• Journal of the Korea Concrete Institute
• /
• v.23 no.5
• /
• pp.683-692
• /
• 2011

In piloti-type low-rise RC residential buildings, severe damages have been usually concentrated at piloti stories under the earthquake. In this study, a piloti story was retrofitted by installation of buckling-restrained braces (BRB's) to increase strength and stiffness of piloti story and by application of fiber reinforced polymer (FRP) sheet on columns to avoid the brittle shear and axial failure of columns. To verify this retrofit performance, reversed cyclic lateral load tests were performed on 1:5 scale bare and retrofitted frames. The test results showed that yield strength (43.2 kN) appeared to be significantly larger than design value (30 kN) due to the increase of strength in the compression side, but the stiffness value (11.6 kN/mm) turned out to be approximately one-half of the design value (24.2 kN/mm). The reasons for this difference in stiffness were due to slippage at joint between the frame and the BRB's, displacement and rotation at footing. The energy absorption capacity of the retrofitted frame was 7.5 times larger than that of the bare frame. The change of the number of load cells under the footing from 2 to 1 reduced lateral stiffness from 11.6 kN/mm to 6 kN/mm, which was only three times larger than that of the bare frame (2.1 kN/mm).

• Journal of Animal Science and Technology
• /
• v.47 no.3
• /
• pp.447-456
• /
• 2005

This study was conducted to evaluate the effects of energy level of concentrate feed in finishing Hanwoo steers for 6 months before slaughter. Feeding trial was done with 2 treatment groups, IDN72 (72% of TDN in concentrate) and TDN74 (74 % of TDN in concentrate). The body weight (from 19 to 24 months) tended to be higher in TDN74 than in TDN72, but was not significant. Average daily gain of TDN74 was higher by 4.4 % in comparison to TDN72. There was no significant differences in concentrate, dry matter and TDN intake per I kg body weight gain between TDN72 and TDN74. And there was a tendency to improve crude protein intake per I kg body weight gain by increasing TDN content from 72 to 74 %. The dressing percentage tended to be higher in TDN74 than in TDN72, but was not significant. Salable meat percentage tended to be lower in TDN74 than in TDN72 because of higher body fat percentage in TDN74 than in TDN72. There were no significant differences in marbling score, meat color, fat color, carcass weight, rib-eye area and back fat thickness between TDN72 and TDN74. Significant differences were not found in shear value, cooking loss, water holding capacity or moisture and protein contents of longissimus dorsi (LD) muscles between TDN72 and TDN74. Fat content of LD muscles tend to be lower in TDN74 than in IDN72 but without any significance. There was a tendency to improve juiciness and taste by feeding IDN74 rather than TDN72. Especially, tenderness of TDN74 was increased by 7.4% in comparison to TDN72 (p < 0.05). Gross income from TDN74 was higher than TDN72 by 5% The results suggested that significant differences were not found in growth performance, feed conversion and carcass characteristics between TDN72 and TDN74. The results also show that more studies are required to clarify the energy level for finishing Hanwoo steers.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.29 no.5
• /
• pp.427-435
• /
• 2009

Cylindrical structures such as pipes and shafts are widely used in various industrial facilities. Recently, researches on magnetostrictive transduction of torsional waves have been actively reported for the nondestructive evaluation of those cylindrical structures. However, the existing magnetostrictive patch transducer has somewhat inconvenient and time.consuming process like patch bonding to a structure since it should employ a magnetostrictive patch having strong magnetostriction. To overcome these limitations of the existing transducer, in this work, we develop a novel modular magnetostrictive transducer to generate and measure torsional waves to inspect a cylindrical structure. The proposed transducer can be applied as viscous liquid coupling with shear couplant or dry coupling without coupling media instead of patch bonding to a structure. We describe a detailed structure of the modular transducer and conduct some experiments to verify its performance.

• Journal of Conservation Science
• /
• v.33 no.6
• /
• pp.467-483
• /
• 2017

In this study, the degradation properties by temperature stress of $Araldite^{(R)}$ rapid-curing epoxy resin used for inorganic cultural heritages, was identified. The tensile and tensile shear strength of durability decreased for 12,624 hours at temperatures of $40{\sim}60^{\circ}C$. In terms of stability of external stress and temperature, the slow-curing epoxy was superior to the rapid-curing epoxy, and cultural heritage conservation plans should therefore consider the strength and stress properties of restoration materials. Color differences increased for 12,624 hours at temperatures of $40{\sim}60^{\circ}C$, and glossiness decreased. Both color and gloss stability were weak, which necessitates the improvement of optical properties. Thermal properties (weight loss, decomposition temperature, and glass transition temperature) of adhesives are linked to mechanical properties. Interfacial properties of the adherend and water vapor transmission rates of adhesives are linked to performance variation. For porous media (ceramics, brick, and stone), isothermal and isohumid environments are important. For outdoor artifacts on display in museums, changes in physical properties by exposure to varying environmental conditions need to be minimized. These results can be used as baseline data in the study of the degradation velocity and lifetime prediction of rapid-curing epoxy resin for the restoration of cultural heritages.

• Journal of Biomedical Engineering Research
• /
• v.24 no.1
• /
• pp.37-44
• /
• 2003

This experimental study is aimed at evaluating the hydrodynamic performance of newly designed self-expandable graft stents under steady flow condition. Two graft stents with different coating materials and a bare TiNi metallic stent for comparison test were used in the experiment. Pressure variation and velocity distribution at the upstream and downstream of the stents were measured at flow rates of 5, 10, and 15 l/min, respectively. Pressure loss due to insertion of the stent increased with increasing flow rate exponentially as expected. At a flow rate of 15 l/min, pressure loss of Polyure-thane(PU)-coated graft stent was 6 times higher than that of TiNi metallic stent, while the pressure loss of a porous Polytetrafluoroethylene(PTFE)-coated graft stent was comparable to a bare TiNi metallic stent. Velocity profiles of the porous PTFE-coated graft stent were similar to those of a bare TiNi metallic stent regardless of flow rate. Furthermore, the velocity profile of PU-coated graft stent revealed an asymmetrical and relatively low central velocity at a higher flow rate than 10 1/min, expecially, where the effects resulted in increases of wall shear stress and normal stress. The worse hydrodynamic behavior of PU-coated graft stent than the other two stents might be attributed to formation of folds due to poor flexibility of coated material when inserting the graft stent into the pipe with a more smaller size, which later gave rise non-symmetry of flow area, increase of surface roughness and jet flow via the crevice between the stent and cylinder wall.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.18 no.6
• /
• pp.13-20
• /
• 2017

High-rise building shapes are changing from orthogonal to irregular form and the current trend is to arrange members in geometric grid-patterns at the perimeter of buildings. This study proposes a simple model for the preliminary design of a hexagrid high-rise building. The size of the cross section is set to be different at each module and hexagrid unit, which is different from the previous studies in which all hexagrid members were the same. To examine the effect of hexagrid size on structural performance, 60-story hexagrid buildings with 1-, 2- and 4-story high modules are designed and analyzed. Maximum lateral displacement, steel tonnage, load carrying percentage of perimeter frame and combined strength ratio are compared for 15 buildings. As the lateral load carrying capacity of hexagrid structure was inferior to a diagrid structural system, proper lateral stiffness should be allocated to the core frame in a hexagrid structure. The best ratio of flexural to shear deformation was 4 and larger unit size was better in considering constructional cost and structural efficiency. As the maximum lateral displacements of the buildings were within 84%~108% of the limit, the proposed method seems to be applicable to preliminary design of hexagrid buildings.

• Journal of Korean Tunnelling and Underground Space Association
• /
• v.7 no.2
• /
• pp.153-163
• /
• 2005

This paper presents two case studies for tunnelling in Bangkok: a subway tunnel site and a flood diversion tunnel site. The first case study is related to ground displacement response for dual tunnel Bangkok MRT subway. The MRT subway project of Bangkok city consists of dual tunnels about 20 km long with 18 subway stations. The tunnels are seated in the firm first stiff silty clay layer between 15-22 m in depth below ground surface. The behavior of ground deformation response based on instrumentation is presented. The back analysis based on plain strain FEM analysis is also presented and agrees with field performance. The shear strain of FEM analysis is in the range of 0.1-1% and in accordance with the results of self boring pressuremeter tests. Meanwhile, the second case study is related to the EPB tunnelling bored underneath through underground obstruction. The Premprachakorn flood diversion tunnel is the shortcut tunnel to divert the flood water in rainy season into the Choapraya river. The tunnel was bored by means of EPB shield tunnelling in very stiff silty clay layer at about 20-24 m in depth. During flood diversion tunnel bored underneath the existing Bangkok main water supply tunnel and pile foundation of the bridge, instrumentation was monitored and compared with predicted FEM analysis. The prevention risk potential by means of predicting damage assessment is also presented and discussed.

• Journal of Korean Tunnelling and Underground Space Association
• /
• v.21 no.6
• /
• pp.861-874
• /
• 2019

A great interest in the seismic performance evaluation of small size tunnel structures such as utility tunnel has been taken since recent earthquakes at Pohang and Gyeongju in Korea. In this study, the three-dimensional dynamic analyses of vertical shaft and horizontal tunnel under seismic load were carried out using FLAC3D. Especially, parametric analyses was performed to investigate the effects of interfacial stiffness on interfacial behavior between soil and structure. The parametric analysis showed that the interfacial stiffness scarcely gave an effect on the global dynamic behavior of the structure, while had a significant effect on the local displacement behavior of the connections. The magnitude of the interfacial stiffness was inversely proportional to the displacement, while the magnitude of interface stiffness was proportional to the normal and shear stresses. The results of this study suggest the limitations of the existing empirical equations for interfacial stiffness and emphasize the need to develop new interfacial stiffness models.

• Asian-Australasian Journal of Animal Sciences
• /
• v.21 no.12
• /
• pp.1745-1752
• /
• 2008

This study was conducted to compare the growth performance and carcass evaluation of Jeju native cattle (JNC) and its crossbreds (CBK = 25 JNC: 50 Charolais: 25 Brahman and BCBK = 62.5 JNC: 25 Charolais: 12.5 Brahman) fed for a short fattening period. Eight male calves each of JNC (80.$40{\pm}10$), CBK ($113.50{\pm}12.3$), and BCBK ($100.3{\pm}9.5$) were weaned at 4 month of age and were fed similar diets for 18 months of their age. All animals were fed a growing ration until 12 months of age and thereafter switched to a fattening ration for a period of 6 months. Final body weight (BW) and BW gain were significantly higher in CBK and BCBK compared with JNC. The CBK and BCBK gained 27.42% and 25.99% more BW, respectively, compared with JNC. The CBK and BCBK animals consumed significantly less DM than JNC to gain a unit of BW. Body weight gain, DM intake and feed conversion efficiency were similar between CBK and BCBK. Weight of hot and cold carcass, ribs, boneless meat and Longissimus dorsi muscle area were significantly different among JNC and its crossbreds. The heaviest carcass was observed in CBK followed by BCBK and JNC. Carcass, chest and femur lengths were greater in CBK and BCBK compared with JNC. Chest width, chest depth and hip width were similar in JNC and its crossbreds. Femur width was significantly greater in CBK compared with BCBK and JNC. Femur depth and chest girth were significantly greater in CBK and BCBK compared with JNC. Weight and fat yield in different carcass cuts were greater in crossbreds compared to JNC. Percent moisture, crude ash, and crude protein of meat were similar in JNC and its crossbreds. Percent crude fat in beef was significantly greater in JNC compared with its crossbreds. Beef shear force value, percent water holding capacity, juiciness and tenderness were significantly greater for JNC compared to its crossbreds. In conclusion, CBK and BCBK have shown greater growth rates and produced heavier carcasses with good degree of fatness when compared with JNC.

• Asian-Australasian Journal of Animal Sciences
• /
• v.22 no.8
• /
• pp.1195-1201
• /
• 2009

An experiment was conducted to evaluate the effects of dietary alpha-lipoic acid (LA) on growth performance, carcass characteristics and meat quality in Arbor Acres broilers. A total of 240 1-d-old male Arbor Acres broilers were randomly allocated to 4 dietary treatments (0, 300 ppm, 600 ppm, and 900 ppm dietary LA supplementation, respectively). Birds were slaughtered at 42 days old. Live body weight (BW), average daily gain (ADG), average feed intake (AFI), feed conversion ratio (FCR), dressing percentage, breast muscle percentage, thigh muscle percentage, abdominal fat percentage, muscle color (L*, a*, b*), pH values at 24 h postmortem, meat shear force value (SFV) and anti-oxidative ability were measured. Results showed that addition of 600 ppm or 900 ppm LA decreased BW (p<0.01), ADG (p<0.01) and AFI (p<0.05) compared with other diets. FCR was not affected by dietary LA content. LA had no marked effect on dressing percentage, breast muscle percentage or thigh muscle percentage. Abdominal fat percentage was lower (p<0.05) in the 900 ppm LA supplementation group than the control group. Dietary 900 ppm LA increased (p<0.05) breast and thigh muscle pH value at 24 h postmortem compared with the control treatment. Dietary LA increased thigh muscle a* value, though no significant difference was found in thigh muscle a* value among the treatments. Dietary LA significantly decreased breast muscle L* value (p<0.05), breast muscle b* value (p<0.01) and thigh muscle b* value (p<0.05). Broilers fed LA had higher breast muscle a* value (p<0.05) and thigh muscle L* value (p<0.05). All test groups had lower (p<0.05) breast muscle SFV than the control group. Dietary 600 ppm or 900 ppm LA both decreased (p<0.01) thigh muscle SFV compared with the control treatment. Dietary 900 ppm LA significantly increased (p<0.05) TAOC, SOD and GSHPx compared with no LA treatment. Broilers fed LA had lower (p<0.01) MDA compared with the control treatment. These results suggested that dietary LA enhanced the anti-oxidative ability and oxidative stability, and contributed to the improvement of meat quality in broilers.