hull. The model tests were performed in the ice model basin in Korea Research Institute of Ships and Ocean engineering (KRISO) with the model of icebreaking ship Araon. Self-propulsion tests in level ice were performed with three difference model ship speeds. In the model tests, three tactile sensors were installed to measure the spatial distribution of ice load acting at different locations on a model ship, such as the bow and shoulder areas. Variation in the distribution of ice load acting on a model hull with ship speed is discussed.

• International Journal of Naval Architecture and Ocean Engineering
• /
• 제10권3호
• /
• pp.385-392
• /
• 2018

This paper presents 2D numerical modeling to calculate ship-ice interactions that occur when an icebreaker advances into ice-covered water. The numerical model calculates repeated icebreaking of an ice plate and removal of small ice floes. The icebreaking of the ice plate is calculated using a ship-ice contact detection technique and fluid-structural interaction of ice plate bending behavior. The ship-ice interactions in small ice floes are calculated using a physically based modeling with 3DOF rigid body equations. The ice plate is broken in crushing, bending, and splitting mode. The ice floes drift by wind or current and by the force induced by the ship-ice interaction. The time history of ice force and ice floe distribution when an icebreaker advances into the ice-covered water are obtained numerically. Numerical results demonstrate that the time history of ice force and distribution of ice floes (ice channel width) depend on the ice floe size, ship motion and ice drifting by wind or current. It is shown that the numerical model of ship maneuvering in realistic ice conditions is necessary to obtain precise information about the ship in ice-covered water. The proposed numerical model can be useful to provide data of a ship operating in ice-covered water.

• International Journal of Naval Architecture and Ocean Engineering
• /
• 제11권2호
• /
• pp.796-808
• /
• 2019

In this paper, a Smoothed Particle Hydrodynamics (SPH) method is extended to simulate the ice failure process and ice-ship interactions. The softening elastoplastic model integrating Drucker-Prager yield criterion is embedded into the SPH method to simulate the failure progress of ice. To verify the accuracy of the proposed SPH method, two benchmarks are presented, which include the elastic vibration of a cantilever beam and three-point bending failure of the ice beam. The good agreement between the obtained numerical results and experimental data indicates that the presented SPH method can give the reliable and accurate results for simulating the ice failure progress. On this basis, the extended SPH method is employed to simulate level ice interacting with sloping structure and three-dimensional ice-ship interaction in level ice, and the numerical data is validated through comparing with experimental results of a 1:20 scaled Araon icebreaker model. It is shown the proposed SPH model can satisfactorily predict the ice breaking process and ice breaking resistance on ships in ice-ship interaction.

• International Journal of Naval Architecture and Ocean Engineering
• /
• 제9권2호
• /
• pp.209-218
• /
• 2017

Sea ice is the main factor affecting the safety of the Arctic engineering. However, traditional numerical methods derived from classical continuum mechanics have difficulties in resolving discontinuous problems like ice damage. In this paper, a non-local, meshfree numerical method called "peridynamics", which is based on integral form, was applied to simulate the interaction between level ice and a cylindrical, vertical, rigid structure at different velocities. Ice in the simulation was freshwater ice and simplified as elastic-brittle material with a linear elastic constitutive model and critical equivalent strain criterion for material failure in state-based peridynamics. The ice forces obtained from peridynamic simulation are in the same order as experimental data. Numerical visualization shows advantages of applying peridynamics on ice damage. To study the repetitive nature of ice force, damage zone lengths of crushing failure were computed and conclude that damage zone lengths are 0.15-0.2 times as ice thickness.

• International Journal of Naval Architecture and Ocean Engineering
• /
• 제12권1호
• /
• pp.957-966
• /
• 2020

This paper presents the virtual mass method to implement the prediction of total resistance for ice-going ship in floe ice region based on the combined method of CFD and DEM. Two ways of floe ice distribution are adopted for the analysis and comparison. The synthetic ice model test has been conducted to determine the optimal virtual mass coefficients for the two different floe ice distributions. Moreover, the further verification and prediction are developed in different ice conditions. The results show that, the fixed and random distributions in numerical method can simulate the interaction of ship and ice vividly, the trend of total resistance varying with the speed and ice concentration obtained by the numerical simulation is consistent with the model test. The random distribution of floe ice has higher similarity and better accuracy than fixed distribution.

• 한국해양공학회지
• /
• 제28권2호
• /
• pp.126-132
• /
• 2014

In this study, a method for analyzing the collision and interaction between ice bergy bits and a Mark III type liquid natural gas (LNG) carrier was considered, and the structural safety of a ship's hull and cargo containment system (CCS) was evaluated. In the analysis, a constitutive model implementing the strain rate dependant mechanical property was used to consider the typical material characteristics of ice rationally. A relatively simple and easy ice structure interaction analysis procedure, compared with the accurate but complicated FSI analysis scheme, was suggested. When the ice bergy bits collided with ship's side hull under the four assumed scenarios, the structural behaviors of the ship structure and LNG CCS were simulated by applying the suggested ice collision analysis procedure using the commercial hydro-code LS-DYNA. In addition, the effects of the shapes and colliding speed of the ice bergy bits on the ice-structure interaction and safety of the CCS were examined in detail.

• 대한조선학회논문집
• /
• 제53권2호
• /
• pp.85-91
• /
• 2016

The most important factor in the structural design of ships and offshore structures operating in arctic region is ice load, which results from ice-structure interaction during the ice collision process. The mechanical properties of ice related to strength and failure, however, show very complicated aspect varying with temperature, volume fraction of brine, grain size, strain rate and etc. So it is nearly impossible to establish a perfect material model of ice satisfying all the mechanical characteristics completely. Therefore, in general, ice collision analysis was carried out by relatively simple material models considering only specific aspects of mechanical characteristics of ice and it would be the most significant cause of inevitable errors in the analysis. Especially, it is well-known that the most distinctive mechanical property of ice is high dependency on strain rate. Ice shows brittle attribute in higher strain rate while it becomes ductile in lower strain rate range. In this study, the simulation method of ice collision to ship hull using the nonlinear dynamic FE analysis was dealt with. To consider the strain rate effects of ice during ice-structural interaction, strain rate dependent constitutive model in which yield stress and hardening behaviors vary with strain rate was adopted. To reduce the huge amount of computing time, the modeling range of ice and ship structure were restricted to the confined region of interest. Under the various scenario of ice-ship hull collision, the structural behavior of hull panels and failure modes of ice were examined by nonlinear FE analysis technique.

• International Journal of Naval Architecture and Ocean Engineering
• /
• 제5권1호
• /
• pp.116-131
• /
• 2013

The resistance performance of an icebreaking cargo vessel in pack ice conditions was investigated numerically and experimentally using a recently developed finite element (FE) model and model tests. A comparison between numerical analysis and experimental results with synthetic ice in a standard towing tank was carried out. The comparison extended to results with refrigerated ice to examine the feasibility of using synthetic ice. Two experiments using two different ice materials gave a reasonable agreement. Ship-ice interaction loads are numerically calculated based on the fluid structure interaction (FSI) method using the commercial FE package LS-DYNA. Test results from model testing with synthetic ice at the Pusan National University towing tank, and with refrigerated ice at the National Research Council's (NRC) ice tank, are used to validate and benchmark the numerical simulations. The designed ice-going cargo vessel is used as a target ship for three concentrations (90%, 80%, and 60%) of pack ice conditions. Ice was modeled as a rigid body but the ice density was the same as that in the experiments. The numerical challenge is to evaluate hydrodynamic loads on the ship's hull; this is difficult because LS-DYNA is an explicit FE solver and the FSI value is calculated using a penalty method. Comparisons between numerical and experimental results are shown, and our main conclusions are given.

• Journal of Advanced Research in Ocean Engineering
• /
• 제2권2호
• /
• pp.67-80
• /
• 2016

The resistance performance of an icebreaking cargo vessel with varied stem angles is investigated numerically and experimentally. Ship-ice interaction loads are numerically calculated based on the fluid structure interaction (FSI) method using the commercial FE package LS-DYNA. Test results obtained from model testing with synthetic ice at the Pusan National University towing tank and with refrigerated ice at the National Research Council's (NRC) ice tank are used to validate and benchmark the numerical simulations. The designed icebreaking cargo vessel with three stem angles ($20^{\circ}$, $25^{\circ}$, and $30^{\circ}$) is used as the target ship for three concentrations (90%, 80%, and 60%) of pack ice conditions. The comparisons between numerical and experimental results are shown and our main conclusions are given.

• Journal of Ship and Ocean Technology
• /
• 제8권2호
• /
• pp.29-40
• /
• 2004

Interaction of grounded ice ridges with underlying seabed is one of the major considerations in the design of Arctic pipeline system. Previously several ice scour models were developed by researchers to describe the ice scour-seabed interaction mechanism. In this paper, a parametric study on ice scouring mechanism is performed and the limitation of ice scour-seabed interaction models is discussed. Simple laboratory tests are carried out and then the shape pattern of deposited soil around the ice is redefined. New ice scour model assumes trapezoidal cross section based on the field observation data. Ice scour depth and soil resistance forces on seabed are calculated with varying the keel angle of a model ice ridge.