• Journal of Sensor Science and Technology
• /
• v.16 no.3
• /
• pp.192-196
• /
• 2007

A fiber-optic interferometric temperature sensor is fabricated using a hollow optical fiber with 8 um air hole. This interferometric sensor for measuring temperature consists of 13 mm long hollow optical fiber whose one end is attached to the single mode fiber and the other end is cleaved. After the sensor is put in a furnace, the phase change of the sensor output signal is measured as the temperature of the furnace increases from $28^{\circ}C$ to $100^{\circ}C$. The phase change of the fiber sensor is proportional to the change of temperature and the relationship between the change of phase and temperature is approximately linear. The sensitivity of this sensor is $2.7{\;}radians/^{\circ}C$.

• Smart Structures and Systems
• /
• v.6 no.5_6
• /
• pp.525-543
• /
• 2010

Testing and validation processes are critical tasks in developing a new hardware platform based on a new technology. This paper describes a series of experiments to evaluate the performance of a newly developed MEMS-based wireless sensor node as part of a wireless sensor network (WSN). The sensor node consists of a sensor board with four accelerometers, a thermometer and filtering and digitization units, and a MICAz mote for control, local computation and communication. The experiments include calibration and linearity tests for all sensor channels on the sensor boards, dynamic range tests to evaluate their performance when subjected to varying excitation, noise characteristic tests to quantify the noise floor of the sensor board, and temperature tests to study the behavior of the sensors under changing temperature profiles. The paper also describes a large-scale deployment of the WSN on a long-span suspension bridge, which lasted over three months and continuously collected ambient vibration and temperature data on the bridge. Statistical modal properties of a bridge tower are presented and compared with similar estimates from a previous deployment of sensors on the bridge and finite element models.

• Journal of Sensor Science and Technology
• /
• v.30 no.1
• /
• pp.42-46
• /
• 2021

In this paper, we describe the development of a force sensor to measure the tool gripping force of the BT50 spindle. The force sensor for a BT50 must be installed inside the gripping force tester; hence, it must be of an appropriate size and have a rated capacity suitable for measuring the gripping force. So, the structure of the force sensor for BT50 was modeled, the size of the sensing part was determined by structural analysis, and the force sensor was manufactured by attaching a strain gauge. The characteristic test results of the manufactured force sensor, indicated that the nonlinearity error, hysteresis error, and reproducibility errors were each within 0.91%, Therefore it was determined that the manufactured force sensor can be used for checking the spindle tool gripping force.

• Journal of Sensor Science and Technology
• /
• v.27 no.3
• /
• pp.199-203
• /
• 2018

In this study, we develop a methane sensor module that can detect low concentrations below 5,000 ppm and measure up to the detection limit of 50 ppm with the NDIR method, with a long lifetime and high accuracy. Methane ($CH_4$) is one of a representative greenhouse gas, which is very explosive. Thus, it is important to quickly and accurately measure methane concentration in the air. To adjust the methane sensor for industrial field applications, a NDIR-based small sensor was implemented and characterized, where its volume was $4cm{\times}4cm{\times}2cm$ and its response time ($T_{90}$) was less than 30 sec. These results demonstrate that the proposed sensor is commercially available for low-concentration measurement, low volume, and fast response application, such as IoT sensor nodes and portable devices.

• Journal of Sensor Science and Technology
• /
• v.25 no.1
• /
• pp.35-40
• /
• 2016

Pulse diagnosis is one of the representative diagnostic methods in Oriental medicine. In this study, a pulse pressure sensor array coated with silicone, which includes 6 piezo-resistive sensors and 1 thermistor, is fabricated for pulse measurement. It is necessary to coat the pulse sensor array with silicone to avoid the fracture or damage of pressure sensors when the sensor is in contact with the skin and a constant pressure is applied. However, the silicone coating on the pulse sensor array can cause signal interference among the sensors in the pulse sensor array. The interference number (IN), a calculation for expressing the degree of interference among channels, is changed according to the silicone thickness on the pulse sensor array. The IN is increased by a thick silicone coating, but the fabrication error, an important index for the mass production of the sensor array, is reduced by the thickness of the silicone coating. We propose that the thickness of the silicone on the pulse sensor array is an important consideration for the performance of the fabricated sensor and manufacturing repeatability.

• Journal of Sensor Science and Technology
• /
• v.24 no.2
• /
• pp.137-143
• /
• 2015

This paper describes the design of a two-axis force sensor with two step plate beams for measuring forces in an upper-limb rehabilitation robot. The two-axis force sensor is composed of a Fz force sensor and a Ty torque sensor. The Fz force sensor measures the force applied to a patient's arm pushed by a rehabilitation robot and the force of patient's arm. The Ty torque sensor measures the torque generated by a patient's arm motion in an emergency. The structure of sensor is composed of a force transmitting block, two step plate beams and two fixture blocks. The two-axis force sensor was designed using FEM (Finite Element Method), and manufactured using strain-gages. The characteristics test of the two-axis force sensor was carried out. as a test results, the interference error of the two-axis force sensor was less than 1.24%, the repeatability error of each sensor was less than 0.03%, and the non-linearity was less than 0.02%.

• Proceedings of the KIEE Conference
• /
• 2001.07c
• /
• pp.1896-1898
• /
• 2001

An offset problem caused by the static parasitic capacitors is analyzed and then some techniques to reduce their effect on the capacitive position sensor are presented. Also new offset compensation technique is proposed that by adjusting the magnitudes of the modulating signals independently, the charge imbalance between electrodes caused by the parasitic capacitors is eliminated without sensor gain variation. Simulation results are given to validate the proposed compensation technique.

• Journal of Industrial Technology
• /
• v.33 no.A
• /
• pp.67-72
• /
• 2013

CNT(carbon nanotube) humidity sensors with plasma treated electrodes exhibit a much faster response time and a higher sensitivity to humidity, compared to untreated CNT and porous Cr electrodes. These results may be partially due to their percolated pore structure being more accessible for water molecules and for expending the diffusion of moisture to the polyimide sensing film, and partially due to the oxygenated surface of CNT films. This paper shows a plasma process effect and selectivity characteristics of CNT film humidity sensor.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.5 no.1
• /
• pp.87-92
• /
• 2004

This review focuses on the developed and the being developed environmental sensors in particular biological sensors. As well as discussing the classification and some main principles, presenting current trend of the environmental sensors is given. Two main categories are immunosensors and catalytic sensors. In addition to those. DNA or RNA sensors or protein based sensors are discussed. Some crucial examples of the applications of such sensors are given to show how the sensor technology it used for environmental and biological monitoring, biomarkers of exposure.

• Journal of Sensor Science and Technology
• /
• v.6 no.6
• /
• pp.508-513
• /
• 1997

We exploited a new molecular system - acetylcholine (neurotransmitter) detection system as a building block for the perfect molecular information system (sensing membrane of the chemical sensor) - using water soluble calix[n]arene-p-sulfonates which are useful even in aqueous (water/methanol) neutral solution. This achievement is due to several outstanding properties of these calix[n]arene derivatives such as low $pK_{a}$ values, cation-interactions, and high water-solubility, etc.