• Journal of the Korean Society of Clothing and Textiles
• /
• v.34 no.11
• /
• pp.1889-1899
• /
• 2010

This study examines the preparation and characterization of Kenaf/Starch bio-composites used as filler and a matrix. Kenaf was cultivated in Chung-ju in Korea, and the Kenaf/Starch bio-composites were prepared under various conditions of kenaf fiber length (1-5 centimeters); the content of Kenaf fiber was 10%, 20%, 30%, and 40%, and the number of composite layers (one-four). Depending on the formation conditions of Kenaf/Starch composites, the physical properties such as tensile strength, elongation, and the young modulus of the Kenaf/Starch composites were measured. In addition, we measured the SEM cross-section images in order to investigate the interfacial adhesion properties of fractured surfaces. As a result, the tensile strength and elongation of the Kenaf/Starch composites were highest in the molding conditions of a hot press at $120^{\circ}C$, 3000PSI of pressure, and for 30 minute periods. The result of measuring the physical properties of the composites manufactured by varying the content of Kenaf fiber when the content of Kenaf fiber was 30% as well the physical properties of the Kenaf/Starch composite was found desirable. It was found that the physical properties improved with more overlapped layers in the composites manufactured by varying the number of overlapped layers. Through the measuring of the SEM cross-section images, we found that the interfacial adhesion state between the filler and matrix of Kenaf/Starch composite greatly affects the physical properties.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2008.11a
• /
• pp.217-220
• /
• 2008

A modified FRP-concrete composite deck applicable to cable stayed bridge with long girder-to-girder span is proposed, and its design and economical efficiency are presented. The existing FRP-concrete composite deck has low section stiffness due to adoption of GFRP panel with low elastic modulus, which arrives at difficulty in meet of serviceability limit such as deck deflection. So a new-type FRP-concrete composite deck, named precast FRP-concrete deck, is developed by extensioning concrete at the both ends of FRP-concrete composite deck, which brings the effect of reduction of net span length of deck. Compared to the existing FRP-concrete composite deck this modified deck has the advantage of increasing span length but slightly increases self weight. For this type of deck the section optimization is carried out for the cases of simply supported on girder and composite to girder. The optimized deck was applied to cable stayed bridge with a center span length of 540m, and as a result it is verified that PFC deck can be applied efficiently to cable stayed bridge due to reduction of quantity of upper structure.

• Journal of the Korea Concrete Institute
• /
• v.18 no.3 s.93
• /
• pp.425-429
• /
• 2006

Horizontal cracks at the mid-depth of concrete slabs were observed at a section of the continuously reinforced concrete pavement(CRCP) structures on the Korea Highway Corporation's Test Road. To investigate the existence and the extent of horizontal cracks in the concrete slab, a number of cores were taken from the section of CRCP. To identify the causes of horizontal cracks, numerical analyses were conducted. Several variables relative to design, material, and environment were considered in the studies to evaluate possible causes of horizontal cracking. A numerical model of CRCP was developed using the finite element discretization, and the shear and normal tensile stress distributions in CRCP were investigated with the model. Numerical analysis results show that the maximum shear and normal tensile stresses develop near the depth of steel bars at transverse cracks. If those maximum stresses reach the strength of concrete, horizontal cracks occur. The maximum stresses become higher as the environmental loads, coefficient of thermal expansion of concrete, and elastic modulus of concrete increase.

• Journal of the Korean Society for Advanced Composite Structures
• /
• v.2 no.1
• /
• pp.15-22
• /
• 2011

Pultruded fiber reinforced polymeric plastic (PFRP) structural members may be one of attractive alternatives of the structural members in the civil engineering applications because of its many advantageous mechanical properties. However, they have relatively low modulus of elasticity and also cross-sections of structural shapes are composed of thin plate components such as flange and web. Therefore, structural stability is an important issue in the design of pultruded structural compression members. For the design of pultruded structural member under compression, buckling and post-buckling strengths of plate components may be taken into account. In the structural steel design following AISC/LRFD, in addition to the buckling strength, the nonuniform stress distribution in the section is incorporated with a form factor. In this paper, the form factor for the design of PFRP structural member under compression is investigated through the analytical study. Furthermore, the process for the determination of the form factor is suggested.

• Structural Engineering and Mechanics
• /
• v.54 no.6
• /
• pp.1135-1152
• /
• 2015

Most of current bridge decks are made of reinforced concrete and often deteriorate at a relatively rapid rate in operational environments. The quick deterioration of the deck often impacts other critical components of the bridge. Another disadvantage of the concrete deck is its high weight in long-span bridges. Therefore, it is essential to examine new materials and innovative designs using hybrid system consisting conventional materials such as concrete and steel with FRP plates which is also known as composite deck. Since these decks are relatively new, so it would be useful to evaluate their performances in more details. The present study is dedicated to Hat-Shape composite girder with concrete slab. The structural performance of girder was evaluated with nonlinear finite element method by using ABAQUS and numerical results have been compared with experimental results of other researches. After ensuring the validity of numerical modeling of composite deck, parametric studies have been conducted; such as investigating the effects of constituent properties by changing the compressive strength of concrete slab and Elasticity modulus of GFRP materials. The efficacy of the GFRP box girders has been studied by changing GFRP material to steel and aluminum. In addition, the effect of Cross-Sectional Configuration has been evaluated. It was found that the behavior of this type of composite girders can be studied with numerical methods without carrying out costly experiments. The material properties can be modified to improve ultimate load capacity of the composite girder. strength-to-weight ratio of the girder increased by changing the GFRP material to aluminum and ultimate load capacity enhanced by deformation of composite girder cross-section.

• Journal of the Korean GEO-environmental Society
• /
• v.11 no.11
• /
• pp.5-18
• /
• 2010

In this paper, a 3-dimensional stiffened plate model for soil-metal box structures is proposed. 3-dimensional stiffened plate model is enable to model corrugated steel plates of soil metal box culverts considering section modulus and section properties of longitudinal and horizontal direction from a corrugated steel plate. Loading conditions which causes maximum displacement and maximum moment according to the step construction stages(a back filling to the top of the plate, a back filling to the maximum depth of cover, and loading of live loads) was applied and the behaviors of the soil metal box culverts was analyzed. Analysis results of 3-dimensional stiffened model were compared with those of 2-dimensional model, 3-dimensional equivalent plate model and 3-dimensional corrugated plate model. As results, the behaviors of 2-dimensional model and 3 dimensional equivalent model are different from 3-dimensional corrugated plate model but the result of 3-dimensional stiffened model has good agreement with that of 3-dimensional corrugated plate model.

• International journal of steel structures
• /
• v.18 no.4
• /
• pp.1440-1463
• /
• 2018

The Wagner coefficient is a key parameter used to describe the inelastic lateral-torsional buckling (LTB) behaviour of the I-beam, since even for a doubly-symmetric I-section with residual stress, it becomes a monosymmetric I-section due to the characteristics of the non-symmetrical distribution of plastic regions. However, so far no theoretical derivation on the energy equation and Wagner's coefficient have been presented due to the limitation of Vlasov's buckling theory. In order to simplify the nonlinear analysis and calculation, this paper presents a simplified mechanical model and an analytical solution for doubly-symmetric I-beams under pure bending, in which residual stresses and yielding are taken into account. According to the plate-beam theory proposed by the lead author, the energy equation for the inelastic LTB of an I-beam is derived in detail, using only the Euler-Bernoulli beam model and the Kirchhoff-plate model. In this derivation, the concept of the instantaneous shear centre is used and its position can be determined naturally by the condition that the coefficient of the cross-term in the strain energy should be zero; formulae for both the critical moment and the corresponding critical beam length are proposed based upon the analytical buckling equation. An analytical formula of the Wagner coefficient is obtained and the validity of Wagner hypothesis is reconfirmed. Finally, the accuracy of the analytical solution is verified by a FEM solution based upon a bi-modulus model of I-beams. It is found that the critical moments given by the analytical solution almost is identical to those given by Trahair's formulae, and hence the analytical solution can be used as a benchmark to verify the results obtained by other numerical algorithms for inelastic LTB behaviour.

• Journal of the Korean Wood Science and Technology
• /
• v.30 no.2
• /
• pp.95-101
• /
• 2002

Physical and mechanical properties of major Korean ash species were examined. For Fraxinus rhynchophylla and Fraxinus sieboldiana, green moisture content of sapwood was almost the same value as heartwood. Heartwood of Fraxinus mandshurica, however, had slightly higher moisture content than sapwood. Green and oven dry densities of F. mandshurica were lower than those of F. rhynchophylla and F. sieboldiana. Swelling and shrinkage of sapwood in F. sieboldiana showed somewhat higher value than those of F. rhynchophylla. Longitudinal compressive strength and modulus of elasticity in F. sieboldiana were lower values than those in the other species. Shearing strength in radial section was higher than that in tangential section of all samples. It could be noted that shearing strength of F. sieboldiana demonstrated higher value than that of the other species. Three species had excellent bending properties in MOR and MOE. Impact bending absorbed energy for F. rhynchophylla and F. mandshurica did not show any significant differences.

• Steel and Composite Structures
• /
• v.47 no.2
• /
• pp.269-287
• /
• 2023

The WGJ420 fire-resistant weathering (FRW) steel is developed and manufactured with standard yield strength of 420 MPa at room temperature, which is expected to significantly enhance the performance of steel structures with excellent fire and corrosion resistances, strong seismic capacity, high strength and ductility, good resilience and robustness. In this paper, the mechanical properties of FRW steel plates and buckling behavior of columns are investigated through tests at elevated temperatures. The stress-strain curves, mechanical properties of FRW steel such as modulus of elasticity, proof strength, tensile strength, as well as corresponding reduction factors are obtained and discussed. The recommended constitutive model based on the Ramberg-Osgood relationship, as well as the relevant formulas for mechanical properties are proposed, which provide fundamental mechanical parameters and references. A total of 12 FRW steel welded I-section columns with different slenderness ratios and buckling load ratios are tested under standard fire to understand the global buckling behavior in-depth. The influences of boundary conditions on the buckling failure modes as well as the critical temperatures are also investigated. In addition, the temperature distributions at different sections/locations of the columns are obtained. It is found that the buckling deformation curve can be divided into four stages: initial expansion stage, stable stage, compression stage and failure stage. The fire test results concluded that the residual buckling capacities of FRW steel columns are substantially higher than the conventional steel columns at elevated temperatures. Furthermore, the numerical results show good agreement with the fire test results in terms of the critical temperature and maximum axial elongation. Finally, the critical temperatures between the numerical results and various code/standard curves (GB 51249, Eurocode 3, AS 4100, BS 5950 and AISC) are compared and verified both in the buckling resistance domain and in the temperature domain. It is demonstrated that the FRW steel columns have sufficient safety redundancy for fire resistance when they are designed according to current codes or standards.

• Proceedings of the Korean Society of Crop Science Conference
• /
• 2017.06a
• /
• pp.133-133
• /
• 2017

Lodging is one of the important constraints in rice production. The lodging destroys the canopy structure, and sharply reduces the capacity of photosynthetic rate and dry matter production. In cereal crops, stem lodging can be classified into two types: stem breaking type and stem bending type. To improve stem lodging resistance, it is important to reveal strong culm traits of superior lodging resistant varieties. There are large varietal differences in parameters associated with the bending moment at breaking (M) and flexural rigidity (FR). The indica variety Takanari possesses large M due to its large section modulus (SM) despite of its small bending stress (BS), while Takanari also has large FR due to its large secondary moment of inertia (SMI) and Young's modulus (YM). To identify quantitative trait loci (QTLs) and the corresponding genes associated with the parameters for M ($=SM{\times}BS$) and FR ($=SM{\times}YM$) should enable to develop lodging resistant varieties, efficiently. In order to identify QTLs for cell wall materials such as cellulose, hemicellulose and lignin associated with BS and YM, a set of Chromosome Segment of Substitution Lines (CSSLs) consisted of 37 lines with chromosome segments of Koshihikari in the genetic background of Takanari were used. Takanari had large M and small BS as compared with Koshihikari. The QTLs for BS were estimated on chromosomes 3, 5, 6, 8, 9, 10, 11 and 12. Koshihikari alleles increased BS in these QTLs. Takanari had a large FR due to its large SMI and YM as compared with Koshihikari. The YM was increased by substitution of the Koshihikari chromosomal segments on chromosomes 2, 10 and 11. Other QTLs estimated on chromosomes 7 and 12 that Koshihikari alleles contributed to the decrease of YM. For lignin, only one major QTL for lignin density was detected on chromosome 11. Hollocellulose densities were increased by the substitution of Koshihikari segments on chromosomes 5 and 11. On the other hand, these were decreased on chromosomes 1 and 3 by substitution of Koshihikari segments. QTLs for cellulose density were estimated on chromosomes 1, 3 and 5 by substitution of Koshihikari segments. For hemicellulose, QTL on chromosome 3 showed that hemicellulose density decreased by the substitution of Koshihikari segment. However, hemicellulose densities on chromosomes 5, 8 and 11 showed the opposite effects. The QTLs for hemicellulose, cellulose, and hollocelulose densities identified on chromosome 5 overlapped with that for bending stress, indicating the positive effect of Koshihikari segment on increasing bending stress. These results suggest that some QTLs for the densities of cell wall materials contribute to increasing bending stress and Young's modulus, and could be utilized to improve the lodging resistance for both types of breaking and bending in rice varieties.