• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 1998년도 춘계학술대회 논문집
• /
• pp.117-122
• /
• 1998

The misalignment state causes some problems in operating. These problems such as vibration, noise, make the reduce wear, as well as, a stress concentration on the coupling which is the very weakness point at the morter. In order to align the shaft, the dialgage method has used as a means of solution until now. The method using a dialgage require a great deal of labour and money due to making by hand, the accurate alignment is not up to the expectation. For aligning the shaft, all the rotor must come to accord. Also, the dialgage method cannot be compared with straingage measurement method, from the viewpoint, which can gage in short time.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2000년도 춘계학술대회논문집B
• /
• pp.886-891
• /
• 2000

One of the domestic co-generation plants have undergone excessive vibration problems of turbine attributed to external force for years. The root cause of turbine vibration may be shan alignment problem which sometimes is changed by thermal expansion and external farce, even if turbine technicians perfectly performed it. To evaluate the alignment condition from plant start-up to full load, a strain measurement of turbine and main steam piping subjected to thermal loading is monitored by using strain gages. The strain gages are bonded on both bearing housing adjusting bolts and pipe stoppers which. installed in the x-direction of left-side main steam piping near the turbine inlet in order to monitor closely the effect of turbine under thermal deformation of turbine casing and main steam piping during plant full load. Also in situ load of constant support hangers in main steam piping system is measured by strain gages and its results are used to rebalance the hanger rod load. Consequently, the experimental stress analysis by using strain gages turns out to be very useful tool to diagnose the trouble and failures of not only to stationary components but to rotating machinery in power plants.

• 해양환경안전학회지
• /
• 제24권4호
• /
• pp.482-488
• /
• 2018

선박 축계는 프로펠러 하중의 영향으로 선미관 후부베어링의 국부하중 증가가 현저히 나타나 축계 선미관 베어링 손상의 위험이 증대된다. 이를 방지하기 위해 수행된 추진축계 정렬연구는 주로 준정적 상태(quasi-static condition)에서 축과 지지베어링간의 상대적 경사각을 감소시키는데 중점을 두어 진행되어 왔다. 그러나 보다 상세한 평가를 위해서는 동적상태를 추가로 고려하는 것이 필요하다. 4,700 DWT 선박을 대상으로 NCR로 운전중 급속으로 우현 전타할 때 추진축계가 받는 영향에 대해 연구하였다. 연구결과 선미 유동장 변화에 의해 프로펠러 편심추력이 과도 상태가 되어 프로펠러에 불평형 진동이 유발되는 것을 확인하였다. 우현 전타시의 프로펠러 편심추력은 NCR 조건대비 축을 선미관 베어링으로부터 들어 올리는 힘으로 작용하여 선미관 베어링 하중완화에 기여하고 있음을 확인하였다.

• 대한족부족관절학회지
• /
• 제18권2호
• /
• pp.43-47
• /
• 2014

Hallux valgus is a lateral deviation of the first phalanx and medial deviation of the first metatarsal at the first metatarsophalangeal (MP) joint. Its incidence has increased due to developing footwear. The etiologies include fashion footwear, genetic causes, anatomical abnormality around the foot, rheumatoid arthritis, and neuromuscular disorders. Physiologic alignment of the first MP joint is maintained by congruent and symmetric alignment of the articular surface of the first proximal phalanx and first metatarsal head, physiologic relationship of the distal first metatarsal articular surface and the first metatarsal shaft axis, and stable balance of soft tissue around the first MP joint and stable tarsometatarsal joint. Several factors have been associated with hallux valgus, including pes planus, hypermobility of the first tarsometatarsal joint, flattened shape of the first metatarsal head, increased distal metatarsal articular angle, and deformation of the medial capsular integrity. History and physical examination are very important to diagnosis of hallux valgus. Simple radiography provides information on deformity, particularly in weight-bearing anteroposterior and lateral radiographs. Understanding the etiologies and pathophysiology is very important for success in treatment of patients with hallux valgus.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2007년도 춘계학술대회논문집
• /
• pp.411-415
• /
• 2007

The reduction of airborne and structure-borne noise of a shipboard pump for a navel ship is very important because the noise levels of the pump must not exceed criteria such as MIL-STD. In this paper, several practical examples of reducing the noise levels are presented. The examples show that the inadequate rotor-balancing and shaft-alignment results in the increase of the structure-borne noise on all lower mounts. It is also found that the unequal loading on mounts can cause the dramatically increasing the noise levels on certain local positions. Since the piping system arrangement such as valve location, flexible joint, and elbow location affects on the noise measurement, care must be taken to minimize the unnecessary noise from the piping system.

• 한국마린엔지니어링학회:학술대회논문집
• /
• 한국마린엔지니어링학회 2006년도 전기학술대회논문집
• /
• pp.1-2
• /
• 2006

선체 변형에 의해 발생할 수 있는 베어링 손상을 최소화하기 위해서는 설계 단계에서 선체 변형을 고려한 축계 배치 해석이 이루어져야 한다. 선체 변형은 유한 요소법을 이용한 구조해석에 의한 방법과 측정 데이터를 이용한 역분석 방법으로 구할 수 있다. 이 연구에서는 측정에 의해 얻어진 베어링 반력과 축의 굽힘 모멘트를 이용하여 선체 변형을 구하는 방법에 대해 설명하고, 이를 4만6천톤급 석유/화학운반선에 적용하여 다른 운전 조건에 대한 베어링 옵셋 변화와 선체 변형량을 검토한다.

• Tribology and Lubricants
• /
• 제36권2호
• /
• pp.82-87
• /
• 2020

In thrust bearings, the thrust collar and bearing surface need to be parallel to each other to ensure that all pads share the same load. In rotating machines, the shaft system cannot achieve perfect alignment. Misalignment of the thrust collar results in some pads supporting a higher load than others and excessive loads being placed on some pads. Consequently, high loads and high temperatures may occur in the bearing. Thus, in this study, we aim to analytically evaluate the performance of a misaligned non-equalizing direct lubricated tilting pad thrust bearing. We define the oil film thickness of the misaligned thrust bearing using the Byrant angle. Additionally, we calculate the pressure distribution and temperature distribution of the thrust bearing using the generalized Reynolds equation and energy equation. The design limit of the thrust bearing is defined by the load and temperature. Therefore, we evaluate the allowable misalignment angle as the limit of the maximum load and temperature. The analysis results demonstrate that an increase in the speed and load corresponds to a smaller allowable misalignment angle. However, as this is not the same for all thrust bearings, evaluating the allowable misalignment angle at each thrust bearing is essential.

• 전력전자학회논문지
• /
• 제27권6호
• /
• pp.481-488
• /
• 2022

This study proposes compensation methods for the initial position error and torque ripple in vector control of two-phase hybrid stepping motors. Stepping motors have an asymmetrical structure due to misalignment, such as the eccentricity generated by the manufacturing and assembly process. When vector control is applied using the position information measured by an incremental encoder attached to the rotor shaft of such stepping motors, the following problems occur. First, an initial position error occurs during the forced excitation process for the initial rotor position alignment. Second, torque ripple corresponding to the mechanical rotation frequency is generated. In this study, these non-ideal phenomena that occur in vector control of the stepping motor are analyzed, and compensation methods are proposed to eliminate them. The validity of the proposed initial position error and torque ripple compensation methods is verified through experiments on a two-phase hybrid stepping motor drive system.

• 대한족부족관절학회지
• /
• 제10권1호
• /
• pp.56-59
• /
• 2006

Purpose: The purpose of this study is to find out the normal distal tibial articular surface angle in coronal plane in Koreans. This would be helpful as the basic data for ankle reconstruction after trauma or deformity correction. Materials and Methods: Weight bearing anteroposterior radiographs of 123 normal ankles were reviewed. A line parallel to the shaft of the tibia was made. Another line was drawn parallel to the articular surface of the distal tibia. The superolateral angle that subtended by these two lines was measured. Results: There were 72 males and 51 females. The mean age overall was 35.7 years old. The mean age for males was 31.9 ($28{\sim}36$) years old. The mean age for females was 41.1 ($37{\sim}45$) years old. The mean distal tibial articular surface angle was $90.8^{\circ}$. The mean distal tibial articular surface angle for males was $91.5^{\circ}$ and for females $89.9^{\circ}$. Conclusion: The mean distal tibial articular surface angle in coronal plane for Koreans is $90.8^{\circ}$. We can avoid the error of the varization at the ankle alignment when the correction was performed vertical or minimal valgus to tibia tuberosity axis in Korean people.

• 플랜트 저널
• /
• 제4권3호
• /
• pp.66-72
• /
• 2008

The vibration of steam turbine is caused by Mass unbalance, Shaft misalignment, Oil whip and rubbing etc. But in turbine which is normally operated and maintained, the Mass unbalance component possesses the greatest portion. Our power plant has two steam turbines in capacity of 200 MW and 135 MW respectively and each turbine is supported by 6 journal bearings. However, we had many difficulties because the vibration amplitude of #3 and #4 Bearings was high during the start-up and operation mode change of steam turbine. But, with this study, we completely solved the vibration problem caused by the mass unbalance of #1 steam turbine. Until a recent date, #3 and #4 bearings which support high pressure turbine for #1 steam turbine had shown about $135{\mu}m$ in vibration amplitude (sometimes it increased to $221{\mu}m$ maximum. alarm: 6 mils, trip: 9 mils) at base load. After applying the study, they decreased to about $45{\mu}m$ maximum. It is a result from that we did not change the setting value of bearing alignment and only changed the assembly position of internal parts in Synchro clutch coupling rachet wheel which links between high pressure turbine and low pressure turbine, and increased the internal gap and machining of the Pawl cage surface. In the operation of steam turbine, if the vibration value increases by 1X, we should reduce the vibration of bearing by weight balancing. However, unless the vibration of bearing is declined by the balancing, we will have to disassemble and check the component and find the cause. In this study, we researched the way to lower mass unbalance that is 1X vibration component which has the greatest portion of vibration generated by steam turbine and we got good result by applying the findings of this study.