• Earthquakes and Structures
• /
• v.4 no.2
• /
• pp.133-155
• /
• 2013

The earthquake responses are studied for the tall flexible structures such as TV towers when the vertical eccentricities between the discrete nodes and the corresponding centroids of investigated lumps are considered. In practical analyses, the tall flexible structures can be made into a spatial-discrete system of some certain length of beam elements with different lengths and cross-sectional areas. These elements are used to construct the investigated lumps in this paper. The different cross-sectional areas and the different lengths of two adjacent elements lead to the appearance of vertical eccentricity between the discrete node and the centroid of investigated lump within the same investigated lump. Firstly, the governing equations are established for a typical investigated lump. Secondly, the calculating formulae of the forces and moments acting on the investigated lump are derived and provided. Finally the new dynamic equilibrium equations with modified mass matrix and assemblage of stiffness matrix have been derived for the stick MDOF model based on beam theory when the existing vertical eccentricities are considered. Numerical results demonstrate that these vertical eccentricities should be considered in order to obtain the accurate earthquake responses for the tall flexible structures.

• Magazine of the Korean Society of Agricultural Engineers
• /
• v.31 no.4
• /
• pp.58-71
• /
• 1989

This study aims to develop a computerized program for analysis of the ground-supported cylindrical shell structure with step varied section and to find out its mechanical characteri- stics through application of the developed program to the analysis of a ensiled farm silo as a model structure. The thickness of wall and bottom-plate of farm silo is assumed to be step-varied and its detailed structural dimensions are presented in Tab. 1 and 2. Several numerical case studies show that sectional stresses of the sample structures are largely reduced by adopting "varied section" design technique. And, other major results ob- tained from this study are summarize4 as follows ; 1. The variation of wall-thickness has a great influence on bending stresses of wall. Ho- wever, the larger the relative thickness of bottom-plate is, the smaller the influence is. 2. The magnitude of thickness of projecting toe of bottom-plate has negligible effect on sectional stresses 3. The conventional design methodology, which assumes the bottom edge of wall as clam- ped on ground, is proved to be discarded through the numerical analysis. 4. It is found that the "varied section" design technique should get similar effects as in the case of thick bott6m-plate having uniform thickness. 5. The variation of wall-thickness has a considerable effect on the bending stresses of bo- ttom-plate. Especially, this phenomenon is very remarkable in its projecting toe. In some cases. the negative bending moment may be acted on.

• Proceedings of the KSME Conference
• /
• 2000.11b
• /
• pp.591-596
• /
• 2000

Flow through compliant tubes with linear taper in wall thickness is numerically simulated by finite element analysis. Two models are examined: a planar two-dimensional channel, and an axisymmetric tube. For verification of the numerical method, flow through a compliant stenotic vessel is simulated and compared to existing experimental data. Computational results for an axisymmetric tube show that as cross-sectional area falls with a reduction in downstream pressure, flow rate increases and reaches a maximum when the speed index (mean velocity divided by wave speed) is near unity at the point of minimum cross-section area, indicative of wave speed flow limitation or "choking" (flow speed equals wave speed) in previous one-dimensional studies. For further reductions in downstream pressure, flow rate decreases. Cross-sectional narrowing is significant but localized. When the ratio of downstream-to-upstream wall thickness is ${\le}$ 2 the area throat is located near the downstream end; as wall taper is increased to ${\ge}$ 3 the constriction moves to the upstream end of the tube. In the planar two-dimensional channel, area reduction and flow limitation are also observed when outlet pressure is decreased. In contrast to the axisymmetric case, however, the elastic wall in the two-dimensional channel forms a smooth concave surface with the area throat located near the mid-point of the elastic wall. Though flow rate reaches a maximum and then falls, the flow does not appear to be choked.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.19 no.6
• /
• pp.782-789
• /
• 2010

It is important to satisfy the requirements and standards for the protections of passengers in a car accident. There are lots of studies on the crushing energy absorption of a structure member in automobiles. In this paper, we have studied to investigate collapse characteristics and moisture absorption movements of CFRP( carbon fiber reinforced plastics) structure members when CFRP laminates are under the hygrothermal environment. In particular, the absorbed energy, mean collapse load and deformation mode were analyzed for CFRP members which absorbed most of the collision energy. Also, variation of stacking angle is important to increase the energy absorption capability. The purpose of this study is to evaluate the strength reduction and moisture absorption behavior of CFRP hat shaped member. Therefore we have made a impact collapse experiment to research into the difference of absorbed energy and deformation mode between moisture absorbed specimen and non-moisture absorbed. As a result, the effect of moisture absorption and impact loads of approximately 50% reduction in strength are shown.

• Korean Journal of Materials Research
• /
• v.13 no.2
• /
• pp.88-93
• /
• 2003

Co/Ti bilayer structure in Co salicide process helps to the improvement of device speed by lowering contact resistance due to the epitaxial growth of $CoSi_2$layers. We investigated the epitaxial growth and interfacial mass transport of $CoSi_2$layers formed from $150 \AA$-Co/Ti structure with two step rapid thermal annealing (RTA). The thicknesses of Ti layers were varied from 20 $\AA$ to 100 $\AA$. After we confirmed the appropriate deposition of Ti film even below $100\AA$-thick, we investigated the cross sectional microstructure, surface roughness, eptiaxial growth, and mass transportation of$ CoSi_2$films formed from various Ti thickness with a cross sectional transmission electron microscopy XTEM), scanning probe microscopy (SPM), X-ray diffractometery (XRD), and Auger electron depth profiling, respectively. We found that all Ti interlayer led to$ CoSi_2$epitaxial growth, while $20 \AA$-thick Ti caused imperfect epitaxy. Ti interlayer also caused Co-Ti-Si compounds on top of $CoSi_2$, which were very hard to remove selectively. Our result implied that we need to employ appropriate Ti thickness to enhance the epitaxial growth as well as to lessen Co-Ti-Si compound formation.

• Steel and Composite Structures
• /
• v.8 no.5
• /
• pp.343-359
• /
• 2008

In the present study, an efficient method for the optimum design of three-dimensional (3D) steel framed structures is proposed. In this method, in addition to choosing the best position of columns based on architectural requirements, the optimum cross-sectional dimensions of elements are determined. The preliminary design variables are considered as the number of columns in structural plan, which are determined by a direct optimization method suitable for discrete variables, without requiring the evaluation of derivatives. After forming the geometry of structure, the main variables of the cross-sectional dimensions are evaluated, which satisfy the design constraints and also achieve the least-weight of the structure. To reduce the number of finite element analyses and the overall computational time, a new third order approximate function is introduced which employs only the diagonal elements of the higher order derivatives matrices. This function produces a high quality approximation and also, a robust optimization process. The main feature of the proposed techniques that the higher order derivatives are established by the first order exact derivatives. Several examples are solved and efficiency of the new approximation method and also, the proposed method for the best position of columns in 3D steel framed structures is discussed.

• Ecology and Resilient Infrastructure
• /
• v.7 no.4
• /
• pp.320-326
• /
• 2020

The present study aimed to assess the longitudinal connectivity owing to migrant characteristics of the target fish. The study area was Wonju-cheon Stream, and the target species were Zacco platypus and Minnows. The HEC-RAS model was used for the computation of the flow, and the ICE (Information sur la Continuite Ecologique) method was used to analyze the longitudinal connectivity. The longitudinal connectivity was assessed using the minimum overflow height, velocity, and depth of the cross sectional structure of a plunge pool and considering the swimming speed of the target fish. Simulation results indicated that the longitudinal connectivity scores for the Zacco platypus and Minnows were approximately 76 and 23, respectively.

• Journal of Power System Engineering
• /
• v.7 no.4
• /
• pp.38-43
• /
• 2003

This paper proposes an optimum design problem of structural and control systems. taking a 3-D truss structure as an example. The structure is supposed to be subjected to initial static loads and time-varying disturbances. The structure is controlled by a state feedback $H_{\infty}$ controller to suppress the effect of the disturbances. The design variables are the cross sectional areas of truss members. The structural objective function is the structural weight. As the control objective, we consider two types of performance indices. The first function represents the effect of the initial loads. The second one is the norm of the feedback gain. These objective functions are in conflict with each other. Then, first, two control objective functions are transformed into one control objective by the weighting method. Next, the structural objective is treated as the constraint. By introducing the second control objective which considers the magnitude of the feedback gain, we can per limn the design which is robust in modeling errors.

• Transactions of Materials Processing
• /
• v.15 no.2 s.83
• /
• pp.126-131
• /
• 2006

Metallic sandwich plates are ultra-light materials not only with high strength and stiffness but also with other multifunctional physical properties. Inner dimpled shell structure can be fabricated by a piecewise sectional forming process, and then bonded with face sheets of the same material by resistance welding. Possible region for bending and limit radius of curvature are defined to compare the formability of sandwich plates. Tests have shown that sandwich plates with inner dimpled shell structure subject to bending have longer possible region for bending and smaller limit radius of curvature than other types of sandwich plates. The proposed inner dimpled shell structure is shown to have better formability of sandwich plates for bending than other types inner structures.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2005.10a
• /
• pp.301-304
• /
• 2005

Metallic sandwich plates are ultra-light materials with not only high strength and stiffness but also multifunctional. Inner dimpled shell structure can be fabricated by piecewise sectional forming process, and then bonded with same material face sheets by resistance welding. Tests have shown that sandwich plates with dimpled shell structure subject to bending have more collapse load, energy absorption and deflection before collapse than other types of sandwich plates. Consequently, inner dimpled shell structure can improve formability of sandwich plates for bending.