• 한국표면공학회지
• /
• 제44권1호
• /
• pp.32-37
• /
• 2011

Numerical analysis is done to investigate the effect of surface treatment of a toilet on the cleanness. The surface treatment using plasma for the super-hydrophobic surface expects the self-cleaning effect of the toilet seat cover for preventing the droplets with a great quantity of bacteria during the toilet flushing after evacuation. In this study, the fluid analysis in the toilet during the flushing was performed by an ultrahigh-speed CCD camera with 1,000 frame/sec and the numerical modeling. And the spattering phenomenon from the toilet surface during urine was analyzed quantitatively by CFD-ACE+ with a free surface model and a mixed model of two fluids. If the surface tension of the toilet surface is weak, many urine droplets after collision bounded in spite of considering the gravity. The turbulence generated by the change of angle and velocity of urine and the variation of the collision phenomenon from toilet surface were modeled numerically.

• 한국표면공학회:학술대회논문집
• /
• 한국표면공학회 2018년도 춘계학술대회 논문집
• /
• pp.94-94
• /
• 2018

무인자동차 및 전기자동차 등 전장부품 및 메인보드에서의 오염 방지와 전자파에 의한 신호 간섭 현상에 따른 기기의 오작동을 방지하고자 MWCNT의 clustering 및 tangling현상을 활용하여 self cleaning 기능을 갖는 super hydrophobic 표면과 high aspect ratio에 의한 percolation 현상을 활용하여 전자파 차폐를 위한 낮은 표면저항을 만족하는 복합 재료로 구성된 코팅에 관하여 연구하였다. 이를 위해 isopropyl alcohol(IPA)을 용매로 산처리 한 MWCNT와 무기바인더, 불소계 실란을 첨가하여 초음파 분산을 함으로써 코팅액을 제조하였다. 이를 full cone nozzle type, 흡상식 스프레이 조건으로 알루미늄 시편위에 스프레이 코팅 후 열경화 하여 접촉각측정기로 측정 결과 $160^{\circ}$이상의 초발수 표면과 Low Resistivity Meter로 표면저항을 측정한 결과 $10^3{\Omega}/cm^2$ 이하의 낮은 코팅막을 구현하였으며 내구성 실험을 위한 항온항습 장비로 $80^{\circ}C$의 내열테스트 및 80%와 $80^{\circ}C$조건하에서의 내습테스트 결과 표면에 이상 없음을 확인하였고 열전도율 측정을 위해 밀도 측정 결과 $2.68g/cm^3$, 비열 측정 결과 $0.85J/g^{\circ}C$가 열확산율 측정결과 $88.64mm^2/s$가 측정 되었으며 밀도, 비열, 열확산율을 곱한 값인 $201.9W/m{\cdot}K$의 열전도를 갖는 코팅막을 구현하였다.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2011년도 제40회 동계학술대회 초록집
• /
• pp.496-496
• /
• 2011

A very simple and cost-effective method for fabrication of SiOx-incorporated diamond-like carbon (DLC) thin films at a preparation temperature of less than $200^{\circ}C$ was developed. Since DLC coating can be prepared not under vacuum but atmospheric conditions without any carrier gas flow, not only wafers but also powderic substrates can be used for DLC coating. Formation of DLC coating could result in appearance of superhydrophobic behaviors, which was sustained in a wide range of pH (1~14). DLC-coated surfaces selectively interacted with toluene in a toluene/water mixture. These results imply that our preparation method of the DLC coating can be useful in many application fields such as creating self-cleaning surfaces, and water and air purification filters.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2013년도 제44회 동계 정기학술대회 초록집
• /
• pp.292-292
• /
• 2013

최근, 자연의 기능성 표면을 모사하여 우리 생활에 응용하기 위한 연구가 활발하다. 초-발수 특성을 가지는 대표적인 예인 연꽃잎은 마이크로-나노 크기의 거친 미세돌기(papillae)를 가지고 있으며 그 위에 낮은 표면 에너지를 가지는 왁스(wax)가 발달 되어 항상 깨끗한 상태를 유지한다. 본 실험에서는 이를 모사하여 RIE (Reactive Ion Etching)방법을 이용하여 기판인 Poly silicon wafer를 Sf6가스를 사용하여 Metal mash로 거칠기를 만들어 주었고, RF-magnetron sputtering 장치를 사용하여 $6{\times}10^{-3}$ Torr의 진공도에서 낮은 표면에너지를 가지는 PTFE (polytetrafluoroethylene)를 증착하여 표면 구조와 발수특성에 대하여 조사하였다. SSME(Surface shape measurement equipment)측정결과 0.24~0.36 um RSa 값이 측정되었고, 12 uL의 Di-water로 접촉각을 측정 한 결과 RIE 10분 처리를 한 기판 위에 PTFE를 3분 증착하였을 때 가장 높은 $153^{\circ}$의 초-발수 특성이 나타났으며, 4주의 시간이 지났을 때에도 접촉각이 유지가 되었다. XPS 측정결과 초-발수 표면에서 나타나는 CF2와 CF3 피크 값이 측정되었다. Reactive Ion Etching을 이용한 PTFE 발수 특성은 방수, 스마트 윈도우, 자가세정(Self-Cleaning), 디스플레이 표시장치, 김서림 방지(Anti-Fogging), 대전방지 코팅 등에 다각적으로 응용 가능할 것이라 사료된다.

• 전기학회논문지P
• /
• 제66권2호
• /
• pp.94-97
• /
• 2017

A method of improving the anti-fouling characteristics of porcelain insulators was proposed in this study. Functional coating was performed as a method of reducing the surface contamination of the porcelain insulators. The functional coating was applied on a ceramic substrate, which has the same material as the porcelain insulators. After coating the ceramic substrate 2, 3, 4, and 5 times alternately in the horizontal and vertical directions, the surface characteristics according to the thickness of the coating film were analyzed. The optimal process was selected to coat the surfaces of the post insulators and long rod insulators, which are the representative porcelain insulators. After coating, heat treatment was performed for 1 hour at $200^{\circ}C$ in a furnace to secure the durability of the coating film. Compared to the uncoated insulators, the insulators with the functional coating showed significantly improved anti-fouling characteristics as well as excellent adhesion to the coated insulator surface.

• 대한기계학회논문집B
• /
• 제24권7호
• /
• pp.1002-1009
• /
• 2000

Among the various types of diesel after-treatment device, the corona discharge reactor may be considered as a powerful process for trapping submicron particles. But after precipitation on the electrodes occurs, the reentrainment of particles is severe and often causes low or negative precipitation efficiency. Experiments were performed to investigate the effect of an applied voltage on the reentrainment of soot particles from the electrodes. A co-annular laminar diffusion flame burner was used as the soot generator. When a highly negative voltage was applied, exfoliation of the deposited soot particles and an increase in concentration of particles smaller than approximately 150 nm were observed. Turbulence induced from the negative tuft corona and sputtering caused particle reentrainment from the corona wire and from plates as well. Under soot laden combustion gas, a streamer corona often occurred in the wire-cylinder reactor. Because of its transient nature, streamer corona violently increased the concentration of reentrained particles and CO gas.

• 대한기계학회논문집A
• /
• 제31권6호
• /
• pp.679-685
• /
• 2007

Superhydrophobic surface, with a water contact angle greater than $150^{\circ}$, has a self-cleaning effect termed 'Lotus effect'. This surface is created by the combination of rough surface and the low surface energy. We proposed square pillar and square shapes to control surface roughness. Microstructure arrays are fabricated by DRIE(Deep Reactive Ion Etching) process and followed by PPFC(Plasma Polymerized Fluorocarbon) deposition. On the experimental result, contact angle at square pillar arrays is well matched with Cassie's model and largest contact angle is $173.37^{\circ}$. But contact angle of square pore shape arrays is lower than Cassie's theoretical contact angle about $5{\sim}10%$. Nevertheless, square pore arrays have more rigidity than square pillar arrays.

• Journal of Industrial and Engineering Chemistry
• /
• 제68권
• /
• pp.387-392
• /
• 2018

Various technical approaches and concepts have been proposed to develop conductive super-hydrophobic (SH) surfaces. However, most of these approaches are not usable in practical applications because of insufficient adhesion and cost issues. Additionally, durability and uniformity issues are still in need of improvement. The goal of this research is to produce a large-area conductive SH surface with improved adhesion performance and uniformity. To this end, carbon nanotubes (CNT) with a high aspect ratio and elastomeric polymer were utilized as a conductive filler and matrix, respectively, to form a coating layer. Additionally, nanoscale silica particles were utilized for stable implementation of the conductive SH surface. To improve the adhesion properties between the SH coating layer and substrate, pretreatment of the substrate was conducted by utilizing both wet and dry etching processes to create specific organic functional groups on the substrate. Following pretreatment of the surface, a zirco-aluminate coupling agent was utilized to enhance adhesion properties between the substrate and the SH coating layer. Raman spectroscopy revealed that adhesion was greatly improved by the formation of a chemical bond between the substrate and the SH coating layer at an optimal coupling agent concentration. The developed conductive SH coating attained a high electromagnetic interference (EMI) shielding effectiveness, which is advantageous in self-cleaning EMI shielding applications.

• 한국표면공학회지
• /
• 제52권1호
• /
• pp.37-42
• /
• 2019

Electrodeposited zinc layer is widely used as a sacrificial anode for a corrosion protection of steel. In this study, we modified the surface of electrodeposited zinc to have a hydrophobicity, which shows various advanced functionalities, such as anti-corrosion, anti-biofouling, anti-icing and self-cleaning, due to its repellency to liquids. Superhydrophobicity was realized on electrodeposited zinc layer with a hydrothermal treatment, creating nanostructures on the surface, and following Teflon coating. The superhydrophobic surface shows a great repellency to water with high surface tension, while liquid droplets with low surface tension easily adhered on the superhydrophobic surface. However, immiscible lubricant-impregnated superhydrophobic surface shows a great repellency to various liquids, regardless of their surface tension. Therefore, it is expected that the lubricant-impregnated surface can be an alternative of superhydrophobic surface, which have a drawback for some liquids with a low surface tension.

• Design & Manufacturing
• /
• 제15권4호
• /
• pp.57-64
• /
• 2021

In recent materials industry, researches on the technology to manufacture super hydrophobic surface by effectively controlling the wettability of solid surface are expanding. Research on the fabrication of super hydrophobic surface has been studied not only for basic research but also for self-cleaning, anti-icing, anti-friction, flow resistance reduction in construction, textile, communication, military and aviation fields. A super hydrophobic surface is defined as a surface having a water droplet contact angle of 150 ° or more. The contact angle is determined by the surface energy and is influenced not only by the chemical properties of the surface but also by the rough structure. In this paper, maskless lithography using DMD, electro etching, anodizing and hot embossing are used to make the polymer resin PMMA surface super hydrophobic. In the fabrication of microstructure, DMDs are limited by the spacing of microstructure due to the structural limitations of the mirrors. In order to overcome this, maskless lithography using a transfer mechanism was used in this paper. In this paper, a super hydrophobic surface with micro and nano composite structure was fabricated. And the wettability characteristics of the micro pattern surface were analyzed.