• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2002.04a
• /
• pp.14-16
• /
• 2002

Melting and re-solidification nature of $SmBa_2Cu_3O_{7-y}$ (Sm123) grains in Ba-Cu-O (Ba:Cu=3:5) liquid containing 0.7 at.% yttrium were investigated at the temperature lower than its melt point. When Sm123 grains/liquid powder compacts were heated to a temperature between two melting points of Ba-Cu-O liquid ($1000^{\circ}C$) and a Sm123 phase ($1060^{\circ}C$) and held at this temperature for appropriate time, Sm123 grains melted partly in the liquid that was formed by melting of the liquid-forming powder. During subsequent slow cooling, (Sm,Y)$Ba_2Cu_3O_{7-y}$ solidified at the outer parts of the unmelted Sm12 grains, which is distinguished from the core regions by lower $Sm_2BaCuO_5$ (211) density.

• Electrical & Electronic Materials
• /
• v.7 no.4
• /
• pp.331-340
• /
• 1994

Polysilicon on insulator has been recrystallized by zone melting recrystallization method with graphite strip heaters. Experiments are performed with non-seed SOI structures. When the capping layer thickness of Si$\_$3/N$\_$4//SiO$\_$2/ is 2.0.mu.m, grain boundaries are about 120.mu.m spacing and protrusions reduced. After the seed SOI films are annealed at 1100.deg. C in NH$\_$3/ ambient for 3 hours, the recrystallized silicon surface has convex shape. After ZMR process, the tensile stress is 2.49*10$\^$9/dyn/cm$\^$2/ and 3.74*10$\^$9/dyn/cm$\^$2/ in the seed edge and seed center regions. The phenomenon of convex shape and tensile stress difference are completely eliminated by using the PSG/SiO$\_$2/ capping layer. The characterization of SOI films are showed that the SOI films are improved in wetting properties. N channel SOI MOSFET has been fabricated to investigate the electrical characteristics of the recrystallized SOI films. In the 0.7.mu.m thickness SOI MOSFET, kink effects due to the floating substrate occur and the electron mobility was calculated from the measured g$\_$m/ characteristics, which is about 589cm$\^$2//V.s. The recrystallized SOI films are shown to be a good single crystal silicon.

• Horticultural Science & Technology
• /
• v.31 no.1
• /
• pp.80-88
• /
• 2013

Carrot (Daucus carota L. var. sativa) is one of the most extensively used vegetable crops in the world and a significant source of nutrient because of its high content of ${\beta}$-carotene, well known as the precursor of vitamin A carotenoid. However, seed-hairs generated and elongated from the epidermal cell of seeds inhibit absorption and germination by various factors such as carotol and so on. Accordingly, mechanical hair removal process is essential before commercialization of carrot seeds. Because of this process, producers will have additional losses such as time consuming, manpower, capital and so on. Furthermore, physical damage of seeds causes irregular germination rate. To overcome such cumbersome weaknesses, new breeding program for developing hairless-seed carrot cultivar has been needed and studies for molecular markers related to seed-hair characteristic is needed for a new breeding program. Therefore, in this study, cDNA libraries from seeds of short-hair seed phenotype CT-SMR 616 OP 659-1 line, hairy-seed phenotype CT-SMR 616 OP 677-14 line and short-hair seed phenotype CT-ATR 615 OP 666-13 line, hairy-seed phenotype CT-ATR 615 OP 671-9 were constructed, respectively. Furthermore, 1,248 ESTs in each line, total 4,992 ESTs were sequenced. As a result, 19 SNP sites and 14 SNP sites in each of 2 combinations were confirmed by analyzing these EST sequences from short-hair and hairy-seed lines. Then we designed SNP primer sets from EST sequences of SNP sites for high resolution melting (HRM) analysis. Designed HRM primers were analyzed using hairy seed phenotype CT-SMR 616 OP 1040 line and short-hair seed phenotype CT-SMR 616 OP 1024, 1025, 1026 lines. One set of HRM primers showed specific difference between the melting curves of hairy and short-hair seed phenotype lines. Based on this result, allele-specific (AS) PCR primers were designed for easier selection between hairy-seed carrot and hairless seed carrot. These results of HRM and AS-PCR are expected to be useful in breeding of hairless seed carrot cultivar as a molecular marker.

• Progress in Superconductivity and Cryogenics
• /
• v.24 no.3
• /
• pp.35-40
• /
• 2022

To fabricate large grain YBCO bulk superconductors by melt process, Sm123 single crystal with a high melting point are mostly used as seeds. However, it also uses Y123 film deposited on MgO single crystal substrate. This study investigated the growth behavior of the Y123 grain during a melt process when single grain YBCO bulk was used as a seed. Single grain Y123 bulk was grown when the seed size was small. When the seed size was relatively large, multiple grains were grown but the grains were still large. Y123 seed crystal was completely decomposed during high temperature anneal at 1040℃ and new Y123 crystals were nucleated during a slow cooling stage below a peritectic temperature. Thereafter, newly formed Y123 crystals from the seed area are thought to grow into the Y1.8 powder compact. The crystallographic orientations of newly nucleated Y123 grains are independent of the crystallographic orientation of Y123 seed. It is thought that the crystallographic orientation of newly nucleated Y123 crystal can be controlled by using Y211-free Y123 single crystal as a seed of homo-seeding melt growth.

• Resources Recycling
• /
• v.4 no.1
• /
• pp.25-30
• /
• 1995

In the preparatIon of reclaimed aluminium lllgot from alumimum scrap, the aluminium recovery was studied a as a function of the preliminary treatment of samples, addition of flux and melting atmosphere. AI dross is produced by an oxidation reaction at the surface of liquid metal. The recovery of AI metal increases u up to maximum 95% by adding salt up to 7%, The recovery of AI metal in the compacted chip bale without oil removal mcrease about 14% compared io non-compacted chip. In the case of the AI seed melting process, the recovery of Al metal of the crushed and compacted chip hale is 97%, In meltmg of alumimum scrap under the atmosphere of carbon and nitrogen gas, the recovery of AI metal increase, but it is decreased when the mixture of salt and carbon powder is added excessively.

• Proceedings of the Korean Society for Agricultural Machinery Conference
• /
• 1993.10a
• /
• pp.443-452
• /
• 1993

Direct freezing tests of soybean seed by liquid nitrogen were carried out at various moisture contents and the following important conclusions were drawn from the results of temperature measurements of soybean seed and photographs of bubbles generated on its surface : 1) Assuming that the temperature gradient in a soybean seed is negligible because of its small seed size and the freezing ratio is followed the Heiss's formula, and a differential equation based on the heat energy balance was introduced . The equation was easily solved by the Runge-Kutta-Gill method and the predicted values of the temperature were in good agreement with the observed data. 2) The photographs of bubble generation during freezing showed the boiling mode was nucleate, and then the most suitable formula on the nucleate boiling heat transfer was introduced from many formulate proposed up to now by fitting the calculated values based on the formula to the observed data. The formula used for the predict on of the seed temperature was as follows: $\frac{{\partial}T_s}{\partial\theta}\;=\;-\frac{{\alpha}(T_s\;-\;T_L)^{3.3}}{W(C_s\;-\;\frac{{\delta}m(CT_s\;+\;{\sigma})}{T_s^2})}$ where C = difference of the specific heat between pure ice and water m=moisture content of soybean seed $T_s$ = seed temperature $T_L$ = Temperature of liquid nitrogen W = mass of soybean seed $\alpha$ = proportional constant $\delta$ = constant depends on variety or the type of seed $\theta$ = time $\sigma$ = latent heat of melting of pure ice This study will give important information in the hydro-freezing technique by liquid nitrogen, available as a new technique of processing agricultural products in the near future.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.22 no.10
• /
• pp.860-863
• /
• 2009

YBCO bulks with fine $Y_2BaCuO_5$(Y211) particles have been prepared by the top-seed modified powder melting process method, Solid-Liquid Melt Growth(SLMG), with $Y_2O_3$, $BaCuO_2$ and CuO mixing precursor. By using $Y_2O_3$ instead of $Y_2BaCuO_5$ as precursor, the processing became to be simpler and cheaper than the current powder melting process. The microstructures, trapped field and critical current density of the various conditioned YBCO bulks have been analyzed and the effect of Pt additive was studied. The different trapped magnetic field values of the several samples have been explained in the viewpoint of their microstructures. The fabrication of large-sized YBCO single domain has been conducted.

• Journal of the Korean Society of Food Science and Nutrition
• /
• v.38 no.4
• /
• pp.470-478
• /
• 2009

Low trans fats were synthesized by interesterification of rice bran oil (RBO), palm stearin (PS) and high oleic sunflower seed oil (HO) using TLIM from Thermomyces lanuginosa. After 24-h reaction, physicochemical characteristics such as fatty acid and triacylglycerol composition, solid fat content, melting point, tocopherol, oryzanol and phytosterol contents were evaluated. Trans fatty acid contents of the produced low-trans fats showed less than 0.5 wt%. Mostly, triacylglycerol species in the products were palmitoyl-linoleoyl-oleoyl-glycerol (PLO), palmitoyl-oleoyl-oleoyl-glycerol (POO) and palmitoyl-oleoyl-palmitoyl-glycerol (POP). Total tocopherol contents ranged from 6.94 to 11.83 mg/100 g while $0.18{\sim}0.49$ mg/100 g of $\gamma$-oryzanol and $182.47{\sim}269.08$ mg/100 g of phytosterols were observed depending on the substrates ratios. When the content of PS in the reaction substrate was increased, solid fat content and slip melting points were increased.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2012.05a
• /
• pp.93.1-93.1
• /
• 2012

세라믹 고온초전도체는 에너지 저장장치의 핵심소재로 사용된다. 초전도 플라이휠 에너지 저장장치(Superconductor flywheel energy storage system)는 전기 에너지를 운동 에너지로 변환하여 저장하는 친환경, 고효율 에너지 저장장치이다. 에너지를 최소화하는데 사용되는 초전도 베어링은 고온초전도체와 영구자석으로 구성된다. 베어링에는 희토류계 초전도 물질(RE-Ba-Cu-O, RE:Rare-earth elements)가 사용된다. 베어링의 효율은 영구자석의 자력크기, 초전도체의 자기부상력과 포획자력에 비례한다. 에너지 저장효율을 높이려면 고온 초전도체의 임계전류밀도(초전도체 내부에 흘릴 수 있는 전기량)를 높이고, 초전도 결정립의 크기를 키워야 한다. 결정크기를 키우는 공정으로 종자결정성장법(Seed growth process)이 사용된다. 초전도체 제조공정은 분말의 성형, incongruent melting을 포함하는 부분 용융, 액상에서의 입성장, 포정반응을 통한 초전도 결정의 성장과정을 포함한다. 본 발표에서는 초전도 에너지 저장장치의 기본 원리, 초전도 베어링의 구성, 베어링용 초전도체의 제조방법과 특성(자기부상력과 포획자력) 평가기술, 차세대 에너지 저장장치로서의 초전도 플라이휠 에너지 저장장치의 전망에 대해 요약하였다.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2006.06a
• /
• pp.184-185
• /
• 2006

Two-step growth to incorporate the Mg atoms in the ZnO nanorods fabricate by thermal evaporation process and also utilized the ZnO film as a template. In the first step of low temperature, Zn seed metals with low melting temperature formed the droplet, and then MgZnO ternary nanorods were grown by injecting oxygen and evaporating Mg atoms in high temperature process of the second step. The vertical growth of the MgZnO nanorods with large-area distribution and uniformity was successfully performed on the ZnO template. We investigated the shape of the vertically grown 1-D MgZnO nanorods and characterized the optical and crystal properties. We confirmed the incorporation of Mg atoms by the EDS and PL spectrum.