• Journal of Ocean Engineering and Technology
• /
• v.33 no.4
• /
• pp.330-339
• /
• 2019

Radiant heat shields are normally installed on offshore oil and gas platforms to protect personnel, equipment, and structures from the thermal radiation emitted by a flare system. A heat shield should be individually designed to reduce the thermal radiation to the target level, and then manufactured and installed after the performance verification. However, in general, a heat shield is designed and manufactured by trial and error based on the performance test. For this reason, it is difficult to develop and design radiant heat shields in the Korean shipbuilding and marine equipment industry because of the lack of performance test data and limited experience. In the present study, the results of experiments conducted to verify the performances of radiant heat shields were analyzed, and the thermal radiation characteristics and performance characteristics of the radiant heat shields were investigated. The insights and conclusions developed in the present study will be useful in terms of the design and development of radiant heat shield, as well as in their performance verification tests.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2002.10a
• /
• pp.29-50
• /
• 2002

Based on the investigation results on the damages of some underground structures due to the severe Kobe Earthquake it concludes that the aseismicity of underground is far superior to that of aboveground structures. Therefore, at first, necessity to reconstruct strong cities especially by good use of underground space will be discussed. Then two non-circular shield-tunneling projects in Japan are discussed. The first is construction of the world's first shield driven double track subway tunnel of rectangular shape for the Kyoto Municipal Subway. This paper presents a report on the overall planning, the tests that were performed in the process of planning, and the results of driving. The second is the design of the Hirakata Tunnel, with three traffic lanes and shoulders on one side, which will be constructed as one of the tunnels for The New Meishin (Nagoya-Kobe) Expressways. This paper presents the feasibility study of the shield tunneling method, using the same design criteria as the non-circular, horseshoe section of mountain tunnel, to the equivalent section of the Hirakata Tunnel.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.60 no.4
• /
• pp.694-699
• /
• 2011

This paper compares the performance of lightning shielding analysis methods using the seven striking distance formulae in substation. For comparison, we evaluate the number of expected strikes and exposed area using WinIGS Software. Seven striking distance formulae are compared using the electrogeometric model analysis and the rolling sphere method. Based on the electrogeometric model analysis, the risk of shielding failure in either the whole substation or parts of it is determined. According to the simulation results, one can justify whether the substation satisfies the criterion of shielding design. In particular, according to the rolling sphere method, the exposed areas in substation determine the location of the additional shielding poles or shield wires. Therefore, the installation of the additional shielding poles and shield wires in substation was accepted by shield design at the phase conductors exposed in the larger area.

• Proceedings of the KIEE Conference
• /
• 2005.07b
• /
• pp.1210-1212
• /
• 2005

High temperature superconducting(HTS) power cable system consists of HTS cable, termination and cryogenic system. And the HTS cable consists of the former, HTS phase conductor, electric insulation, HTS shield and cryostat. Taking the advantage of HTS shield, the cold dielectric has been adopted. The phase conductor and the shield have been designed to minimize the AC loss below 1W/m/phase. The former has been designed to transport the fault current of 25kA, at fault condition. This paper describes the design process of 22.9kV HTS cable considering AC losses at normal state and the stability at fault condition.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• v.y2005m4
• /
• pp.27-30
• /
• 2005

Hanwha Corporation succeeded in domestic development of thruster heat shield for KOMPSAT-2 propulsion subsystem partly. Thruster heat shield, one of the main components of DTM, is designed to prevent the critical radiative heat exchange between thruster and satellite during firing. To overcome the manufacturing difficulties, an electro-forming process is preferred to classical welding process. In this case, an inner diameter of a new shield will be decreased a little due to the change of manufacturing process. The interference problem between thruster nozzle and heat shield was investigated through structural analysis by KARI. Hanwha manufactured heat shield based on the analysis results. In this paper, full development process is described for design, analysis, manufacturing of heat shield.

• The Transactions of the Korean Institute of Electrical Engineers A
• /
• v.55 no.2
• /
• pp.59-61
• /
• 2006

In our country most of transmission lines are double-circuit lines. In these lines, the combining method of increasing conductor height and installation of passive shield-loop to mitigate magnetic field near a transmission line, is a good and feasible method. The basic principle of passive shield loop is that the field from the current induced in the shield loop conductors counteracts the field from the phase conductors. This method applied to domestic transmission lines to meet the magnetic field level, 100, 30, 10 and 4 mG, respectively. In each magnetic field level, the minimum conductor height and passive loop height are presented for the implementation of the practical design.

• Proceedings of the KIEE Conference
• /
• 2004.04a
• /
• pp.12-14
• /
• 2004

Superconducting transmission power cable is one of interesting parts in power application using high temperature superconducting wire. One of import ant parameters in high-temperature superconduting (HTSC) cable design is transport current distribution because it is related with current transmission capacity and AC loss. In this paper, the transport current distribution at conducting layers was investigated through the analysis of the equivalent circuit for HTSC power cable with shield layer and compared with the case of without shield layer. The transport current distribution due to of the contact resistance and the pitch was improved in the case of HTSC power cable with shield layer from the analysis.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2013.05a
• /
• pp.961-964
• /
• 2013

Arduino is for design based on open source prototyping platform, artist, designer, hobby activists, etc, i has been designed for all those who are interested in the environment construct. Arduino adventage you can easily create applications hardware, without deep knowledge about the hardware. Configuration of arduino using AVR microcontroller ATmage 168, software to action arduino using arduino program, MATLAB, Processing. Arduino is open source base, you can hardware production directly and using shield additionally, the arduino can be combined. Android is open source. Continue to expand through a combination of hardware, Arduino. It name is shield. Be given to the Arduino Uno board to the main board, the shield extends to the various aspects and help can be equipped with more features. The shield on top of the shield can be combined as a kind of shield and Ethernet shield, motor shield, the shield RFID hardware beyond a simple extension can be configured. In this paper, sortware was used for arduino program, hardware was used for arduino Uno board, the additional shield using RFID shield. Configure the hardware to be compatible with this tag combined the 13.56MHz tag SM130.

• Proceedings of the KIEE Conference
• /
• 2002.11d
• /
• pp.80-83
• /
• 2002

A 3D shape optimization algorithm integrates the geometric parameterizationi 3D F.E. performance analysis, steepest descent method with design sensitivity and mesh relocation method. The design sensitivity of the surface nodal points is also systematically converted into that of the design variables for the application to parameterized optimization. The proposed algorithm is applied to the optimum design of tank shield model of transformer and the effectiveness is proved.

• Proceedings of the Korea Society of Design Studies Conference
• /
• 2002.05b
• /
• pp.210-211
• /
• 2002