• Tribology and Lubricants
• /
• v.10 no.1
• /
• pp.62-68
• /
• 1994

The analysis of statically indeterminate bearing-shaft system was investigated. The moment loads and misalignment angles which were induced in the ball bearings were determined, and the influence of span length of this system on the moment loads and fatigue lives was identified. The sliding and spinning speeds between balls and raceways which affected the performance of ball bearing evaluated. The equation to estimate the cage speed of ball bearing under moment loads was proposed. This equation had been verified by the test results of measuring of cage speed, which was useful to the prediction of ball bearing under moment loads.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2008.03a
• /
• pp.778-783
• /
• 2008

In this paper, numerical method was calculated on evaluation of underground ventilation system to keep servicing a fresh air. The tunnel length for simulation is 18.2 km with various located seven ventilation shaft. Generally, owing to thermal generation in cable tunnel under about 50 m depths, cable tunnel ventilation system is more important than that of other tunnels. So, we conducted that the effects of ventilation systems was simulated depending on the difference of electrical power tunnel length, the number of shaft tunnel, forced ventilation and duct was or not. Test results show that the main conditions in order to enhance the underground cable tunnel are that ventilation systems have to be designed with forced ventilation and with duct.

• KIEE International Transaction on Electrical Machinery and Energy Conversion Systems
• /
• v.11B no.2
• /
• pp.9-14
• /
• 2001

Because salient pole rotor type single phase SRM(Switched Reluctance Motor) has a simple structure and can be use both radial and axial direction magnetic flux at the same time, its output power per unit volume is high. Therefore, the shaft length can be minimized when compared with same output motors. However, salient pole rotor is hard to design due to its complex magnetic circuit. In this paper, salient pole rotor type single phase SRM with minimized shaft length is designed and selected the most suitable dimension of rotor, stator, pole arc and salient pole.

• Journal of the Korean Geotechnical Society
• /
• v.20 no.6
• /
• pp.29-40
• /
• 2004

The bearing capacity of drilled shaft is affected by several factors, such as shaft length, shape, surface roughness, young's modulus of geomaterials and shaft, soil strength, confining stress and so on. However, there has been no design method of drilled shaft considering all factors mentioned above. Moreover, since geomaterials are simply classified as sand, clay and rock, there was no design criterion for IGM (Intermediate Geomaterials). Therefore, the rigorous design approach of drilled shaft was not possible by classical design method. However, since these characteristics were not considered in classical theories, bearing capacity was generally different ken practical value. In this study, the bearing capacity of drilled shaft with the IGM's theory was compared with those of classical theories. The results showed that classical method showed smaller values of bearing capacity than those of field load transfer data. Moreover, the evaluated value of bearing capacity with IGM theory corresponded fairly well with those of field data.

• Tunnel and Underground Space
• /
• v.13 no.3
• /
• pp.196-206
• /
• 2003

In order to investigate the workability of Raise Boring Machine(RBM) such as utilization, penetration rate and advance rate, a vertical shaft of 98 m in length and 3.05 m in diameter was constructed in the layer of conglomerate by using the RBM in this study. In addition, field data from tow different construction sites including water-pump power plant tunnel, roadway tunnel and mining tunnel by RBM were collected and analyzed. The results show that the average weekly bored length is 19.3 m and its average utilization is between 54.3 % and 75.1 % very higher than that of the TBM(Tunnel Boring Machine). It also turns out that the bit force increases linearly with respect to the increase of the RPM(revolution per minute) of RBM. However, the net penetration rate decreases with the increase of bit force, RPM of RBM and depth of shaft. The findings of this study can be used to provide the useful information for the design of shaft and the selection of RBM.

• The KSFM Journal of Fluid Machinery
• /
• v.2 no.2 s.3
• /
• pp.32-38
• /
• 1999

An experimental study is performed to investigate the frequency effects of the excitation force on the linear stiffness and damping coefficients of a LOP (load on pad) type five-pad tilting pad journal bearing with the diameter of 300.91 mm and the length of 149.80 mm. The main parameter of interest in the present work is excitation frequency to shake the test bearing. The excitation frequency is controlled independently, using orthogonally mounted hydraulic exciters. The relative movement between the bearing and shaft, and the acceleration of the bearing casing are measured as a function of excitation frequency using the different values of bearing load and shaft speed. Measurements show that the variation of excitation frequency has quite a little effect on both stiffness and damping coefficients. Both direct stiffness and damping coefficients in the direction of bearing load decrease by the increase of shaft speed, but increase with the bearing load.

• 유체기계공업학회:학술대회논문집
• /
• 1998.12a
• /
• pp.173-179
• /
• 1998

An experimental study is performed to investigate the frequency effects of the excitation force on the linear stiffness and damping coefficients of a LOP (load on pad) type five-pad tilting pad journal bearing with the diameter of 300.91 mm and the length of 149.80 mm. The main parameter of interest in the present work is excitation frequency to shake the test bearing. The excitation frequency is controlled independently, using orthogonally mounted hydraulic exciters. The relative movement between the bearing and shaft, and the acceleration of the bearing casing are measured as a function of excitation frequency using the different values of bearing load and shaft speed. Measurements show that the variation of excitation frequency has quite a little effect on both stiffness and damping coefficients. Both direct stiffness and damping coefficients in the direction of bearing load decrease by the increase of shaft speed, but increase with the bearing load.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.25 no.11
• /
• pp.1767-1776
• /
• 2001

For the stable operation of high speed air spindle, the low rotational inertia and high damping ratio of spindle shafts as well as high fundamental natural frequency are indispensable. Conventional steel spindles are net appropriate for very high speed operation because of their high rotational inertia and low damping ratio. In this study, a high speed spindle composed of carbon fiber epoxy composite shaft and steel flange was designed for maximum critical speed considering minimum static deflection and radial expansion due to bending load and centrifugal force during high speed relation. The stacking angle and the stacking thickness of the composite shaft and the adhesive bonding length of the 7teel flange were selected through vibrational analysis considering static and thermal loads due to temperature rise.

• Journal of the Korean Orthopaedic Association
• /
• v.52 no.1
• /
• pp.7-14
• /
• 2017

Purpose: To report the clinical results from surgical treatment for clavicle shaft fracture by percutaneous intramedullary fixation with Steinmann pins. Materials and Methods: Between January 2004 and June 2014, the medical records of 135 patients who underwent percutaneous intramedullary fixation with Steinmann pins were reviewed. The mean follow-up periods were 15 months. The functional results were evaluated with The Disabilities of the Arm, Shoulder and Hand (DASH) score and Constant score. The clinical results were evaluated with the shortened length of the clavicle, length of surgical wound, operation time and Kang's criteria. Results: The mean bone union period was 11.6 weeks (8-16 weeks). The mean DASH score was 11.8. The mean Constant score was 91.2. The mean shortened length of the clavicle was less than 20 mm. The mean length of surgical wound was 1.2 cm (0.7-1.5 cm). The mean operation time was 18 minutes (10-35 minutes). Using Kang's criteria, 131 out of 135 patients (97.0%) showed good results. Complications included were 3 pin migrations and 2 non-unions. Conclusion: Percutaneous intramedullary fixation with Steinmann pins showed good results for treating clavicle shaft fracture.

• Journal of Advanced Marine Engineering and Technology
• /
• v.29 no.7
• /
• pp.713-721
• /
• 2005

A marine diesel engine should realize optimal operation efficiency while reducing NOx, PM (Particulate Matters) and other emissions. Fuel injection systems that use electronic control can become an effective means of achieving that objective. However. it still needs some accurate and instant information in order to bring its ability into full potential while sailing on the sea. The important information of them are a shaft torque and continuous combustion pressures of all cylinders. The shaft torque and the propeller thrust described in this paper are measured at an intermediate shaft by using a unique principle that one of two electromagnet coils oscillates a vibrating strip which the length changes with force and the other coil picks up the change of the frequency of the vibrating strip. For further reference, the shaft power meter multiplied the torque by the shaft revolution has already had about 750 sets of sales performance. The research presented in this paper started about ten years ago and is concerned with the development of a combustion pressure sensor that uses the same principle. Recently, the pressure sensor which bears continuous operation has been developed after a hard struggle, that is, the system that consists of a shaft horsepower meter, a propeller thrust meter and a combustion pressure sensor has been completed and has been shown to be reliable. This paper describes the configuration of this system, the material of the combustion pressure sensor, the principle of that, and the improving point of the sensor, and, we finally consider the use of this system.