• 소성∙가공
• /
• 제8권1호
• /
• pp.14-21
• /
• 1999

Trapezoid cups and square ones have been deep-drawn to 45mm in depth. Displacements and strains have been analysed by FEM and experiment. Strains and effective strains in the corner flanges of trapezoid cups have been compared with those in square cups. The results have shown that because of shear strains on the corner flange, it is necessary to adopt effective strain for comparing strains, mean vale of effective strains in the corner flange with a corner angle of 72 degrees is narly equal to those with a corner angle of a right angle and mean value of effective strains with a corner angle of 102 degrees is smaller than those with a corner angle of a right angle.

• 한국정밀공학회지
• /
• 제16권2호통권95호
• /
• pp.31-38
• /
• 1999

Square cups have been drawn to 20mm~60mm in depth and displacements and strains have been analysed by FEM and experiment. Displacements and strains on the corner flange of square cups have been compared with those of cylindrical cups. The results have shown that shear strains take place on corner flanges of square cups, it is necessary to adopt effective strain for comparing of stains and the effective strains on the corner flange in square cups are smaller than those in cylindrical ones.

• 한국세라믹학회지
• /
• 제32권1호
• /
• pp.17-24
• /
• 1995

The TEA complex polymeric sol was prepared by the alkoxide sol-gel method. The purpsoe of this experiment was to vefity the particle shape in the sol from the investigation of the rheological properties. TEA retarded hydrolysis rate by the reaction with alkoxide enough to make a stable transparent sol in the wide range of composition. From the results of the viscosity change with time, the optimum mole ratio for spinning was selected as 0.5 mole of TEA, 3 mole of H2O and the optimum viscosity was 104 cPs. The rheological behavior of the sol showed that the particle shape in the sol was linear, which was adequate for fiber drawing.

• 한국인쇄학회지
• /
• 제25권1호
• /
• pp.95-107
• /
• 2007

This study starts to find a way out, experiment and apply commercial UV coatings to the cap closures. The cap closures is made form coating and succeeding deformation process. It is coated with several printing layers, printing and over print varnish coating. Then it pressed in three steps of press called 'deep-drawing'. In this study, two kinds of coating was designed and accomplished in the base of the same manufacturing and environment conditions. Consequently, UV curable ink have adequate performance in this experiment (T-bending, Erichsen Test), but it were experienced several damages in this experiments (web-bending, impact test). They were not cured enough to endure the friction and a unique shape of serial cracks were appeared.

• 한국산학기술학회논문지
• /
• 제18권6호
• /
• pp.692-696
• /
• 2017

프레스 부품의 형상은 고객 요구와 공정단축 및 비용절감으로 점점 복잡하게 변하고 있다. 또한 프레스공정은 많은 인자의 영향으로 양산 중에도 안정성이 수시로 변하고 있다. 공정의 안정성을 확보하는 데는 형상, 소재, 프레스, 금형 및 윤활에 대한 사전 연구가 충분히 되어 허용된 공차 안에서 재현성이 구현되는 공정을 수립해야 한다. 하지만 예측하지 못한 공정인자들의 변화는 양산라인 정지와 생산계획에 차질을 현장에서 야기 시키고 있다. 이에 프레스금형에 센서를 적용해 실시간 공정을 모니터링 할 수 있는 방법을 본 논문에선 소개한다. 비접촉식으로 판재의 흐름을 측정하는 센서와 그 중 양산에 적용 가능성이 높은 광학센서를 사용한 실험 사례를 제시했다. 원통드로잉금형에 광학센서를 설치해 소재, 블랭크홀더힘, 드로잉비를 변화시키며 센서의 사용 가능성을 테스트했다. 또한 각통드로잉 금형을 사용해 국부적으로 다른 판재의 흐름을 정량화 했고 측정값이 소재의 연신에 의해 드로잉 깊이보다 항상 작다는 것을 정량적으로 측정하였다. 마지막으로 프레스 금형에 센서를 접목시켜 사용할 수 있는 분야에 대해 제안을 하였다. 원가절감에 대한 Needs가 지속적으로 증가하고 이를 통해 글로벌 금형경쟁력을 확보해야하는 시점에 기여가 되었으면 한다.

• 한국농공학회지
• /
• 제19권2호
• /
• pp.4417-4422
• /
• 1977

This thesis is a result of theoretical and electrical experimental studies for the shape of Seepage on various Earth Dams. The decrement method of seepage through of water amount to earth Dam's was tested by means of experiment by the model constructed in the water tank. A study of the seepage through earth Dam's is necessary for a satisfactory of the same. An attempt was made in these investigations to study the problem of the seepage through homogeneous earth dams with filters located near the axis of the dam and filters extending in to upstream portion of the dam by the electrical analogy method. The experimental results were at variance with the graphical solution given by A Casagrande method. Some of the results were checked by relaxation method and by the circle criterion for drawing flow nets.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2002년도 추계학술대회 논문집
• /
• pp.641-645
• /
• 2002

In case of aluminum-cased battery, The ratio of height and base of square is generally above the ten times, square-shaped and problem of non-axis symmetry. It is typical model to set up the analysis method of finite element. The reliable analysis of finite element method is suggested, which is used to investigate the possibility that multi-stage deep drawing and ironing used currently is replaced by backward impact extrusion favorable in the respect of cost production and productivity. The influence of parameter was analyzed and compared, which was considered to analyze the process of large deformation plasticity such as extrusion. Die and billet was made as the same shape of finite element model. The results of experiment show good forming without the rupture and wrinkles with the optimum velocity 100mm/sec obtained by analysis.

• 열처리공학회지
• /
• 제21권4호
• /
• pp.183-188
• /
• 2008

Hot press forming allows geometrically complicated parts to be formed from sheet and the rapid cooling hardens them to extremely high strength. The main purpose of this research is to characterize Al coated layer in Al coated boron steel during hot press forming. For the hot press hardening experiment, test specimens were heated up to $810{\sim}930^{\circ}C$ and held for 3, 6 and 9 minutes, respectively. And then, some specimens were press hardened and others were air-cooled without any pressing for the comparison purpose. Al coated layer shows four distinct micro-structural regions of interest; diffusion zone, Al-Fe zone(I) low-Al zone(LAZ) and Al-Fe zone(II). Band-like LAZ is clearly shown at temperature ranges of $810{\sim}870^{\circ}C$ and sparsely dispersed at temperature higher than 900oC. The micro-cracking behavior in the Al coated layer during forming were also analyzed by bending and deep drawing tests. The strain concentration in softer LAZ is found to be closely related with micro-cracking and exfoliation in coated layer during forming.

• 복식문화연구
• /
• 제1권2호
• /
• pp.131-144
• /
• 1993

Even though it has been to research on the variance of clothing pressure and on its effect of human body, it has not been available to evaluate the clothing pressure as an objective standard ta for the determination of an extra quantity of bodice' basic pattern. In this paper the basic pattern(the close adherence original shape) is determined by a drawing of plane figure after detaching an unweaving clothing from the inside of the gypsum, and the extra quantity is figured by a extension quantity when is formatted with 0.5, 1.0, 1.5 cm extra quantity longitudinal-cross section figures. With our experimental method, review the variance of clothing pressure according to difference of the extra quantity which was figured with subjects wearing experimental clothing including the extra quantity. The difference of the extra quantity was able to calculate with data form the subjects when anatomical position and five movements, then compare with subjects wearing non-extra quantity experimental clothing. The results of experiment as the follows : 1. There is only few body portions with the significant variance according to the increasing of he extra quantity at he body portion and the sleeve portion. 2. The clothing pressure of the sleeve portion was higher than the clothing pressure of the body portion. The difference of clothing pressure according to the variance of the extra quantity at the sleeve portion is more significant than the body portion. 3. Consider several important pressure points which wil be the No. 1 at the front of body portion. No. 17, 18 at the back of body portion and No. 21 at the sleeve portion. 4. It is important to have plane figure of gypsum when format an basis pattern.

• 한국해양공학회지
• /
• 제21권4호
• /
• pp.21-27
• /
• 2007

The multiplication equipment of marine products with artificial upwelling structures could be useful in the fishing grounds near coastal areas. Artificial upwelling structures could move the inorganic nutrients from the bottom to the surface. Artificial upwelling structures have been used to improve the productivity of fishing grounds. Until now, research on artificial upwelling structures has been related to the distribution of the upwelling region, upwelling structures, and the marine environment. However, little work on the optimum design of the rubber-mound artificial upwelling structures has been done to increase the efficiency of drawing up the inorganic nutrients. This study investigated the optimum cross-section of rubber-mound artificial upwelling structures by means of hydraulic experiments. The hydraulic experiments include the falling test of rubber. Based on the results of the falling test, the relationship between the length of the rubber mound and water velocity, and the relationship between the shape of the rubber and the stratification parameter were established. In addition, the effect of the void ratio of various artificial structures on the stratification parameter was studied. From the experiment, it was found that upwelling could be enhanced when the ratio of structure height to water depth was 0.3 and stratification parameter was 3.0. The upwelling was not improved when the void ratio exceeded 0.43. The optimum size of rubber mounds was determined when the incident velocity was influenced by the mean horizontal length rather than size of block.