• 한국공간구조학회논문집
• /
• 제14권2호
• /
• pp.79-86
• /
• 2014

The purpose of this study is intended to determine the validity of shear reinforcement by evaluating flexural performance in the hollow slab. The hollow slab is relatively light and second moment of inertia is large. Due to these characteristics, it can be used to slab system efficiently. Therefore the prediction of the structural behaviors is very important because of decrease of shear and flexural strength which is caused by hollow section of slab interior. In this study, the flexural test were performed to analyze the flexural capacity of the hollow slab w/ or w/o shear reinforcement. A total of six full scale specimens were tested. These specimens have three cases of reinforcing bar ratio, 0.009, 0.018 and 0.024. To verify the flexural behavior such as ultimate load, load-deflection and crack pattern, the flexural experiment were tested by using loading frame. Experimental results have shown that the flexural behavior are depend on the reinforcing bar ratio. Also the hollow slab with shear reinforcement have shown flexural behavior. Therefore, it is appropriate that the hollow slab is reinforced by shear reinforcement to improve the flexural performance of the hollow slab.

• Advances in concrete construction
• /
• 제9권4호
• /
• pp.413-421
• /
• 2020

For steel-concrete girders made composite using shear studs, initial damage on studs induced by weld defect, unexpected overloading, fatigue and others might degrade the service performance and even threaten the structural safety. This paper conducted a numerical study to investigate the static behavior of damaged stud shear connectors that were embedded in ultra high performance concrete (UHPC). Parameters included damage degree and damage location. The material nonlinear behavior was characterized by multi-linear stress-strain relationship and damage plasticity model. The results indicated that the shear strength was not sensitive to the damage degree when the damage occurred at 2/3d (d is the stud diameter) from the stud root. An increased stud area would be engaged in resisting shear force as the distance of damage location from stud root increased and the failure section becomes inclined, resulting in a less reduction in the shear strength and shear stiffness. The reduction factor was proposed to consider the degradation of the shear strength of the damaged stud. The reduction factor can be calculated using two approaches: a linear relationship and a square relationship with the damage degree corresponding to the shear strength dominated by the section area and the nominal diameter of the damaged stud. It was found that the proposed method is preferred to predict the shear strength of a stud with initial damage.

• 지질공학
• /
• 제3권1호
• /
• pp.1-20
• /
• 1993

본 연구에서는 절리면에서의 전단거동 특성을 규명하기 위해 총 37개의 편마암종 코아 시편들을 대상으로 Portable Direct Shear Box를 이용하여 실내 직접전단시험을 수행하였다. 시편들에 가해진 최대 수직응력의 범위는 $5.60~25.67kg/\textrm{cm}^2$이었으며, 전단하중을 점진적으로 가중시키는 다단계 전단시험법에 준하여 실험하였다. 이러한 방법에 의한 실험결과들을 분석하여 절리면의 전단강도에 관한 경험식들을 제시하였으며, 전단거동에 영향을 미치는 역학적 파라미터들을 도출하여 상호 비교 분석하였다. 절리조도계수에 따른 전단강성의 변화는 수직응력이 증가함에 따라 시편의 절리조도계수가 클수록 전단강성의 값도 급증하는 경향을 보이며, 본 실험에 적용한 최대 수직응력 하에서 구한 평균 할선 전단강성은 약 $110.68kg/\textrm{cm}^3$였다. 또한 수직응력이 증가함에 따라 시편의 깅이와 전단강성 사이에는 크기효과(size effect)에 의한 반비례 관계를 나타내어, 동일한 절리조도계수를 지닌 시편일지라도 길이가 긴 시편의 경우에 전단강성이 감소함을 알 수 있었다.

• 콘크리트학회지
• /
• 제7권5호
• /
• pp.179-188
• /
• 1995

강섬유보강콘크리트는 콘크리트의 취성을 극복하고 콘크리트 내의 강섬유의 구속작용과 균열제어메카니즘, pull-out저항 등에 의하여 강도가 증진되며 이러한 작용에 의하여 전단하중하에서도 강도와 연성의 증대를 가져온다. 강섬유보강콘크리트의 2차적인 보강효과는 휨보다는 전단거동에 대하여 더 효율적인 것으로 보고되고 있다. 따라서 시멘트계 재료에 훅트강섬유를 혼입함으로써 전단하중 하에서 훅트강섬유보강 철근콘크리트보(RHSFCB)의 전단저항력이 증가되고 결과적으로 보의 구조적 거동과 전단강도가 향상된다. 본 연구에서는 RHSFCB의 전단거동에 영향을 미치는 주요 변수들에 대한 각 영향을 실험적으로 고찰하였으며, 본 연구에서 고찰한 주요변수는 섬유혼입율, 전단-스팬비, 스터럽의 간격등이다. 이론적 고찰은 문헌에 보고된 각 전단강도 예측식들에 본 실험에서 전단파괴한 9개 시험체와 문헌에 나타난 86개의 전단파괴시험체를 적용하여 각 예측식들의 전단강도를 비교하였으며, 그 결과치를 통계분석하여전단강도예측식의 정확성을 고찰하였다.

• Journal of the Korean Wood Science and Technology
• /
• 제30권4호
• /
• pp.96-105
• /
• 2002

전단벽은 현대식 경골목조건축에서 바람이나 지진 등에 의한 측방하중에 대한 저항력을 제공하는 가장 중요한 요소 중의 하나이다. 전단벽에서 건물에 전달된 측방하중은 벽의 스터드와 덮개재료 사이의 못접합부를 통하여 덮개재료로 전달되고 덮개재료에 전달된 하중은 판재의 면전단력에 의하여 지지된다. 따라서 실제 전단벽에서 측방하중에 대한 저항력을 결정하는 가장 중요한 요소는 못접합부라고 할 수 있을 것이다. 이 연구에서는 스터드와 판재 사이의 못접합부에 대한 강성 및 강도를 측정하였으며 이 값들은 전단벽의 찌그러짐 저항력을 예측하는 이론모형의 입력자료로 사용되었다. 이론모형의 예측치의 정확성을 검증하기 위하여 판재 한 장으로 구성된 전단벽의 전단시험을 수행하였다. 못접합부의 강성은 스터드 부재의 섬유방향에 의하여 영향을 받았으나 판재의 방향은 거의 영향을 미치지 않는 것으로 나타났다. 전단하중 하에서 못접합부나 전단벽의 거동은 3개의 직선구간으로 나나낼 수 있었으며 이론모형 I보다 이론모형 II의 예측치가 더 정확하였다.

• 한국지반공학회논문집
• /
• 제24권6호
• /
• pp.69-75
• /
• 2008

분리형부재 보강토 옹벽(SRW)을 구성하는 생태축조블록 접촉면에 대한 전단시험을 수행하였다. 전단이 발생하는 두 개의 블록 사이의 접촉면조건은 두 블록을 직접 접촉시키는 경우와 블록 사이에 고무패드를 설치한 경우 그리고 블록 사이에 고무패드와 전단키를 설치한 각각 3가지 접촉면 조건을 고려하였다. 전단시험에 따르면 두개의 블록을 직접 접촉시킨 경우 전단하중-전단변위 관계가 탄성-완전소성형태와 유사하였으며 블록 사이의 접촉면에 고무패드를 설치한 경우 전단하중-전단변위 관계는 연성거동을 보였다. 블록과 블록을 직접 접촉시킨 경우와 블록과 블록 사이의 접촉면에 고무패드를 설치한 경우 그리고 블록과 블록 접촉면 사이에 고무패드와 전단키를 설치한 경우에 대한 최소 전단저항력과 겉보기 마찰각은 각각 1.7kN/m, $27.6^{\circ}$와 4.2kN/m, $26.2^{\circ}$ 그리고 20.9kN/m, $26.0^{\circ}$이었다.

• Nuclear Engineering and Technology
• /
• 제56권6호
• /
• pp.2352-2366
• /
• 2024

Reinforced concrete (RC) shear walls with precast steel-concrete composite modular (PSCCM) are strongly recommended in the structural design of nuclear power plants due to the need for a large number of process pipeline crossings and industrial construction. However, the effect of the PSCCM on the mechanical behavior of the whole RC shear wall is still unknown and has received little attention. In this study, three 1:3 scaled specimens, one traditional shear wall specimen (TW) and two shear wall specimens with the PSCCM (PW1, PW2), were designed and investigated under cyclic loadings. The failure mode, hysteretic curve, energy dissipation, stiffness and strength degradations were then comparatively investigated to reveal the effect of the PSCCM. Furthermore, numerical models of the RC shear wall with different PSCCM distributions were analyzed. The results show that the shear wall with the PSCCM has comparable mechanical properties with the traditional shear wall, which can be further improved by adding reinforced concrete constraints on both sides of the shear wall. The accumulated energy dissipation of the PW2 is higher than that of the TW and PW1 by 98.7 % and 60.0 %. The failure of the shear wall with the PSCCM is mainly concentrated in the reinforced concrete wall below the PSCCM, while the PSCCM maintains an elastic working state as a whole. Shear walls with the PSCCM arranged in the high stress zone will have a higher load-bearing capacity and lateral stiffness, but will suffer a higher risk of failure. The PSCCM in the low stress zone is always in an elastic working state.

• Geomechanics and Engineering
• /
• 제5권6호
• /
• pp.499-517
• /
• 2013

In order to investigate shear behavior of granular materials due to excavation and associated unloading actions, load-controlled plane strain compression tests under decreasing confining pressure were performed under drained conditions and the results were compared with the conventional plane strain compression tests. Four types of granular material consisting of two quartz sands and two glass beads were used to investigate particle shape effects. It is clarified that macro stress-strain behavior is more easily influenced by stress level and stress path in sands than in glass beads. Development of localized deformation was analyzed using photogrammetry method. It was found that shear bands are generated before peak strength and shear band patterns vary during the whole shearing process. Under the same test condition, shear band thickness in the two sands was smaller than that in one type of glass beads even if the materials have almost the same mean particle size. Shear band thickness also decreased with increase of confining pressure regardless of particle shape or size. Local maximum shear strain inside shear band grew approximately linearly with global axial strain from onset of shear band to the end of softening. The growth rate is found related to shear band thickness. The wider shear band, the relatively lower the growth rate. Finally, observed shear band inclination angles were compared with classical Coulomb and Roscoe solutions and different results were found for sands and glass beads.

• 한국공간구조학회논문집
• /
• 제21권3호
• /
• pp.35-42
• /
• 2021

An experimental study was carried out to evaluate the shear performance at the interface composed of structural laminates and concrete. The main variables are the number of CLT layers and the shape of the shear connector. The number of CLT layers consisted of 3 and 5 layers. A total of 6 test specimens for shear performance evaluation were prepared in the form of a shear connector, a direct screw type and a vertically embedded type. As a result of the experiment, similar behavior was shown in all specimens, regardless of the number of layers, including direct screw type (SC series) and vertically embedded type (VE series). The behavior at the joint surface was damaged due to the occurrence of initial shear cracks, expansion of shear groove cracks, and splaying at the interface after the maximum load.After the maximum load, the shear strength decreased gradually due to the effect of the shear connector. It can be seen that the shear strength of all specimens is determined by shear and compression stress failure of concrete at the interface of the notch joint.

• 한국지진공학회논문집
• /
• 제25권1호
• /
• pp.1-9
• /
• 2021

Most commercial buildings among existing RC buildings in Korea have a multi-story wall-frame structure where RC shear wall is commonly used as its core at stairways or elevators. The members of the existing middle and low-rise wall-frame buildings are likely arranged in ordinary details considering building occupancy, and the importance and difficulty of member design. This is because there are few limitations, considerations, and financial burdens on the code for designing members with ordinary details. Compared with the intermediate or unique details, the ductility and overstrength are insufficient. Furthermore, the behavior of the member can be shear-dominated. Since shear failure in vertical members can cause a collapse of the entire structure, nonlinear characteristics such as shear strength and stiffness deterioration should be adequately reflected in the analysis model. With this background, an 8-story RC wall-frame building was designed as a building frame system with ordinary shear walls, and the effect of reflecting the shear failure mode of columns and walls on the collapse mechanism was investigated. As a result, the shear failure mode effect on the collapse mechanism was evident in walls, not columns. Consequently, it is recommended that the shear behavior characteristics of walls are explicitly considered in the analysis of wall-frame buildings with ordinary details.