• Journal of Sensor Science and Technology
• /
• v.29 no.6
• /
• pp.427-432
• /
• 2020

The most lethal foreign body in meat is a needle, and X-ray images are used to detect it. However, because the difference in thickness and fat content is severe depending on the type of meat and the part of the meat, the shade difference and contrast appear severe. This problem causes difficulty in automatic classification. In this paper, we propose a method for generating training patterns by efficient pre-processing and classifying needles in meat using a convolution neural network. Approximately 24000 training patterns and 4000 test patterns were used to verify the proposed method, and an accuracy of 99.8% was achieved.

• Journal of Sensor Science and Technology
• /
• v.15 no.2
• /
• pp.112-119
• /
• 2006

Resolution of an image sensor is very significant parameter to improve. It is hard to improve the resolution of the CMOS vision chip for edge detection based on a biological retina using a resistive network because the vision chip contains additional circuits such as a resistive network and some processing circuits comparing with general image sensors such as CMOS image sensor (CIS). In this paper, we proved the problem of low resolution by separating photo-sensing and signal processing circuits. This type of vision chips occurs a problem of low operation speed because the signal processing circuits should be commonly used in a row of the photo-sensors. The low speed problem of operation was proved by using a reset decoder. A vision chip for edge detection with $128{\times}128$ pixel array has been designed and fabricated by using $0.35{\mu}m$ 2-poly 4-metal CMOS technology. The fabricated chip was integrated with optical lens as a camera system and investigated with real image. By using this chip, we could achieved sufficient edge images for real application.

• International conference on construction engineering and project management
• /
• 2009.05a
• /
• pp.1278-1282
• /
• 2009

In apartment type of housing, if resident's vehicle is registered in central control office and RFID TAG is issued, identification can be recognized from the time of entrance into parking lot and intelligent parking guide system can be activated based on the residents' profile. Parking Guide System leads a vehicle to the available parking space which is closest to the entrance gate of the vehicle's owner. And when residents forget where they parked their cars, they can query to the Parking Guide and Management System and get responses about the location. For the correct operation of this system, it is necessary to find out where the residents' cars have parked in real time and which lot is available for parking of other cars. RFID is very fancy solution for this system. RFID reader gathers the ID information in RFID TAGs in parked cars and updates the DB up to date. But, when non-residents' cars are parked inside apartment, RFID reader cannot identify them nor know the exact empty/occupied status of parking spaces because they don't react to RFID reader's query. So for the exact detection of empty/occupied status, we suggest the combined use of ultrasonic sensors and RFID. We designed a tree topology with intermediate data aggregators. The depth of tree is normally more than 3 from root (central office) to leaves (individual parking lots). The depth of 2 in tree topology brings about the bottleneck in communication and maintenance. We also designed the information fields used in RFID networks and Sensor Networks.

• Journal of Sensor Science and Technology
• /
• v.10 no.6
• /
• pp.286-294
• /
• 2001

In this study, 3-D underwater object recognition using the self-made 3-3 type composite ultrasonic transducer and modified SOFM(Self Organizing Feature Map) neural network are investigated. Properties of the self-made 3-3 type composite specimens are satisfied considerably with requirements as an underwater ultrasonic transducer's materials. 3-D underwater all object's recognition rates obtained from both the training data and testing data in different objects, such as a rectangular block, regular triangular block, square block and cylinderical block, were 100% and 94.0%, respectively. All object's recognition rates are obtained by utilizing the self-made 3-3 type composite transducer and SOFM neural network. From the object recognition rates, it could be seen that an ultrasonic transducer fabricated with the self-made 3-3 type composite resonator will be able to have application for the underwater object recognition.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.19 no.3
• /
• pp.209-215
• /
• 2006

This paper was proposed Intelligent and wireless USN/RFID module system that can overcome disadvantage of existing RFID system with no sensing module and wire communication. The proposed USN/RFID system was designed and fabricated. After fabricating new system, we analyzed the characteristics of USN/RFID module. After design VCO block that is point circuit to develop next generation system one chip of RFID system, we were carried out simulation and verified the validity. this paper was showed that VCO system was enough usable in wireless network module. USN/RFID Reader module shows superior result that validity awareness distance corresponds to 30 M in the case of USN and to 5 M in RFID Reader's case and 900 MHz of commercial frequency does practical use enoughly in range of high frequency. The USN/RFID Reader module is considered to act big role to Ubiqitous industry offering computing surrounding of new concept that is intelligence type service and that was associated to real time location system(RTLS), environment improvement/supervision, national defense, traffic administration etc.

• New & Renewable Energy
• /
• v.5 no.4
• /
• pp.34-37
• /
• 2009

Using six SMD(surface mount device) type AlGaAs/GaAs single junction solar cells connected in series, a power source was fabricated for a white GaN LED. The electrical properties of the power source was measured and analyzed under one sun (100mW/$cm^2$) and various indoor light (300 - 900 lux) conditions. Under 600 lux indoor light condition, output power was 17.06 ${\mu}W$ and it was 30.75 ${\mu}W$ under 900 lux indoor light condition. Using the fabricated solar cell power supply, we have turned on the white GaN LED. It was worked well under 15 ${\mu}W$(at 480 lux) power supplied from solar cell array. This kind of solar cell power supply can be used as a power source for ubiquitous sensor network (USN).

• International journal of advanced smart convergence
• /
• v.7 no.4
• /
• pp.161-168
• /
• 2018

Recently, the bio-sensing information systems for collecting and analysing human body information of a patient in real time in the field of medical information and healthcare information service are continuously increasing. Specially, various wearable devices such as a wrist, a garment, and a skin attachment type for supporting health information of a mobile user are rapidly increasing. Until now, there is no patch-type biometric information service model. Therefore, this paper presents a biometric information system model and the application examples to support biometric information sensing and health information service of mobile user with digital patch system as a new biometric information system. As a result, through this research, research issues based on digital patch system are searched to suggest the direction of continuous research.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.20 no.6
• /
• pp.1136-1141
• /
• 2016

IoT technology has been used as a core technology of convergence service that needs intelligent information processing, and the importance is largely emerging now. And internal network construction thru IoT interaction device can connect with IoT device effectively, provide diverse services by connection with open platform. Especially, beacon that is based on low electric power bluetooth device is receiving attention as one of core technology of IoT. Beacon technology is utilized widly in various fields of industry, and there are lot of demands in the specific environment and conditions beyond the basic function. On this thesis, the authors are proposing the beacon device that utilized acceleration sensor and hole sensor. this beacon device can control the target on specific situation thru sensing of moving target. For the more, we will expect to apply to the various type of factory environments like detachable installation, optimized management using sensor.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.33 no.1
• /
• pp.55-61
• /
• 2020

Social infrastructure facilities that have been under construction since the country's high-growth period are undergoing rapid aging, and, thus, safety assessments of large structures such as bridge tunnels, which can be directly linked to large-scale casualties in the event of an accident, are necessary. It is difficult to construct economical and efficient wireless smart sensor networks that improve structural health monitoring (SHM) because the existing wire sensors have a short signal reach. However, low-power wide-area networks (LPWANs) are becoming popular within the Internet of Things, and enable economical and efficient SHM. In this study, the technology trends of a wireless measuring sensor based on LoRa LPWANs were investigated, and an installation and maintenance plan for this type of sensor is proposed.

• The Journal of the Korea Contents Association
• /
• v.11 no.2
• /
• pp.142-151
• /
• 2011

All medical information over sensor networks need to transmit and process securely in the u-Health services. The reliability of transmission between u-Health medical sensor devices and gateway is very important issue. When the user moves to other place with u-Health devices, its signal strength is going down and is far from the coverage of gateway. In this case, Malicious user can be carried out an intrusion under the situation. And also rogue gateway can be tried to steal medical information. Therefore, it needs mutual authentication between sensor devices and gateway. In this paper, we design a mutual authentication protocol which divided sessions from an authenticated session are updated periodically. And in order to reduce the traffic overhead for session authentication, we also introduce dynamic session management according to sampling rate of medical sensor type. In order to verify this, we implemented the programs for the test-bed, and got an overall success from three types of experiment.