• 한국유체기계학회 논문집
• /
• 제14권6호
• /
• pp.91-95
• /
• 2011

This paper deals with the detail rotordynamic analysis for the assembly rotor composed of turbine wheel, turbine shaft, connecting arbor, and flange & spindle in order to perform the spin test of turbocharger turbine. Prior to rotordynamic analysis, the 1st spin test was performed but the test was failed by excess vibration in the neighborhood rated speed. It is the reason for this fail that the separation margin between the rated speed and critical speed is not enough, confirmed by rotordynamic analysis results. Since then, the dimension of turbine shaft was modified and the critical speeds were again reviewed for modified assmebly rotor. In results, the separation margin between the rated speed and critical speed is over 20% and then the 2nd spin test was performed successfully. In preparing spin test for turbine, compressor wheels and etc., the geometry design of connecting arbor and dimension of rough machining should be reviewed by considering rotordynamic results, and the separation margin should be enough for successful spin test.

• 한국소음진동공학회논문집
• /
• 제23권3호
• /
• pp.267-273
• /
• 2013

Recently, turbine-generators have been replaced for the integrity reinforcement and the efficiency improvement, also, the blade's failures of LP turbines due to torsional vibration have been reported. Excessive torsional vibrations can result in failures of components. The severity of torsional oscillations and stress depends upon the separation margin between the excitation frequencies and torsional natural frequencies. Therefore it is needed to measure the torsional natural frequencies after replacement of the components to conform the separation margin of torsional natural frequencies. In this study torsional vibration measurements were performed after LP turbine and generator replacement and the torsional natural frequencies for the turbine-generator train were calculated to evaluate the effects of generator replacement on torsional natural frequencies of turbine-generator train. It is expected that these evaluation results will be used effectively to identify the root causes of torsional vibration problems.

• 한국정밀공학회지
• /
• 제15권6호
• /
• pp.145-152
• /
• 1998

This paper presents an optimum design of a rotor-bearing spindle system for a ultra centrifuge (80,000 RPM) supported by ball bearings with nonlinear stiffness characteristics. To obtain the nonlinear bearing stiffnesses, a ball bearing is modeled in five degrees of freedom and is analyzed quasi-statically. The dynamic behaviors of the nonlinear rotor-bearing system are analyzed by using a transfer-matrix method iteratively. For optimization. we use the cost function that simultaneously minimizes the weight of a rotor and maximizes the separation margins to yield the critical speeds as far from the operating speed as possible. Augmented Lagrange Multiplier (ALM) method is employed for the nonlinear optimization problem. The result shows that the rotor-bearing spindle system is optimized to obtain 9.5％ weight reduction and 21％ separation margin.

• 한국지구물리탐사학회:학술대회논문집
• /
• 한국지구물리탐사학회 2007년도 특별 심포지엄 논문집
• /
• pp.73-83
• /
• 2007

We interpreted marine seismic profiles in conjunction with swath bathymetric and magnetic data to investigate rifting to breakup processes at the eastern Korean margin that led to the separation of the southwestern Japan Arc. Analysis of rift fault patterns suggests that rifting at the Korean margin was primarily controlled by normal faulting resulting from extension rather than strike-slip deformation. Two extension directions of E-W and NW-SE for rifting are recognized. We interpret that the E-W direction represents initial rifting at the inner margin and the NW-SE direction probably represents the extension in response to tensional tectonics associated with the subduction of the Pacific Plate in the NW direction. No significant volcanism was involved in rifting. In contrast, the inception of sea floor spreading documents a pronounced volcanic phase which appears to reflect asthenospheric upwelling as well as rift-induced convection particularly in the narrow southern margin. We suggest that structural and igneous evolution of the Korean margin, although it is in a back-arc setting, can be explained by the processes occurring at the passive continental margin with magmatism influenced by asthenospheric upwelling.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2010년도 춘계학술대회 논문집
• /
• pp.225-226
• /
• 2010

ISO 22266-1 issued in May 2009 provides guidelines for applying shaft torsional vibration criteria, under normal operating conditions, for the coupled shaft system and long blades of a turbine generator set. In case that a turbine generator vendor do not meet the separation margin of torsional natural frequencies in the technical specifications of the purchaser, this standard can present the reasonable and objective criteria about torsional vibration which both purchaser and supplier can agree on, while ensuring the integrity of turbine generator. This paper describes the application case of ISO 22266-1 for the establishment of torsinal vibration criteria under retrofitting the turbine generator of 'U' nuclear power plant.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2008년 영문 학술대회
• /
• pp.66-71
• /
• 2008

Two cases with circumferential grooves were designed for a transonic compressor, and 3-D numerical simulations were conducted for stall mechanism at three representative speeds. A conclusion can be drawn from the comparison between compressors with or without casing treatment that: with the rising of rotation speed, stall margin increases dramatically under the help of casing treatments, and the case with middle grooves has reasonable compromise between stall margin increment and efficiency cutting. At lower speed, the increment reduces, and grooves at the back of blade tip have more influence on stall margin. Further investigation shows there is a transition in mechanism of compressor stall with the decline of rotational speed: at high rotation speed, the expansion of stall margin mainly results from the suppression of tip leakage vortex by casing treatments, yet it benefits more from the depression of boundary layer separation from suction surface of blade tip.

• 보건의료산업학회지
• /
• 제5권1호
• /
• pp.77-85
• /
• 2011

The study intends to conduct an analysis of relations between efficiency of investment to human resources and the operating margin in hospitals. The analyzed results are as follows: First, it is found out that an index related to labor productivity(the monthly value added per bed, the value added ratio to gross revenue), and an index for efficiency of human resources(value added to personnel expenses), do not have a significant difference by years. Second, labor productivity, indicating the efficiency of human resources, does not have a significant difference between regions and between hospital types. But there is a significant difference according to types of establishment: private hospitals have higher labor productivity(efficiency of human resources) than corporate hospitals. The hospital size is small have significantly higher labor productivity. As a result of a follow-up check, it is found out that there is separation between a group with more than 200 beds and a group with less than 200 beds. Third, at the relations between the indices related to value-added productivity and the operating margin that the higher the value added ratio to gross revenue and the higher labor productivity, the higher the operating margin. Especially, labor productivity(value added to personnel expenses), an index for the efficiency of human resources, out of all the indices related value added productivity, has the most significant influence on the operating margin.

• 응용통계연구
• /
• 제18권2호
• /
• pp.421-434
• /
• 2005

기계학습은 패턴분류의 한 도구로써 광범위하게 연구되고 있다. 기계학습 방법들 중에서 서포트 벡터 기계(Support Vector Machines)는 많은 분야에서 연구되어지는 것으로 이진 패턴 분류문제에서 고차원의 특징공간에서 두 집합들 사이에 가장 큰 분리를 제공하는 최대 여유도(margin)를 가지는 분리 초평면을 찾는 것이다. 최대 여유도의 분리의 개념에 기초하여 Mangasarian(1968)은 다중-표면 방법(multi-surface method)을 제안하였고, 1980년대에 목적 계획법을 이용한 방법들이 광범위하게 개발되었다. 본 논문에서는 다목적 계획법과 목적 계획법을 이용한 수리계획법인 서포트 벡터 기계의 두가지 방법들을 제안하고 수치 예제들을 통하여 효용성에 대하여 논의하고자 한다.

• 한국병원경영학회지
• /
• 제8권3호
• /
• pp.118-142
• /
• 2003

This study is aimed at evaluating the financial structure of hospitals before and after the separation of prescription and drug dispensing policy started to be implemented in July 2000 and at making a suitable hospital managerial strategy through the verification of the factors which have effect on their profitability. This study investigated the hospitals which have passed the accredition review to be designated as a accredited training hospital each year for three years from 1999 to 2001. Those hospitals were selected from members of the Korea Hospital Association. 106 hospitals were targeted for analysis except for the hospitals whose financial statements and managerial performance were not reported faithfully. The financial indicators used in this study were stability indicators(liability to total assets, ratio of debt to fund balance, fixed ratio), liquidity indicators(current ratio, quick ratio), activity indicators(total assets turnover, fixed assets turnover), profitability indicators(net profit to total assets, net profit to net worth, operating margin), and operating expenses to patient revenues indicators(drug and supplies costs/payroll/overhead expenses). The result of this study are as follows: First, the analysis of the increase of loss-making hospitals before and after. The separation of prescription and drug dispensing policy shows that the number of loss-making hospitals increase after the separation(22.6% before the separation; 31.1% after the separation). However, there was no significant statistical difference. Second, the analysis of operating expenses to patient revenues indicators showed that the ratio of drug and supplies cost became lower in all hospitals but the ratio of payroll/overhead expenses became higher. Additionally, the factor which have the greatest effect on profitability was operating expenses to patient revenues indicators (drug and supplies costs/payroll/overhead expenses). Third, the analysis of managerial performance by four types of loss-loss, loss-profit, profit-loss and profit-profit compared the results before the separation with those after the separation revealed as follows : Reliance on liability to total assets became higher in the profit-loss type($56.2%{\rightarrow}66.4%$), lower in the loss-profit type($82.7%{\rightarrow}74.5%$). Total assets turnover became higher in the profit-profit type($1.3{\rightarrow}1.5$), but lower in the loss-profit type($0.8{\rightarrow}0.7$). Operating margin decreased to minus 5.9% from 4.3% in the profit-loss type, but increased to 7.2% from minus 7.8% in the loss-profit type. Forth, operating expenses to revenues indicators showed that the increase of payroll was the biggest in the profit-loss type($39.2%{\rightarrow}49.9%$) and that overhead cost decreased in the loss-profit type but that rather increased in other types.

• 자원환경지질
• /
• 제27권6호
• /
• pp.571-577
• /
• 1994

미국 대서양 대륙주변부는 북미와 아프리카 대륙의 중생대 분열의 산물로서 화산성 기원 혹은 비화산성 기원인가에 대해 논란이 있어 왔다. 이를 규명하기 위하여 미국 남동부 해안에서 채취한 다채널 탄성파 단면도에 나타난 기반암들의 영상을 조사하였다. 가장 핵심적인 탄성파 영상의 하나는 전체적으로 쐐기 형상을 보이는 해양방향의 경사반사층들(seaward-dipping reflectors; SDR)이다. 이들은 화산성 열개주변부의 상징적인 기반암 구조로 알려져 있다. 연구지역에는 2 개조의 해양경사층 쐐기구조가 존재하였다: 하나는 기반암 경첩대 (basement hinge zone) 부근이고 ('the hinge SDR wedge'라고 명명), 다른 하나는 미국 동해안 자기이상대 (the East Coast magnetic anomaly)의 바다 쪽에 위치한다 ('the outer SDR wedge'라고 명명). 또한, 기반암 경첩대의 동쪽 지각에서는 "7.2 km/s 층"으로 알려진 높은 속도의 하부지각층과 함께 원만한 기복의 모호 불연속면 등이 관찰되었다. 이러한 기반암 구조와 잘 알려진 화산성 기원의 대륙주변부의 지각구조를 비교해 보아 미국 남동부 대륙주변부를 화산성 기원의 대륙주변부로 특징지었다.