• Proceedings of the Computational Structural Engineering Institute Conference
• /
• 1997.04a
• /
• pp.45-52
• /
• 1997

The elastic deflection of thin ice sheets due In bending and shear deformation is considered. The in-plane Young's modulus and the transverse shear modulus are calculated by least squres fit of transverse plate deflection data. Results show that thin ice plates behave predominantly in shear. Previously, the Young's moduli were calaulated based on bending theory alone. The Young's moduli of thin model ice sheets, estimated using the bending and shear theory, are more than an order of magnitude greater than calculated previously, and hence are more realistic. Further, the previous ambiguity in the Young's modulus, arising from fitting the data at various distances from the point of loading, is removed by considering shear and bending deformation.

• Proceedings of the Computational Structural Engineering Institute Conference
• /
• 2010.04a
• /
• pp.795-798
• /
• 2010

본 논문에서는 상사진동에서의 응답을 통해 구성된 모드유연도에 의해 추정되는 손상유발 변위를 이용하여 전당빌딩의 손상을 탐지하는 진동기반의 손상탐지 방법을 제시하였다. 이 방법은 전단빌딩의 층간변위를 활용하여 오직 손상이 존재할 때에만 발생하는 Damage-induced inter-story deflection (DI-ID)을 통해 손상탐지를 수행하는 방법이다. 구조물의 전체 자유도에 양의 전단력을 발생시킴으로써 층간변위를 분명히 파악할 수 있도록 하는 양전단력 탐색하중(Positive Shear Inspection Load)을 통해 DI-ID를 산정한다. 제안된 방법의 검증을 위해 5층의 전단빌딩 축소모형을 대상구조물로 선정하여 수치모의실험을 수행했다. 단일손상과 다중손상의 모사를 위해 1층과 3층의 휨강성을 각각 10% 씩 저감시켰고, 수치모의실험 결과, 단일손상과 다중손상 모두 정확히 손상발생 구역을 확인했다.

• Smart Structures and Systems
• /
• v.22 no.6
• /
• pp.689-697
• /
• 2018

This paper presents a model of the elastic curve for rectangular beams with straight haunches under uniformly distributed load and moments in the ends considering the bending and shear deformations (Timoshenko Theory) to obtain the deflections and rotations on the beam, which is the main part of this research. The traditional model of the elastic curve for rectangular beams under uniformly distributed load considers only the bending deformations (Euler-Bernoulli Theory). Also, a comparison is made between the proposed and traditional model of simply supported beams with respect to the rotations in two supports and the maximum deflection of the beam. Also, another comparison is made for beams fixed at both ends with respect to the moments and reactions in the support A, and the maximum deflection of the beam. Results show that the proposed model is greater for simply supported beams in the maximum deflection and the traditional model is greater for beams fixed at both ends in the maximum deflection. Then, the proposed model is more appropriate and safe with respect the traditional model for structural analysis, because the shear forces and bending moments are present in any type of structure and the bending and shear deformations appear.

• Magazine of the Korean Society of Agricultural Engineers
• /
• v.39 no.1
• /
• pp.54-63
• /
• 1997

The purpose of this study is to analyse deformation properties by carrying out of flexure experimentations after fabricating polymer concrete sandwich panels which are composed of the polymer concrete in facing and expanded polystyren in cores, and to provide the basic data necessary to design, fabricate and operate the structure using these polymer concrete sandwich panels The analysed result of this study is summarized as follows. 1. The result of experiment on flexural deflection indicated that the thicker the thickness of both cores and facing of the polymer concrete sandwich panels, the smaller the deflection but the larger the ultimate shear force. In addition, it was also shown that the thicker the thickness of these cores and facing, the smaller the increasing rate of the deflection with the increase of load. 2. The breaking shape of polymer concrete sandwich panels by experiment on flexure was different according to the thickness of facing. When the facing was 5mm in thickness, it was the flexure while it was the flexure and shear failure when the facing was 5mm in thickness. As a result, it seems that the thickness of the facing has a great effect on failure. 3. There were induced not only the related formula between load, deflection and deformation according to the thickness of cores and facing on the basis of the flexure experiment, but also formula between load, horizontal displacement, Then, it seems that it will be possible to estimate the above elements by using these related formulas.

• KCI Concrete Journal
• /
• v.12 no.1
• /
• pp.113-120
• /
• 2000

This paper presents the behavior and strengthening effect of reinforced concrete rectangular beams strengthened using CFRP sheets with different strengthening level. In general, normally strengthened beams are failed by interfacial shear failure (delamination) within concrete, instead of by tensile failure of the CFRP sheets. The delamination occurred suddenly and the concrete cover cracked vertically by flexure was spalled off due to the release energy. The strengthened beams were stiffer than the control beam before and after reinforcement yielding. The ultimate load considerably increased with an increase of strengthening level, while the ultimate deflection significantly decreased. The tensile force of CFRP sheets and average shear stress of concrete at delamination failure were curvilinearly proportional to the strengthening level. Therefore, the increment of ultimate load obtained by strengthening was curvilinearly proportional to the strengthening level. The averaged horizontal shear stress of concrete at the interface ranges between (equation omitted) and (equation omitted) (in kg/$\textrm{cm}^2$) depending on strengthening level.

• Journal of the Korean Society of Safety
• /
• v.14 no.1
• /
• pp.129-140
• /
• 1999

This study presents test results of RC beams strengthened by steel plates, carbon fiber sheets(CFS) and aramid fiber sheets(AFS) for increasing flexural and shear resistance. The test was performed with different parameters including the type of strengthening materials, flexural-strengthening methods and shear-strengthening methods. In case of flexural test, RC beams are initially loaded to 70% of the ultimate flexural capacity and in case of shear test loaded to 60 or 80 percent of the ultimate shear capacity and subsequently reinforced with steel plates, CFS and AFS. Experimental data on strength, steel strain, deflection, and mode of failure of the reinforced beams were obtained, and comparisons between the different shear reinforced schemes and the non-strengthened control beams were made. The test results showed that damaged RC beams strengthened by steel plates, CFS and AFS have more improved the flexural and shear capacity. For the beams with external reinforcement by steel plates, aramid fiber sheets and carbon fiber sheets increases in ultimate strength of 4 to 21, 17 to 43 and 26 to 36 percent were respectively achieved. Initial load had small effect on strength after reinforcement, but an important influence on deflection. One sheet reinforced was stronger than two sheets reinforced but less deflected than two sheets reinforced.

• Journal of the Korean Wood Science and Technology
• /
• v.34 no.5
• /
• pp.11-18
• /
• 2006

This study was carried out to evaluate the mechano-sorptive deflection of shear creep of drift pin jointed solid wood. Specimens were the solid wood of Pinus densiflora. The joint was composed with steel plate and drift pin, 85mm in length and 10mm in diameter. The creep tests were conducted under the constant loads in an variable environment. Five different shearing loads were applied parallel to the grain of specimens. The shearing loads applied were 170, 340, 510, 680 and 850 kgf. The stress levels were 10, 20, and 30, 40 and 50% of the bearing strength obtained from the tension-type lateral strength test. The creep tests for specimens were carried out for 10300 hours. A few general conclusions could be drawn from this study: The mechano-sorptive deflection (${\delta}$ ms) is defined as ${\delta}\;ms={\delta}\;t-({\delta}\;c+{\delta}\;sh)-{\delta}\;o$, where ${\delta}$ t is the total deflection, ${\delta}$ c is the pure creep, ${\delta}$ sh is shrinkage-swelling behavior, and ${\delta}$ o is the initial deflection. Changes of relative humidity may cause more severe creep deflection than those of constant humidity, especially during the drying process. The mechano-sorptive behaviors of specimens, except the effects of shrinkage and swelling, gradually increased with increasing time. The deflection is increased in desorption process and recovered in adsorption process. The deflections of drift pin jointed solid wood under different loads showed almost same tendency in all specimens. Although the creep deflection tendencies of each series are very similar, the specimens subjected to a large shearing load exhibit large creep deflections in the desorption process than do those to the small shearing load specimens.

• Journal of Korean Society of Steel Construction
• /
• v.16 no.6 s.73
• /
• pp.747-757
• /
• 2004

With steel and concrete composite beams, the incomplete interaction between the steel and the concrete slab leads to an appreciable increase in beam deflections. Moreover, encased composite beams using a deep deck plate or hollow-core PC slabs are critical to deflection due to their inherent geometry. In this paper, by using the calculation tools that were developed for a previous study on the deflection of encased composite beams considering the slip effects and load-slip curve, the shear bond stress and additional deflection induced due to interface slip of the encased composite beam are presented. It was found that the slip effects significantly contribute to the encased composite beam deflections and result in stiffness reduction of up to 30% compared to that of full shear interaction beams. The predicted results were compared with the measurement of 18 specimens tested in this study, and comparisons show a high degree of accuracy, within 6%.

• Advances in materials Research
• /
• v.6 no.1
• /
• pp.13-26
• /
• 2017

In this work we introduce a higher-order hyperbolic shear deformation model for bending and frees vibration analysis of functionally graded beams. In this theory and by making a further supposition, the axial displacement accounts for a refined hyperbolic distribution, and the transverse shear stress satisfies the traction-free boundary conditions on the beam boundary surfaces, so no need of any shear correction factors (SCFs). The material properties are continuously varied through the beam thickness by the power-law distribution of the volume fraction of the constituents. Based on the present refined hyperbolic shear deformation beam model, the governing equations of motion are obtained from the Hamilton's principle. Analytical solutions for simply-supported beams are developed to solve the problem. To verify the precision and validity of the present theory some numerical results are compared with the existing ones in the literature and a good agreement is showed.

• Steel and Composite Structures
• /
• v.14 no.4
• /
• pp.313-333
• /
• 2013

The web-encased steel-concrete composite (WESCC) beam is a new developed steel-concrete composite beam. Experiments of six simply supported WESCC beam specimens were conducted. The effects of the shear-span ratio and steel section type were all investigated on the static behaviors such as failure modes, failure mechanism and bearing capacity. The experimental results denoted that all specimens failed in bending mode and the degree of combination between the bottom armor plate of steel shape and concrete were very well without any evident slippage, which demonstrated that the function of bottom armor plate and web were fully exerted in the WESCC beams. It could be concluded the WESCC beams have high stiffness, high load carrying capacity and advanced ductility. The design methods are proposed which mainly consist the bearing capacity calculation of bending and flexural rigidity. The calculation results of the bearing capacity and deflection which take the shear deflection into account are in agreement with the experimental results. The design methods are useful for design and application of the innovative composite beams.