• 전력전자학회:학술대회논문집
• /
• 전력전자학회 1998년도 전력전자학술대회 논문집
• /
• pp.291-294
• /
• 1998

This paper presents a new active power filter with low DC voltage for compensating reactive power and harmonics of three-phase high power/voltage harmonic producing load. It has a structure of converter connected in series with power factor correction capacitor. Appropriate size and number of filter capacitor are determined by an equation and applied to simulation of 10kvar 6-pulse SCR rectifier.

• 한국구조물진단유지관리공학회 논문집
• /
• 제14권3호
• /
• pp.186-195
• /
• 2010

본 논문은 SC합성보에 정착구의 높이, 새들의 형태, 가력시점을 변수로 하여 비부착 포스트텐션 보강을 하고 휨실험을 통해 보강방법을 평가하여 적절한 보강방법을 제시하고자 하엿다. 실험결과 보강 전 SC합성보의 최대내력은 실험값/이론값이 0.97로 나타났으나 보강 후는 1.00~1.21로 나타나 보강효과를 확인할 수 있었다. 변위 및 변형률 분석결과 정착구의 높이 및 가력시점에 상관없이 보강 후 중립축에 정착구를 설치한 D120계열 실험체가 최대하중이후 급격한 하중저하 없이 변위가 지속적으로 증가하며 각 부분의 변형률도 비교적 적게 나타나는 안정적인 거동을 했다. 보강효과면에서 선 가력 후 보강한 SCR-UD120실험체가 보강 전 SC합성보에 비해 최대내력이 1.72배 증가하여 가장 우수한 것으로 나타났다.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 2005년도 전력전자학술대회 논문집
• /
• pp.366-369
• /
• 2005

The smelting system using induction heating technology has many advantages over conventional fossil fuel regarding energy efficiency, environmental aspect and so on. This paper introduces the principal and technical trends of Induction heating technology, and describes recently developed 2500kW induction smelting inverter, The developed inverter is a series resonant type using high speed Thyristor (SCR) and employs state-of-art digital controller using DSP.

• 한국초전도ㆍ저온공학회논문지
• /
• 제18권2호
• /
• pp.18-20
• /
• 2016

The study of superconducting fault current limiter (SFCL) is continuously being studied as a countermeasure for reducing fault-current in the power system. When the fault occurred in the power system, the fault-current was limited by the generated impedance of SFCLs. The operational characteristics of the flux-offset type SFCL according to turn ratios between the primary and the secondary winding of a reactor were compared in this study. We connected the secondary core to a superconductor and a SCR switch in series in the suggested structure. The fault current in the primary and the secondary winding of the reactor and the voltage of the superconductor on the secondary were measured and compared. The results showed that the fault current in the load line was the lowest and the voltage applied at both ends of the superconductor was also low when the secondary winding of the reactor had lower turn ratio than the primary. It was confirmed based on these results that the turn ratio of the secondary winding of the reactor must be designed to be lower than that of the primary winding to reduce the burden of the superconductor and to lower the fault current. Also, the suggested structure could increase the duration of the limited current by limiting the continuous current after the first half cycle from the fault with the fault current limiter.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2009년도 추계학술대회 논문집
• /
• pp.382-386
• /
• 2009

This paper describes design and analysis techniques of cold forging process for precise producing of T-200 type spider made of SCr420H by utilizing pneumatically operated enclosed die set. Since deducing feasible closing force is an important factor to optimize entire pneumatically operated cold forging system, a series of FE analyses with varying the number of gas cylinders has been carried out to investigate the influence of closing force upon the direction of applied load at die surfaces. It also reveals the optimum distribution of the gas cylinders in terms of the flatness of upper/lower plates.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1990년도 하계학술대회 논문집
• /
• pp.261-264
• /
• 1990

The specific contact resistance(SCR) of metal-semiconductor interface is an important design parameter for VLSI interconnecting technology. As the critical feature size of the integrated structures decrease, the physical size of ohmic contacts will also decrease and the series contact resistance will increase. Al-Si contacts on the annealing condition are studied. The propreties of the contacts depend considerably on the annealing procedures. Barrier height is measured from Capacitance-Voltage characteristics. The specific contact resistance are analyzed using a modified four point method.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1999년도 하계학술대회 논문집 E
• /
• pp.2189-2191
• /
• 1999

To improve the reliability of the klystron-modulator systems, the stable operations of the thyratron an important factor of the system are required. The thyratron always has a possibility of self-fire according to the conditions of the applied high voltage and this induces the system fault. Therefore a command charging method was introduced to reduce the applied tim8 of the high voltage into the thyratron. The high voltage switch used in the command charging method is the SCR (1.6 kV, 50A) and consists of 10 SCRs in series to discharge 10 kV. A pulse transformer was used to apply the trigger pulse. The objectives of this research are the fabrication of the semiconductor switch and the study of the experimental result of the operation characteristics of the high voltage semiconductor switch.

• 소성∙가공
• /
• 제23권4호
• /
• pp.221-230
• /
• 2014

This study deals with a series of experimental investigations on multi-stage cold forging of an outer race used for a constant velocity (CV) joint with six inner ball grooves. The multi-stage cold forging, which consists of forward extrusion, upsetting, backward extrusion, and combined sizing-necking including ironing, was used to produce a prototype of the outer race. The cold forging tools such as forging punches and dies required in this multi-stage cold forging were also designed and fabricated. For the combined sizing-necking, especially, the longitudinally six-segmentallized punches were developed to easily eject from the necked inner groove of the outer race with consideration of the operating mechanism. Spheroidized SCr420H billet was used in the experimental study. To verify the suitability of the proposed process, the obtained parts were obtained from each forging operation, and the geometries were compared with the target dimensions. It was confirmed that the outer race with six inner ball grooves was well forged by adopting the proposed multi-stage cold forging, and the dimensional accuracy of the forged outer race matched well with the requirements.

• 한국대기환경학회지
• /
• 제6권1호
• /
• pp.31-42
• /
• 1990

In order to suggest an efficient catalyst systems for NOx reduction of flue gases from industrial boilers, $TiO_2$ supported $WO_3-V_2O_5, V_2O_5$ and $WS_2$ catalysts were tested for the performances of NOx reduction at high reactin temperature range (250-500$^\circ$C) using a simulated flue gas system. It was found that while the proposed $WO_3/TiO_2$ and $WO_3-V_2O_5/TiO_2$ catalysts showed a significant high NOx reduction efficiency at about 350-400$^\circ$C, the conventional commercial catalyst of $V_2O_5/TiO_2$ showed a significant drop in NOx reduction efficiency due to the excessive $NH_3$ oxidation. From the measurement of surface acidities of those catalysts, it was found that the acidity are well correlated with the activities of NOx reduction. The reason of high activity of $WO_3$ series catalysts at high reaction temperature seems due to the low value of surface excess oxygen compared with that of $V_2O_5/TiO_2$ seems equivalent to the acid site of that catalyst.

• 품질경영학회지
• /
• 제20권2호
• /
• pp.109-117
• /
• 1992

An inspection task largely can be seen as a job divided up into a series of visual search and classification subtasks. In these subtasks, an Inspector must performs to compare the standard references proposed in visual environments and recalled in his memory with the visual stimuli to be inspected. It means that the judgement of similarity should be demanded on inspection tasks. Therefore, the inspector's ability for the judgement of similarity and the difference similarity between inspection materials are important factors to effect on performances in inspection tasks. In this paper, to analysis the effect of these factors on inspection time, an inspection task is designed and suggested by means of computer simulator. Especially, the skin conductance responses(SCR) of subjects are measured to evaluate the complexity of tasks due to the difference of similarity between materials. In the results of experiment, the more similar or different the difference of similarity between materials is, the shorter the inspection time is because of the reduction of task complexity. And, When the inspector's cognition for similarity between materials is consistanct, the inpsection time is improved. Concludingly, the consistency of reponses for similarity judgement becomes a measurement to present the performance levels. And the information of inspection time that due to the difference of similarity between materials must be considered in planning and scheduling inspection tasks.