• The Journal of the Convergence on Culture Technology
• /
• v.6 no.4
• /
• pp.825-831
• /
• 2020

In modern society, automobiles have become an essential means of transportation. It is the only consumable that is worn by contacting the ground among automobile parts. If the tyres are severely worn, the tyres may be break, presenting a risk of a serious accident to the driver. To avoid this risk, drivers should check tyre pressure and tread condition before driving a car. Tyre inflation pressure can be easily measured by TPMS, but in the case of tyre tread conditions, it can be cumbersome when the driver measures it directly using a coin or vernier caliper. This hassle can expose the driver to traffic accidents due to tyre breakage by neglecting to measure the condition of the tyre tread. In this paper, we introduce the contents of research to design an IoT service-based system that can automatically measure automobile tyres, and we verified the possibility of realizing the system by actually implementing and testing some components of the system.

• Tribology and Lubricants
• /
• v.30 no.3
• /
• pp.183-188
• /
• 2014

In this paper, we present our analysis of tribological failure examples for an anti-lock brake system(ABS) in a car. The study range of this paper is to improve the quality of ABS system by analyzing with sensor, computer, actuator and oil lines. In the first example, the brake leak from hydraulic supply line in a caliper on the rear left side of the ABS hydraulic modulator. This produces the sponge phenomenon, where the car does not brake even when the driver operates the brake pedal. The hydraulic unit operating ABS is actuator that play role regulating drive condition according with the oil pressure supplied with wheel of a car. In the second example, the service man does not completely tighten the fixed bolt after repairing the car. This causes the ABS warning lamp to light up as the ABS wheel speed sensor cannot detect whether the ABS has been activated. In the third example, the ABS electronic control unit is separated from the soldered part of the inner circuit board. Consequently, the ABS fails in control because the ABS motor pump receives no-signal for the hydraulic unit. The wheel speed sensor has to large durability because of giving signal of acting condition to computer by detected the acceleration and deceleration of wheel of a car. In the fourth example, the ABS warning lamp lights up of when cracks propagate in the circuit board soldering part. The circuit of this computer is very important part for input and output the operating signal of system. Such failures can aggravate the durability of the ABS. Thus, the ABS needs to be optimized to eliminate malfunction phenomenon.

• Journal of Sensor Science and Technology
• /
• v.28 no.3
• /
• pp.164-170
• /
• 2019

In this paper, a lane detection and tracking algorithm based on vision sensors and employing a robust filter for inner edge detection is proposed for developing a lane departure warning system (LDWS). The lateral offset value was precisely calculated by applying the proposed filter for inner edge detection in the region of interest. The proposed algorithm was subsequently compared with an existing algorithm having lateral offset-based warning alarm occurrence time, and an average error of approximately 15ms was observed. Tests were also conducted to verify whether a warning alarm is generated when a driver departs from a lane, and an average accuracy of approximately 94% was observed. Additionally, the proposed LDWS was implemented as an embedded system, mounted on a test vehicle, and was made to travel for approximately 100km for obtaining experimental results. Obtained results indicate that the average lane detection rates at day time and night time are approximately 97% and 96%, respectively. Furthermore, the processing time of the embedded system is found to be approximately 12fps.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.17 no.2
• /
• pp.34-41
• /
• 2009

The latest vehicle yields a superior safety and reduction of driving burden by monitoring the driving state of vehicle and its environment with various sensors. To detect other vehicles and objects of the rear left and right-side blind spot area of driver, provide the information about a existence of objects inside the blind spot, and give a signal to avoid collision, this study proposes the intelligent outside rear-view mirror system. This task has substantially complicated several factors. For example, the size, geometry and features of the various vehicles which might enter the monitored zone is varied widely and therefore present various reflective characteristics. This study proposes the optimal specification and configuration of optical system and IR array sensor of blind spot detection system, and shows the results of the performance evaluation of developed system.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.19 no.2
• /
• pp.72-77
• /
• 2011

In this paper, we propose effective diagnosis algorithm for hub bearing fault in driving vehicle using acceleration signal and wheel speed signal measured in hub bearing unit or knuckle. This algorithm consists of differential, envelope and power spectrum method. We developed diagnosis system for realizing proposed algorithm. This system consists of input device including acceleration sensor and wheel speed sensor, calculation device using Digital Signal Processor (DSP) and display device using Personal Digital Assistant (PDA). Using this diagnosis system, a driver can see hub bearing fault(flaking) from the vibration in driving vehicle. With early repairing, he can keep good ride feeling and prevent accident of vehicle resulting from hub bearing fault.

• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.20 no.1
• /
• pp.174-192
• /
• 2021

The LIDAR sensor, which provides higher cognitive performance than cameras and radar, is difficult to apply to ADAS or autonomous driving because of its high price. On the other hand, as the price is decreasing rapidly, expectations are rising to improve existing autonomous driving functions by taking advantage of the LIDAR sensor. In level 3 autonomous vehicles, when a dangerous situation in the cognitive module occurs due to a sensor defect or sensor limit, the driver must take control of the vehicle for manual driving. If the driver does not respond to the request, the system must automatically kick in and implement a minimum risk maneuver to maintain the risk within a tolerable level. In this study, based on this background, a LIDAR-based LKS MRM algorithm was developed for the case when the normal operation of LKS was not possible due to troubles in the cognitive system. From point cloud data collected by LIDAR, the algorithm generates the trajectory of the vehicle in front through object clustering and converts it to the target waypoints of its own. Hence, if the camera-based LKS is not operating normally, LIDAR-based path tracking control is performed as MRM. The HAZOP method was used to identify the risk sources in the LKS cognitive systems. B, and based on this, test scenarios were derived and used in the validation process by simulation. The simulation results indicated that the LIDAR-based LKS MRM algorithm of this study prevents lane departure in dangerous situations caused by various problems or difficulties in the LKS cognitive systems and could prevent possible traffic accidents.

• KSII Transactions on Internet and Information Systems (TIIS)
• /
• v.14 no.2
• /
• pp.757-770
• /
• 2020

We propose a hand gesture recognition method that is compatible with a head-up display (HUD) including small processing resource. For fast link adaptation with HUD, it is necessary to rapidly process gesture recognition and send the minimum amount of driver hand gesture data from the wearable device. Therefore, we use a method that recognizes each hand gesture with an inertial measurement unit (IMU) sensor based on revised correlation matching. The method of gesture recognition is executed by calculating the correlation between every axis of the acquired data set. By classifying pre-defined gesture values and actions, the proposed method enables rapid recognition. Furthermore, we evaluate the performance of the algorithm, which can be implanted within wearable bands, requiring a minimal process load. The experimental results evaluated the feasibility and effectiveness of our decomposed correlation matching method. Furthermore, we tested the proposed algorithm to confirm the effectiveness of the system using pre-defined gestures of specific motions with a wearable platform device. The experimental results validated the feasibility and effectiveness of the proposed hand gesture recognition system. Despite being based on a very simple concept, the proposed algorithm showed good performance in recognition accuracy.

• Journal of KIISE:Computing Practices and Letters
• /
• v.12 no.2
• /
• pp.91-101
• /
• 2006

Researches on services of vehicles have been mainly focused on how to provide useful information and entertainment for an in-vehicle driver. However, the needs are appreciably increased for more advanced services that help drivers to check and manage their vehicles conveniently, without requiring drivers to attach to their vehicles. It is a sort of ubiquitous computing, providing an intelligent interactive services for human at any time and any where. In this paper, we present an intelligent vehicle information system to enable a driver to remotely diagnose and control a vehicle via CDMA communication network connected to the Internet. The system improves mobility for diagnosis and control of vehicle by implementing a cut and call back mechanism, which allows the vehicle terminal to have access to the information server on the Internet via CDMA call. No matter where the driver is, he can obtain the remote diagnosis and control services on the web browser without any additional application installation. Design methodology is introduced and evaluation results are analyzed for the CDMA-based intelligent vehicle information system. The experimental results show that the response time of the vehicle terminal to a web client request is 10.302 seconds at the beginning and 646.44ms thereafter. The average response time of CAN sensor node to a vehicle terminal request is 6.669ms.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.24 no.1
• /
• pp.16-23
• /
• 2016

The EWB(electronic wedge brake) is one in which the braking force is developed in a wedge and caliper system and applied to a disk and wedge mechanism. The advantage of the wedge structure is that it produces self-reinforcing effect and hence, utilizes minimal motor power, resulting in reduced gear and current. The extent of use of clamping force sensors and protection from failure of the EWB system directly depends on the level of vehicle mass production. This study investigated the mathematical equations, simulation modeling, and failsafe control algorithm for the clamping force sensor of the EWB and validated the simulations. As this EWB system modeling can be applied to motor inductance, resistance, screw inertia, stiffness, and wedge mass and angle, this study could improve the accuracy of simulation of the EWB. The simulation results demonstrated the braking force, motor speed, and current of the EWB system when the driver desired to the step and pulse the brake force inputs. Moreover, this paper demonstrated that the proposed failsafe control algorithm accurately detects faults in the clamping force sensor, if any.

• Journal of Biosystems Engineering
• /
• v.18 no.1
• /
• pp.37-47
• /
• 1993

This study was conducted to develop the on-line monitoring system for plant growth responses. The system consisted of two parts. One system was the measuring system and the other was its controlling system. The established measuring systems were the ultrasonic wave sensor driver for height of plant, the potentiometer for diameter of plant stem, and the weighing system with strain gage application for plant weight. Also, computer program for measurement and controlling was developed, and the whole system was tested by the fabricated plant, and the actual plant growth responses were monitored by the system. When monitoring the actual plant growth responses, even the small amount of plant growth resposes could be measured by the system within tolerable error ranges.