• Journal of Advanced Marine Engineering and Technology
• /
• v.37 no.6
• /
• pp.611-616
• /
• 2013

Many researches have been carried out consistently for the green ship owing to its economic increasement, efficiency and convenience. One of them is an electronic controlled marine diesel engine. However, we are suffered from dissemination of above engine, due to its anxiety about safety and reliability. In order to solve these problems in this study, emission characteristics test of main propulsive two-stroke diesel engine, equipped both electronic control and cam drive fuel injection systems, has been performed and evaluated under the various load conditions. From the test results, we have confirmed that exhaust gas emission characteristics of the electronic control system is similar to the cam drive system in eco-mode operation, but NOx in emission mode has been decreased 100ppm or more in full load condition. HC emission from the electronic control system is decreased 10~20ppm at 50% load, and 35~40ppm at 25% load in comparison to cam drive system. In fuel consumption, it is considered that 7g/kWh is decreased than the value of cam drive system at 700bar of injection pressure, which is 200bar higher than cam drive system.

• Journal of Advanced Marine Engineering and Technology
• /
• v.39 no.7
• /
• pp.716-721
• /
• 2015

As the severity of environmental pollution has increased, restrictions on air pollution have been strengthened. Stringent regulations have been imposed, not only on marine diesel engines but also on automotive and industrial power plants. Thus, biofuels have been directly applied in practical engines and used in training ships for basic research. Even though a high biofuel percentage cannot be used in a training ship engine for safety reasons, because this type of engine is larger than those used in institutional laboratories, the results will provide important basic information that will allow organizations to determine the status of a large output. Biodiesel fuel was studied to determine how it would affect the combustion characteristics and exhaust emissions of a marine diesel generator engine. The main results can be summarized as follows. Because the physical and chemical compositions of biofuels are similar to those of diesel fuel, it was found that their practical use was possible in a training ship. The specific fuel consumption and NOx increased, whereas a tendency was found for carbon monoxide and soot to decrease. In addition, no significant pressure change difference was found between the diesel fuel and biofuels.

• Journal of Advanced Marine Engineering and Technology
• /
• v.38 no.7
• /
• pp.877-882
• /
• 2014

The reduction of CO2 emission has been discussed in the Marine Environment Protection committee in the International Maritime Organization as the biggest causes of GHG for the purpose of indexing CO2 amounts released into the atmosphere from ships. Accordingly, various methods including the change in the hull design to improve energy efficiency, the coating development to reduce friction resistances, the additives development for improving thermal efficiency in an engine, the low-speed operation to reduce fuel consumptions, and etc. have been applied. The main engine of a ship is an electronic engine for improving the efficiency of the whole load area. However, marine generator engines still use mechanical drive engines in intake, exhaust, and fuel injection valve drive cams. In addition, most of marine generator engines in ships apply a part-load operation of less then 80% due to an overload protection system. Therefore, marine auxiliary diesel engine set at 100% load is necessary to readjust in order to efficient operation because of part-load operation. The objective of this study is to report the results of the part-load fuel consumption improvement by injection timing readjust to identifying the operational characteristics of a marine generator engine currently operated in a ship.

• Proceedings of the KIEE Conference
• /
• 2011.07a
• /
• pp.1228-1229
• /
• 2011

A novel approach has been promoted for FNN ship controllers. An Electro-hydraulic governor has been widely adopted to the ship speed control of propulsion marine diesel engines for a long time, it was very difficult for Electro-hydraulic governor to regulate the speed of high power engine with long stroke at low speed and low load, because of the jiggling phenomena by rough fluctuation of rotating torque and the hunting phenomena by long dead time occurred in fuel combustion process in the engine cylinder. This paper provides an efficient way for improving control performance by FNN controller. An RBF neural network and GA optimization are employed in a fuzzy neural controller to deal with the nonlinearity, time varying and uncertain factors, the rule base and membership functions can be auto-adjusted by GA optimization. The parameters of neural network can be decreased by using union-rule configuration in the hidden layer of the network. The performance of controller is evaluated by the system simulation using simulink tools.

• Journal of Fisheries and Marine Sciences Education
• /
• v.25 no.3
• /
• pp.705-715
• /
• 2013

This Paper presented the reduction methods of $CO_2$ emission from ships during voyage. In order to decrease $CO_2$ emission during voyage the equation was established and conducted the study about the relationship between ship speed, the propulsive efficiency and its $CO_2$ production. The results obtained from the examinations are as follows : 1. $CO_2$ emission from sailing ships can be decreased by reducing specific fuel oil consumption of main diesel engine, coefficient of total resistance and ship speed and also by increasing propeller efficiency. 2. Diesel-electric propulsion system is more effective than diesel-mechanical system to decrease the level of $CO_2$ emission during long voyage. 3. Good condition of ship's hull surface, rudder and propeller's surface can decrease the quantity of fuel oil and $CO_2$ emission by reducing the resistance of ship that can rise the propeller efficiency 4. $CO_2$ emitted from ships can be decreased in a global scale by giving attention to the synthetic transport efficiency.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.21 no.5
• /
• pp.1049-1059
• /
• 2017

After patrol corvett Cheonan was hit and sank on duty, the Republic of Korea Navy has tried to install hybrid propulsion system on naval ship to reduce vibration and noise problems during navigation. The hybrid propulsion system has advantage that propulsion motor can be propelled in low speed operation of the vessel. This can be a better quietness than a mechanical propulsion system which consists of a conventional internal combustion engines. And more economical operation is possible by using a propulsion motor in a low speed operation where a fuel efficiency of the internal combustion engine is poor. In this paper, we set up virtual ship on the basis of a combat support ship in the Republic of Korea Navy, economically compared and analyzed fuel consumption between conventional and hybrid propulsion system. As a result, it was confirmed that the fuel efficiency of hybrid propulsion system which use electric motor had been relatively improved.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.28 no.3
• /
• pp.451-458
• /
• 2022

In Korea, five major ports have been designated as sulfur oxide emission control areas to reduce air pollutant emissions, in accordance with Article 10 of the "Special Act on Port Air Quality" and Article 32 of the "Ship Pollution Prevention Regulations". As regulations against vessel-originated air pollutants (such as PM, CO2, NOx, and SOx) have been strengthened, the Ministry of Oceans and Fisheries(MOF) enacted rules that newly built public ships should adopt eco-friendly propulsion systems. However, particularly in diesel-electric hybrid propulsion systems,the demand for precise control schemes continues to grow as the fuel saving rate significantly varies depending on the control strategy applied. The conventional Power Take In-Power Take Off(PTI - PTO) mode control adopts a rule-based strategy, but this strategy is applied only in the low-load range and PTI mode; thus, an additional method is required to determine the optimal fuel consumption point. The proposed control method is designed to optimize fuel consumption by applying the equivalent consumption minimization strategy(ECMS) to the PTI - PTO mode by considering the characteristics of the specific fuel oil consumption(SFOC) of the engine in a diesel-electric hybrid propulsion system. To apply this method, a specific fishing vessel model operating on the Korean coast was selected to simulate the load operation environment of the ship. In this study, a 10.2% reduction was achieved in the MATLAB/SimDrive and SimElectric simulation by comparing the fuel consumption and CO2 emissions of the ship to which the conventional rule-based strategy was applied and that to which the ECMS was applied.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.39C no.9
• /
• pp.767-773
• /
• 2014

An economic ship routing means to sail a ship with a goal of minimizing the fuel consumption by utilizing weather forecast information, and there have been various systems which have been recently studied. For a successful economic ship routing system, it is needed to properly control an engine power or change a geographical path considering weather forecast. An optimal geographical path is difficult to be determined, though, because it is a minimal dynamic-cost path search problem where the actual fuel consumption is dynamically variable by the weather condition when the ship will pass the area. In this paper, we propose an geographical path-search algorithm based on evolutionary strategy to efficiently search a good quality solution out of tremendous candidate solutions. We tested our approach with the shortest path-based sailing method over seven testing routes and observed that the former reduced the estimated fuel consumption than the latter by 1.82% on average and the maximum 2.49% with little difference of estimated time of arrival. In particular, we observed that our method can find a path to avoid bad weather through a case analysis.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.19 no.5
• /
• pp.525-530
• /
• 2013

In this study, the generator engine of training ship M/S "HAE RIM" of Kunsan National University which is being operated for 20 years was used in the experiment. The experiment was carried out under the engine speed of 1200rpm, then the load was varied 30 kW intervals from 0 to 90 kW and the injection timing was varied $2^{\circ}$CA intervals from BTDC $19^{\circ}$ to $23^{\circ}$CA. In the case of advancing fuel injection timing from BTDC $21^{\circ}$CA to $23^{\circ}$CA, specific fuel consumption is decreased by 1.37%, NOx is increased by 11.59 %, soot is decreased by 23.5 % and $SO_2$ is decreased by 2.8 %. Accoring to the analysis of effects of fuel injection timing on combustion & exhaust emissions characteristics on an old marine diesel engine, it is proved that the optimum fuel injection timing is BTDC $23^{\circ}$ which is $2^{\circ}$ faster than that of original injection timing.

• Proceedings of KOSOMES biannual meeting
• /
• 2017.04a
• /
• pp.244-244
• /
• 2017

Recently, A study is actively underway to apply to various industries, which are one of the major changes in the key drivers of the industry 4.0.. The data generated by the ship include various indicators such as the fuel volume, engine power, ground speed, speed, speed, main engine rpm, DFOC, SFOC, and FOC. This paper analyzes the sensitivity of the Gathering data and analyzes the impact energy efficiency of the vessel operation by analyzing the influence among each parameter, using the mathematical models, you create an surrogate model using the math model, comparative analysis of actual measurement data and predictive results were analyzed. Through the use of big data analysis technology, it is possible to identify the sensitivity between the energy efficiency related variables of the ship, The possibility of utilization of fuel efficiency indicators using of the surrogate model is identified.