• Journal of the Korea Institute of Military Science and Technology
• /
• v.19 no.1
• /
• pp.66-75
• /
• 2016

Stereoscopic image generated by depth image-based rendering(DIBR) for surveillance robot and camera is appropriate in a low bandwidth network. The image is very important data for the decision-making of a commander and thus its integrity has to be guaranteed. One of the methods used to detect manipulation is to check if the stereoscopic image is taken from the original camera. Sensor pattern noise(SPN) used widely for camera identification cannot be directly applied to a stereoscopic image due to the stereo warping in DIBR. To solve this problem, we find out a shifted object in the stereoscopic image and relocate the object to its orignal location in the center image. Then the similarity between SPNs extracted from the stereoscopic image and the original camera is measured only for the object area. Thus we can determine the source of the camera that was used.

• Journal of Sensor Science and Technology
• /
• v.27 no.6
• /
• pp.362-367
• /
• 2018

A complementary metal oxide semiconductor (CMOS) binary image sensor is proposed for low-power and low-noise operation. The proposed binary image sensor has the advantages of reduced power consumption and fixed pattern noise (FPN). A gate/body-tied (GBT) p-channel metal-oxide-semiconductor field-effect transistor (PMOSFET)-type photodetector is used as the proposed CMOS binary image sensor. The GBT PMOSFET-type photodetector has a floating gate that amplifies the photocurrent generated by incident light. Therefore, the sensitivity of the GBT PMOSFET-type photodetector is higher than that of other photodetectors. The proposed CMOS binary image sensor consists of a pixel array with $394(H){\times}250(V)$ pixels, scanners, bias circuits, and column parallel readout circuits for binary image processing. The proposed CMOS binary image sensor was analyzed by simulation. Using the dynamic comparator, a power consumption reduction of approximately 99.7% was achieved, and this performance was verified by the simulation by comparing the results with those of a two-stage comparator. Also, it was confirmed using simulation that the FPN of the proposed CMOS binary image sensor was successfully reduced by use of the double sampling process.

• The Journal of Korea Institute of Information, Electronics, and Communication Technology
• /
• v.16 no.6
• /
• pp.465-471
• /
• 2023

This paper proposes a comparator structure that improves the noise and output delay of a single-slope ADC(SS-ADC) used in CMOS Image Sensor (CIS). To improve the noise and delay characteristics of the output, a comparator structure using the miller effect is designed by inserting a capacitor between the output node of the first stage and the output node of the second stage of the comparator. The proposed comparator structure improves the noise, delay of the output, and layout area by using a small capacitor. The CDS counter used in the single slop ADC is designed using a T-filp flop and bitwise inversion circuit, which improves power consumption and speed. The single-slope ADC also performs dual CDS, which combines analog correlated double sampling (CDS) and digital CDS. By performing dual CDS, image quality is improved by reducing fixed pattern noise (FPN), reset noise, and ADC error. The single-slope ADC with the proposed comparator structure is designed in a 0.18-㎛ CMOS process.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.23 no.2
• /
• pp.89-92
• /
• 2010

A bolometer sensor used in an infrared thermal imaging system has many advantages on the process because it does not need a separate cooling system and its manufacturing is easy. However the sensitivity of the bolometer is low and the fixed pattern noise(FPN) is large, because the bolometer sensor is made by micro electro mechanical systems (MEMS). These problems can be fixed-by using the high performance readout integrated circuit(ROIC) with noise reduction techniques. In this paper, we propose differential delta sampling circuit to remove the mismatch noise of ROIC itself, the FPN of the bolometer. And for reduction of FPN noise, the reference signal compensation circuit which compensate the reference signal by using on-resistance of MOS transistor was proposed.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.59 no.11
• /
• pp.2058-2065
• /
• 2010

This paper presents the sensor location and step estimation algorithm for personal navigation system (PNS). PNS has the disadvantage in that the position of the sensor must be fixed on a human body. Three-axis acceleration sensor is used to solve the disadvantage and to consider the real situation. We simplify the measurement data by using the band pass filter, witch It has the advantage in the detection of characteristic point. Through the detected characteristic points, it is possible to setup the parameter for the pattern detection. Depending on the sensor location, the parameters have the different type of noise covariance. Particularly, when the position of the sensor is changed, the impulse noise shows up. Considering the noise, we apply the recursive least square algorithm using the variable forgetting factors, which can classify the sensor location based on the estimated parameters. We performed the experiment for the verification of the proposed algorithm in the various environments. Through the experimental results, the effectiveness of the proposed method is verified.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.06a
• /
• pp.148-149
• /
• 2008

As infrared light is radiated, the CMOS Readout IC (ROIC) for the microbolometer type infrared sensor detects voltage or current when the resistance value in the bolometer sensor varies. One of the serious problems in designing the ROIC is that resistances in the bolometer and reference resistor have process variation. This means that each pixel does not have the same resistance, causing serious fixed pattern noise problems in sensor operations. In this paper, Reference resistor compensation technique was proposed. This technique is to compensate the reference resistance considering the process variation, and it has the same reference resistance value as a bolometer cell resistance by using a comparator and a cross coupled latch.

• Proceedings of the IEEK Conference
• /
• 2002.06c
• /
• pp.43-46
• /
• 2002

This paper is about the Micro Accelerometer Sensor that collect the human's writing patterns so as to process its signals. Finally, we pursue the accuracy of digital data about the writing pattern and hope to discuss the possibility of the Micro Accelerometer Sensor Besides, we researched the compensation of signal distortion due to tiIt and analyzed the noise error in order to improve its accuracy.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.17 no.1
• /
• pp.110-119
• /
• 2017

This paper describes a CMOS image sensor (CIS) with dual correlated double sampling (CDS) and column-parallel analog-to-digital converter (ADC) and its measurement method using a field-programmable gate array (FPGA) integrated module. The CIS is composed of a $320{\times}240$ pixel array with $3.2{\mu}m{\times}3.2{\mu}m$ pixels and column-parallel 10-bit single-slope ADCs. It is fabricated in a $0.11-{\mu}m$ CIS process, and consumes 49.2 mW from 1.5 V and 3.3 V power supplies while operating at 6.25 MHz. The measured dynamic range is 53.72 dB, and the total and column fixed pattern noise in a dark condition are 0.10% and 0.029%. The maximum integral nonlinearity and the differential nonlinearity of the ADC are +1.15 / -1.74 LSB and +0.63 / -0.56 LSB, respectively.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.16 no.12 s.117
• /
• pp.1252-1261
• /
• 2006

This paper summarizes theoretical work on the multichannel decentralized feedback control of sound radiation from aircraft trim panels using piezoceramic actuators. The aircraft trim panels are generally honeycomb structures designed to meet the design requirement of low weight and high stiffness. They are resiliently-mounted to the fuselage for the passive reduction of noise transmission. It is motivated by the localization of reduction in vibration of single channel active trim panels. 12-channel decentralized feedback control systems are investigated in terms of the reduction of noise and vibration for three configurations of sensor actuator pairs. Local coupling of the closely-spaced sensor and actuator pairs was modeled using single degree of freedom systems. The multichannel control system is characterized using the state-space model. For the stability point of view, the relative stability or robustness is evaluated by comparing the real part of eigenvalues of the system matrix for the three configurations. The control performance is also evaluated and compared for the three configurations. It is found that the multichannel system can lead to the globalization of the reduction in vibration and radiated noise. It does not appear to yield a significant improvement in the vibration because of decreased gain margin. However, the reduction in the radiated noise is remarkably improved due to the variation of the vibration pattern with the actuation configurations.

• Journal of IKEEE
• /
• v.19 no.4
• /
• pp.486-490
• /
• 2015

Sensitivity characteristics of temperature sensor with $Bi_2Mg_{2/3}Nb_{4/3}O_7$ (BMNO) layer were investigated with low frequency noise measurement. Temperature sensor with BMNO layer had high reliability and high sensitivity comparing with conventional MOS type temperature sensor. Annealing temperature variation effects with $600^{\circ}C$, $700^{\circ}C$ and $800^{\circ}C$ were measured and analyzed. Annealing temperature determines trap distribution and $700^{\circ}C$ annealing sample has different pattern comparing with other samples. Results of low frequency noise can offer the design guide of temperature sensor performance.