• The Journal of Advanced Prosthodontics
• /
• v.9 no.2
• /
• pp.85-92
• /
• 2017

PURPOSE. The aim of this study was to evaluate the effect of tooth surface pre-treatment steps on shear bond strength, which is essential for understanding the adhesive cementation process. MATERIALS AND METHODS. Shear bond strengths of different cements with various tooth surface treatments (none, etching, priming, or etching and priming) on enamel and dentin of human teeth were measured using the Swiss shear test design. Three adhesives (Permaflo DC, Panavia F 2.0, and Panavia V5) and one self-adhesive cement (Panavia SA plus) were included in this study. The interface of the cement and the tooth surface with the different pre-treatments was analyzed using SEM. pH values of the cements and primers were measured. RESULTS. The highest bond strength values for all cements were achieved with etching and primer on enamel ($25.6{\pm}5.3-32.3{\pm}10.4MPa$). On dentin, etching and priming produced the highest bond strength values for all cements ($8.6{\pm}2.9-11.7{\pm}3.5MPa$) except for Panavia V5, which achieved significantly higher bond strengths when pre-treated with primer only ($15.3{\pm}4.1MPa$). Shear bond strength values were correlated with the micro-retentive surface topography of enamel and the tag length on dentin except for Panavia V5, which revealed the highest bond strength with primer application only without etching, resulting in short but sturdy tags. CONCLUSION. The highest bond strength can be achieved for Panavia F 2.0, Permaflo DC, and Panavia SA plus when the tooth substrate is previously etched and the respective primer is applied. The new cement Panavia V5 displayed low technique-sensitivity and attained significantly higher adhesion of all tested cements to dentin when only primer was applied.

• Journal of Electrical Engineering and Technology
• /
• v.4 no.4
• /
• pp.546-551
• /
• 2009

In this paper, we describe a self-aligned fabrication method for a nano-patterned bottom electrode using flood exposure from the backside. Misalignments between layers could cause the final devices to fail after the fabrication of the nano-scale bottom electrodes. A self-alignment was exploited to embed the bottom electrode inside the glass substrate. Aluminum patterns act as a dry etching mask to fabricate glass trenches as well as a self-aligned photomask during the flood exposure from the backside. The patterned photoresist (PR) has a negative sidewall slope using the flood exposure. The sidewall slopes of the glass trench and the patterned PR were $54.00^{\circ}$ and $63.47^{\circ}$, respectively. The negative sidewall enables an embedment of a gold layer inside $0.7{\mu}m$ wide glass trenches. Gold residues on the trench edges were removed by the additional flood exposure with wet etching. The sidewall slopes of the patterned PR are related to the slopes of the glass trenches. Nano-scale bottom electrodes inside the glass trenches will be used in beam resonators operating at high resonant frequencies.

• Journal of the Korean Ceramic Society
• /
• v.40 no.2
• /
• pp.153-158
• /
• 2003

Self-patterning of thin films using photosensitive sol solution has advantages such as simple manufacturing process compared to photoresist/dry etching process. In this study,$La_{0.5}SR_{0.5}CoO_3$(LSCO) thin films as an electrode material for ferroelectric memories have been prepared by spin coating method using photosensitive sol solution. La-2methoxyethoxide, Sr-ethoxide, Co-2methoxyethoxide were used as starting materials. As UV exposure time to the LSCO gel thin film increased, the UV absorption peak intensity of metal${beta}$-diketonate decreased due to reduced solubility by M(metal)-O-M bond formation. Solubility difference by UV irradiation on LSCO gel thin film allows to obtain a fine patterning of thin film. The LSCO thin films annealed over$680{\circ}C$ in air showed perovskite phase and the lowest resistivity$(4{ imes}10^{-3}{Omega}cm)$ of the thin films were obtained by annealing at$740{\circ}C$.

• Journal of the Korean Ceramic Society
• /
• v.39 no.8
• /
• pp.750-757
• /
• 2002

Self-patterning of thin films using photosensitive sol solution has advantages such as simple manufacturing process compared to photoresist/dry etching process. In this study, ferroelectric $Sr_{0.9}Bi_{2.1}Ta_2O_9$ thin films have been prepared by spin coating method using photosensitive sol solution. Strontium ethoxide, tertramethylheptanedionato bismuth and tantalum ethoxide were used as starting materials. As UV exposure time to the SBT thin film increased, the UV absorption peak intensity of metal ${\beta}$-diketonate decreased due to reduced solubility by M-O-M bond formation. Solubility difference by UV irradiation on SBT thin film allows to obtain a fine patterning of thin film. Also, The ferroelectric properties of the UV irradiated SBT thin films were superior to those of the no-UV irradiated films.

• The Journal of the Korean dental association
• /
• v.53 no.3
• /
• pp.187-194
• /
• 2015

This paper reflects on the state of the art of two kinds of tooth hard tissue (enamel and dentin) bonding with resin cement. After presenting composition of resin cement, concepts of enamel bonding and resin bonding are addressed. Special attention is devoted to the concept and advantage of self-etching technique. Finally, recommended clinical performance regarding bonding to tooth with resin cement is summarized.

• Proceedings of the KACD Conference
• /
• 2002.11a
• /
• pp.712-712
• /
• 2002

No Abstract, See Full Text

• Proceedings of the KACD Conference
• /
• 2002.11a
• /
• pp.710-710
• /
• 2002

No Abstract, See Full Text

• Proceedings of the KACD Conference
• /
• 2002.11a
• /
• pp.706-706
• /
• 2002

No Abstract, See Full Text

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2006.10a
• /
• pp.509-510
• /
• 2006

• Proceedings of the Materials Research Society of Korea Conference
• /
• 1998.08a
• /
• pp.99.3-99
• /
• 1998