• International Journal of Aeronautical and Space Sciences
• /
• v.17 no.1
• /
• pp.29-36
• /
• 2016

Tensairity girder is a light weight inflatable fabric structural concept which can be used in road emergency transportation. It uses low pressure air to stabilize compression elements against buckling. With the purpose of obtaining the comprehensive target of minimum deflection and weight under ultimate load, the cross-section and the inner pressure of tensairity girder was optimized in this paper. The Variable Complexity Modeling (VCM) method was used in this paper combining the Kriging approximate method with the Finite Element Analysis (FEA) method, which was implemented by ABAQUS. In the Kriging method, the sample points of the surrogate model were outlined by Design of Experiment (DOE) technique based on Optimal Latin Hypercube. The optimization framework was constructed in iSIGHT with a global optimization method, Multi-Island Genetic Algorithm (MIGA), followed by a local optimization method, Sequential Quadratic Program (SQP). The result of the optimization gives a prominent conceptual design of the tensairity girder, which approves the solution architecture of VCM is feasible and efficient. Furthermore, a useful trend of sensitivity between optimization variables and responses was performed to guide future design. It was proved that the inner pressure is the key parameter to balance the maximum Von Mises stress and deflection on tensairity girder, and the parameters of cross section impact the mass of tensairity girder obviously.

• Journal of Mechanical Science and Technology
• /
• v.15 no.7
• /
• pp.876-888
• /
• 2001

For a large scaled optimization based on response surface methods, an efficient quadratic approximation method is presented in the context of the trust region model management strategy. If the number of design variables is η, the proposed method requires only 2η+1 design points for one approximation, which are a center point and tow additional axial points within a systematically adjusted trust region. These design points are used to uniquely determine the main effect terms such as the linear and quadratic regression coefficients. A quasi-Newton formula then uses these linear and quadratic coefficients to progressively update the two-factor interaction effect terms as the sequential approximate optimization progresses. In order to show the numerical performance of the proposed method, a typical unconstrained optimization problem and two dynamic response optimization problems with multiple objective are solved. Finally, their optimization results compared with those of the central composite designs (CCD) or the over-determined D-optimality criterion show that the proposed method gives more efficient results than others.

• Journal of Mechanical Science and Technology
• /
• v.20 no.3
• /
• pp.366-375
• /
• 2006

In this paper, it is intended to introduce a method to solve multi-objective optimization problems and to evaluate its performance. In order to verify the performance of this method it is applied for a vertical roller mill for Portland cement. A design process is defined with the compromise decision support problem concept and a design process consists of two steps: the design of experiments and mathematical programming. In this process, a designer decides an object that the objective function is going to pursuit and a non-linear optimization is performed composing objective constraints with practical constraints. In this method, response surfaces are used to model objectives (stress, deflection and weight) and the optimization is performed for each of the objectives while handling the remaining ones as constraints. The response surfaces are constructed using orthogonal polynomials, and orthogonal array as design of experiment, with analysis of variance for variable selection. In addition, it establishes the relative influence of the design variables in the objectives variability. The constrained optimization problems are solved using sequential quadratic programming. From the results, it is found that the method in this paper is a very effective and powerful for the multi-objective optimization of various practical design problems. It provides, moreover, a reference of design to judge the amount of excess or shortage from the final object.

• KSII Transactions on Internet and Information Systems (TIIS)
• /
• v.12 no.12
• /
• pp.5614-5633
• /
• 2018

Mobile Edge Computing (MEC) and Wireless Power Transfer (WPT) are both recognized as promising techniques, one is for solving the resource insufficient of mobile devices and the other is for powering the mobile device. Naturally, by integrating the two techniques, task will be capable of being executed by the harvested energy which makes it possible that less intrinsic energy consumption for task execution. However, this innovative integration is facing several challenges inevitably. In this paper, we aim at prolonging the battery life of mobile device for which we need to maximize the harvested energy and minimize the consumed energy simultaneously, which is formulated as residual energy maximization (REM) problem where the offloading ratio, energy harvesting time, CPU frequency and transmission power of mobile device are all considered as key factors. To this end, we jointly optimize the offloading ratio, energy harvesting time, CPU frequency and transmission power of mobile device to solve the REM problem. Furthermore, we propose an efficient convex optimization and sequential unconstrained minimization technique based combining method to solve the formulated multi-constrained nonlinear optimization problem. The result shows that our joint optimization outperforms the single optimization on REM problem. Besides, the proposed algorithm is more efficiency.

• Smart Structures and Systems
• /
• v.33 no.3
• /
• pp.177-188
• /
• 2024

The fatigue-induced sequential failure of a structure having structural redundancy requires system-level analysis to account for stress redistribution. System reliability-based design optimization (SRBDO) for preventing fatigue-initiated structural failure is numerically costly owing to the inclusion of probabilistic constraints. This study incorporates the Branch-and-Bound method employing system reliability Bounds (termed the B³ method), a failure-path structural system reliability analysis approach, with a metaheuristic optimization algorithm, namely grey wolf optimization (GWO), to obtain the optimal design of structures under fatigue-induced system failure. To further improve the efficiency of this new optimization framework, an additional bounding rule is proposed in the context of SRBDO against fatigue using the B³ method. To demonstrate the proposed method, it is applied to complex problems, a multilayer Daniels system and a three-dimensional tripod jacket structure. The system failure probability of the optimal design is confirmed to be below the target threshold and verified using Monte Carlo simulation. At earlier stages of the optimization, a smaller number of limit-state function evaluation is required, which increases the efficiency. In addition, the proposed method can allocate limited materials throughout the structure optimally so that the optimally-designed structure has a relatively large number of failure paths with similar failure probability.

• Proceedings of the Korea Committee for Ocean Resources and Engineering Conference
• /
• 2004.05a
• /
• pp.67-72
• /
• 2004

Many port states such as New Zealand, the USA, Australia and Canada have strict regulations to prevent ships which arrive in their port from discharging polluted ballast water which contain harmful aquatic organism and pathogens. They are notified that transfer of polluted ballast water can cause serious injury to public health and damage to property and environment. For this reason, they perceived that the ballast exchange in deep sea is the most effective method, together with submitting the ballast management plan which contains the effective exchange method, ballast system and safety consideration. In this study, we pursued both nautical engineering analysis and optimization of algorithm in order to generate the sequence of stability and rapidity. Heuristic Algorithm was chosen on the basis of optimality and applicability to a sequential exchange problem. We have built an optimized algorithm, for automatic exchange of ballast water, by redefining core elements of the $A^\ast$ algorithm, such as node, operator and evaluation function. Final version of the optimized algorithm has been applied to existing bulk carrier and the performance of the algorithm has been verified successfully.

• Advances in robotics research
• /
• v.2 no.2
• /
• pp.161-182
• /
• 2018

This paper proposes a novel receding horizon control (RHC) algorithm for formation control of a swarm of unmanned surface vehicles (USVs) using particle swarm optimization (PSO). The proposed control algorithm provides the coordinated path tracking of multi-agent USVs while preventing collisions and considering external disturbances such as ocean currents. A three degrees-of-freedom kinematic model of the USV is used for the RHC with guaranteed stability and convergence by incorporating a sequential Monte Carlo (SMC)-based particle initialization. An ocean current model-based estimator is designed to compensate for the effect of ocean currents on the USVs. This method is compared with the PSO-based RHC algorithms to demonstrate the performance of the formation control and the collision avoidance in the presence of ocean currents through numerical simulations.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.15 no.8 s.101
• /
• pp.911-917
• /
• 2005

There were many attempts to reduce noise behind the noise barrier using active control techniques. Omoto(1993) Shao(1997) and Yang(2001) tried to actively control the diffracted noise behind the barrier and main concerns were about the arrangement methods for the control sources. Baek (2004) tried to get better results using the simulated annealing method and the sequential searching technique. The main goal of this study is to develop and compare the performance of several optimization techniques including those mentioned above, hybrid version of simulated annealing and genetic algorithm for the optimal control source positions of active noise barrier system. The simulation results show fairly similar performance lot the small size of searching problem. However, as the number of control sources are increased, the performance of simulated annealing algorithm and genetic algorithm are better than the others. Simulations are also made to show the performance of the selected optimal control source positions not only at the receiver position but at the surrounding volume of the receiver position and plotted the noise reduction level in 3-D.

• Journal of IKEEE
• /
• v.23 no.4
• /
• pp.1400-1407
• /
• 2019

In this paper, we propose a support vector machine (SVM) based gas classifier that can support real-time self-learning. The modified sequential minimal optimization (MSMO) algorithm is employed to train the proposed SVM. By using a shared structure for learning and classification, the proposed SVM reduced the hardware area by 35% compared to the existing architecture. Our system was implemented with 3,337 CLB (configurable logic block) LUTs (look-up table) with Xilinx Zynq UltraScale+ FPGA (field programmable gate array) and verified that it can operate at the clock frequency of 108MHz.

• Journal of Wetlands Research
• /
• v.11 no.2
• /
• pp.107-121
• /
• 2009

Many rainfall-runoff models have been used for the flood forecasting. However, the determination of rainfall-runoff model parameters is very difficult. In this study, we investigated the efficiency of flood forecasting models by studying the optimization techniques for parameter calibration of SFM, Tank, and SSARR models. We analyzed the correlations between parameters in optimization techniques, then classified the parameters into parameter groups. For this we applied the sequential calibration method through the sensitivity analysis. As the results of the analysis, the parameter groups clibration method showed better result for peak flow and clibtation time.