• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1997.04a
• /
• pp.491-495
• /
• 1997

In this paper, an effective mount design method using vector synthesis is presented for two mount systems. For designing mount stiffnesses effectively, we perform a sensitivity analysis, i.e, identify the contribution rate of an input component vector to the total output vector. Especially, we show that it is necessary to takea phase sensitivity into consideration in case of two mount systems, such as the excavator mount systems having engine mounts and cabin mounts. THe proposed method is testified is testified through an test bed.

• Korean Journal of Optics and Photonics
• /
• v.5 no.3
• /
• pp.379-385
• /
• 1994

The sensitivity vector which depends on geometry of object illumination angles and distances of ESPI was analyzed. And the sensitivities of in-plane and out-of-plane displacements have been investigated. From these results, we have the conclusion that it is useful to use the diverging beam for object illumination. With diverging object illumination, only little errors are occurred when we approximate the sensitivity vector to constant all over the object surface.urface.

• Bulletin of the Korean Mathematical Society
• /
• v.49 no.2
• /
• pp.249-262
• /
• 2012

In this paper, under some suitable conditions and in virtue of a selection which depends on a vector-valued function and a feasible set map, the sensitivity analysis of a class of implicit multifunctions is investigated. Moreover, by using the results established, the solution sets of parametric vector optimization problems are studied.

• Tribology and Lubricants
• /
• v.40 no.2
• /
• pp.39-46
• /
• 2024

The Morton effect (ME) is an instability phenomenon occurring in rotating machineries supported by fluid film bearings and is induced by the thermal deformation of the overhung mass, which is a part of the rotating shaft. Herein, we describe the ME during the high-speed balancing test of a 20 MW class steam turbine. Additionally, to predict the rotating speed at which the ME occurs, we apply the sensitivity vector theory for the steam turbine. During the operation of the steam turbine, we observe a continuous increase in vibration and hysteresis near the rated speed, which is typical of the ME. Increasing the temperature of the lubricating oil supplied to the bearings from 40 to 60℃ suppresses the occurrence of the ME. The rotordynamic analysis for the steam turbine suggests the existence of a mode in which the overhung mass undergoes significant deformation near the rated speed, and we presume that such a mode will increase the occurrence of the ME. The predicted rotating speed of ME occurrence, obtained through the sensitivity vector method, correlates with the test results. Moreover, increasing the temperature of the supplied lubricating oil mitigates the occurrence of ME by reducing the sensitivity between the temperature deviation vector and unbalance mass vector.

• Proceedings of the IEEK Conference
• /
• 2001.09a
• /
• pp.389-392
• /
• 2001

A motion vector sensitivity function for abrupt scene change detection is presented. Proposed function detects a scene change by a static uni-value, not using threshold comparion method in real time and compressed domain. All abrupt scene change was detected.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.5 no.4
• /
• pp.171-178
• /
• 1997

Vehicle interior noise has become increasingly important in this recent years. The noise of a vehicle is one of the important problems in a vehicle design. The interior noise is caused by various vibration sources of vehicle compartment. The booming noise of a vehicle can be significantly affected by vibrations transmitted from engine excitation forces to the vehicle body. Specially, we are interested in the state of transmission paths such as engine mounts to reduce noise in a vehicle compartment. In this paper, we have been calculated the contribution of each transmission path such as engine mounts to interior noise. To identify contribution of each input sources and transmission paths to output, the effectiveness of each input component to output is calculated. Sensitivity analysis is carried out for investigation of contribution to output due to input variations. With the simulation of magnitude and phase change of inputs using vector synthesis diagram, the trends of synthesized output vector are obtained. As a result, we suggested sensitivity analysis of vector synthesis as a technique of prediction and control for noise in a vehicle compartment.

• Journal of Electrical Engineering and Technology
• /
• v.11 no.2
• /
• pp.320-328
• /
• 2016

The introduction of renewable energy sources into the AC grid can change and weaken the strength of the grid, which will in turn affect the stability and robustness of the doubly-fed induction generator (DFIG) wind farm. When integrated with weak grids, the DFIG wind turbine with vector power control often suffers from poor performance and robustness, while the DFIG wind turbine with synchronized control provides better stability. This paper investigates the critical short circuit ratios of DFIG wind turbine with vector power control and synchronized control, to analyze the stability boundary of the DFIG wind turbine. Frequency domain methods based on sensitivity and complementary sensitivity of transfer matrix are used to investigate the stability boundary conditions. The critical capacity of DFIG wind farm with conventional vector power control at a certain point of common coupling (PCC) is obtained and is further increased by employing synchronized control properly. The stability boundary is validated by electromagnetic transient simulation of an offshore wind farm connected to a real regional grid.

• Proceedings of the KIEE Conference
• /
• 2001.07d
• /
• pp.2246-2248
• /
• 2001

This paper presents a new vector control scheme for induction motor. An exact knowledge of the rotor flux position is essential for a high-performance vector control. The position of the rotor flux is measured in the direct schemes and estimated in the indirect schemes. Since the estimation of the flux position requires a priori knowledge of the induction motor parameters, the indirect schemes are machine parameter dependent. The rotor and stator resistance among the parameters change with temperature. Variations in the parameters of induction machine cause deterioration of both the steady state and dynamic operation of the induction motor drive. Several methods have presented to minimize the consequences of parameter sensitivity in indirect scheme. In this paper, new estimation scheme of rotor flux position is presented to eliminate sensitivity due to variation in the resistance. The simulation is executed to verify the proposed vector control performance and to compare its performance with that of indirect and direct vector control.

• International Journal of Aeronautical and Space Sciences
• /
• v.16 no.3
• /
• pp.437-444
• /
• 2015

Satellite selection and exclusion techniques have been applied to the global navigation satellite system (GNSS) with the aim of achieving a balance between navigational performance and computational efficiency. Conventional approaches to satellite selection based on the best dilution of precision (DOP) are excessively computational and complicated. This paper proposes a new method that applies a geometric sensitivity index of individual GNSS satellites. The sensitivity index is derived using the inner product of the line of sight (LOS) vector of each satellite. First, the LOS vector is computed, which accounts for the geometry between the satellite and user positions. Second, the inner product of each pair of LOS vectors is calculated, which indicates the proximities of the satellites to one another. The proximity can be determined according to the sensitivity of each satellite. A post-processing test was conducted to verify the reliability of the proposed method. The proposed index and the results of a conventional approach that measures the dilution of precision (DOP) were compared. The test results demonstrate that the proposed index produces results that are within 96% of those of the conventional approach and reduces the computational burden. This index can be utilized to estimate the sensitivity of individual satellites, obtaining a navigation solution. Therefore, the proposed index applies to satellite selection and exclusion as well as to the sensitivity analyses of multiple GNSS applications.

• Proceedings of the KSR Conference
• /
• 2000.11a
• /
• pp.680-687
• /
• 2000

In this paper we present a new vector control scheme for induction motor. An exact knowledge of the rotor flux position is essential for a high-performance vector control. The position of the rotor flux is measured in the direct scheme or estimated in the indirect schemes. Since the estimation of the flux position requires a priori knowledge of the induction motor parameters, the indirect schemes are machine parameter dependent. The rotor resistance and stator resistance among the parameters change with temperature. Variations in the parameters of induction machine cause deterioration of both the steady state and dynamic operation of the induction motor drive. Several methods have been presented to minimize the consequences of parameter sensitivity in indirect scheme. In this paper new estimation scheme of rotor flux position is presented to eliminate sensitivity due to resistance change with temperature. Simulation results are used to verify the performance of the proposed vector control scheme.