• Journal of Power Electronics
• /
• v.17 no.1
• /
• pp.106-114
• /
• 2017

In this paper, the Selective Harmonic Mitigation-PWM (SHM-PWM) method is used in single-phase and three-phase Cascaded H-Bridge (CHB) inverters in order to fulfill different power quality standards such as EN 50160, CIGRE WG 36-05, IEC 61000-3-6 and IEC 61000-2-12. Non-equal DC link voltages are used to increase the degrees of freedom for the proposed SHM-PWM technique. In addition, it will be shown that the obtained solutions become continuous and without sudden changes. As a result, the look-up tables can be significantly reduced. The proposed three-phase modulation method can mitigate up to the 50th harmonic from the output voltage, while each switch has just one switching in a fundamental period. In other words, the switching frequency of the power switches are limited to 50 Hz, which is the lowest switching frequency that can be achieved in the multilevel converters, when the optimal selective harmonic mitigation method is employed. In single-phase mode, the proposed method can successfully mitigate harmonics up to the 50th, where the switching frequency is 150 Hz. Finally, the validity of the proposed method is verified by simulations and experiments on a 9-level CHB inverter.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.20 no.10
• /
• pp.35-40
• /
• 2006

In this paper, a current-mode analog variable finite-impulse-response (FIR) filter with variable tap coefficient circuits is proposed for frequency selective wireless personal area network(WPAN) system or terminals. From the circuit simulation the operation of the 7-tap FIR filter is confirmed. The 0.0625-step tap coefficient circuit is designed and fabricated with $0.8[{\mu}m]$ CMOS technology. The proposed FIR filter has a variable length of taps and variable coefficients, so it has a potential for being used to frequency selective WPAN system or frequency selective wireless communication terminals.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.36 no.6C
• /
• pp.403-411
• /
• 2011

This paper addresses a cooperative transmission scheme based on Alamouti coding for cognitive radio networks over frequency selective fading channels. In the proposed scheme, the Alamouti coded form at the destination node is constructed through a simple combination of symbols at the source node, instead of the time-reversal operation and the conjugate operation at the relay nodes used in the conventional scheme. Numerical results show that the proposed scheme achieves a higher order cooperative diversity than that of the conventional scheme.

• Journal of Communications and Networks
• /
• v.5 no.2
• /
• pp.141-149
• /
• 2003

In this paper, we investigate design criteria and the performance of the space-frequency bit-interleaved coded modulation (SF-BICM) systems in frequency-selective Rayleigh fading channels. To determine the key parameters that affect the performance of SF-BICM, we derive the pairwise error probability (PEP) in terms of the determinant of the matrix corresponding to any two codewords. We prove that the bit-interleavers do the function of distributing the nonzero bits uniformly such that two or more nonzero bits are seldom distributed into the symbols that are transmitted in the same frequency bin. This implies that the bit-interleavers transform an SF-BICM system into an equivalent 1-antenna system. Based on this, we present design criteria of SFBICM systems that maximizes the diversity order and the coding gain. Then, we analyze the performance of SF-BICM for the case of 2-transmit antennas and 2-multipaths by deriving a frame error rate (FER) bound. The derived bound is accurate and requires only the distance spectrum of the constituent codes of SF-BICM. Numerical results reveal that the bound is tight enough to estimate the performance of SF-BICM very accurately.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.15 no.6
• /
• pp.779-785
• /
• 2012

In this paper, we have analyzed the curvature effects of the finite FSS(frequency selective surface) using the 3-D method of moment using the BiCGSTab algorithm as an iterative method. To validate the analysis method in this paper, we compared the RCS(radar cross section) of PEC(perfect electric conductor) sphere with theoretical results and it shows well agreements. The tripole slot FSSs which have many application in military were selected for the investigation of curvature effect and RCS as a frequency characteristics were observed with the variation of the curvature rate. Simulation results shows that curvature effect can significant effect the passband frequency and bandwidth of FSS. We suggest that the curvature effect must be considered at the stage of design FSS application like FSS radome.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.26 no.6
• /
• pp.475-481
• /
• 2013

The residual stresses occur in the Frequency Selective Surface(FSS) embedded hybrid composite structures after co-curing due to mismatch among the coefficient of thermal expansions and stiffness values between the FSS and composite materials. The spring backs occur due to these residual stresses. Therefore, in this paper, the spring-backs caused by residual stresses in FSS embedded composite structures were studied with considering effect of symmetric and unsymmetric stacking sequence of composite laminates.

• Physical Therapy Rehabilitation Science
• /
• v.10 no.4
• /
• pp.387-397
• /
• 2021

Objective: The purpose of this case study was to investigate selective region high-frequency diathermy at trigger points with therapeutic exercises on pain, function, balance and gait in older patients with degenerative knee osteoarthritis (DKO). Design: A case report. Methods: The patient who participated in this study was a 71-year-old woman, who had been diagnosed with moderate osteoarthritis with grade II Kellgren & Lawrence grading scale. The intervention consisted of selective region high-frequency diathermy at trigger points, with hip and knee stretching and strengthening exercises. The participant was given assessments before and after every intervention session using the Visual Analogue Scale (VAS), Western Ontario and McMaster Universities Arthritis Index (WOMAC), the Timed Up and Go test (TUG) and the 10 Meter Walk Test (10MWT). The participant performed the intervention 18 times for a total of 30 minutes each. Results: As a result of this study, the patient VAS decreased to 3 points, and the WOMAC decreased to 53 points. In addition, the TUG decreased to 3.25 s and the 10MWT decreased to 1.14 s. Conclusions: The results of this study suggest that selective region high-frequency diathermy at trigger points with therapeutic exercises may be an effective intervention to decrease pain, improve knee function, balance and gait in patients with DKO. The selective region high-frequency diathermy with therapeutic exercises may be feasible and provide potential benefits for rehabilitation of DKO.

• Proceedings of the Korea Institute of Convergence Signal Processing
• /
• 2001.06a
• /
• pp.25-28
• /
• 2001

A new decision-feedback equalization technique for a filter bank-based orthogonal frequency division multiplexing (OFDM) data transmission system operating in a frequency selective multipath fading channel is presented in this paper. At the cost of relatively increased computational complexity in comparison to the conventional OFDM systems, the proposed system achieves a better performance in terms of bit error rates. The simulation results confirm the superiority and robustness of our method, particularly, in the low SNR channel environment.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.25 no.1
• /
• pp.92-98
• /
• 2014

In this paper, the reconfigurable frequency selective surface for C-band was designed using patch array and grid structure. Frequency reconfigurability was obtained by varying the capacitance from varactor diode. From the optimized design parameters, we fabricated the reconfigurable frequency selective surface using the FPCB(Flexible Printed Circuit Board) and commercial varactor diode and measured the frequency reconfigurability for different bias voltage. From the measurement results, proposed structure has the wideband operating frequency of 6.6~7.6 GHz. We can applied this proposed structure to the smooth curved surface like as radome of aircraft or warship.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.21 no.4
• /
• pp.972-983
• /
• 1996

This paper proposes a new technique for frequency offset correction for OFDM systems on a frequency selective fading channel. Frequency offset in OFDM introduces interchannel interference among the multiple subcarriers of OFDM signal. To compensate the interference, this paper describes an algorithm with two stages:acquisition and tracking. At both stages, the proposed algorithm oversamples the received OFDM signal to obtain a couple of demodulated symbol sets. At acquisition stage the frequency offset is reduced to half or less of the intercarrier spacings by matching the sign pattern of each element of the sets. Next, at tracking stage the frequency offset is corrected with a frequency detector which is controlled by the correlation of the two sets. It is shown that the proposed algorithm can correct the frequency offset in the event of uncertainty in the initial offset that exceeds one half of the intercarrier spacing. In addition, the proposed algorithm is robust to transmitted symbols and channel characteristics by using oversampled symbol sets.