• Current Photovoltaic Research
• /
• v.4 no.4
• /
• pp.155-158
• /
• 2016

Long-term stability of dye-sensitized solar cell (DSSC) module is critical for the commercialization. We investigated the effect of sealing technology on the long-term stability of the $10cm{\times}11cm$ sized DSSC modules. We applied the concept of secondary sealing to the module and then performed several stability tests such as humidity cycle, 1 sun light soaking and outdoor stability tests. The enhanced stability was confirmed for the DSSC module employing optimized sealing materials and architectures.

• Tribology and Lubricants
• /
• v.22 no.1
• /
• pp.20-25
• /
• 2006

The stress behavior analysis of a-rings and packing for a LPG filling unit has been presented using a finite element analysis technique by non-linear MSC/MARC program. The sealing performance and endurance of a-rings and packing are affected by working conditions such as filling pressure, friction coefficient, compression ratio, and material properties. The elastomeric polymers of O-rings and packing are nitrile butadiene rubber (NBR) and polytetrafluoroethylene (PTFE), which are selected as proper materials of a-rings and packing based on the stress analysis results. The calculated FEM results showed that the proper material of O-ring is NBR as a secondary sealing component and the recommended material of packing is PTFE as a primary sealing unit during a LPG filling process.

• Journal of the Semiconductor & Display Technology
• /
• v.12 no.2
• /
• pp.45-50
• /
• 2013

This paper focuses on the fundamental issues for improving the efficiency and throughput of the AC PDP (Plasma Display Panel) manufacturing. The properties of the MgO protective layer affect the PDP efficiency. Especially, the secondary electron emission efficiency was affected on the deposition rate of MgO during the evaporation. In this study, the deposition rate of 5 $\AA$/s has given the maximum efficiency value of 0.05 It is demonstrated that the impurity gases such as $H_2O$, $CO_2$, CO or $N_2$, and $O_2$ can be remained inside the PDP panel before sealing and the amount of the impurity gases decreased rapidly as the base vacuum level increased, especially near $10^{-5}$ torr. The fundamental solution in order to overcome these problems is the vacuum in-line sealing process from the MgO evaporation to the final sealing of the panel without breaking the vacuum. We have demonstrated this fundamental process technology and shown the feasibility. The firing voltage was reduced down to 285 V at the base vacuum value of $10^{-6}$ torr, whreras it was about 328 V at the base vacuum value of $10^{-3}$ torr.

• Journal of the Korean Institute of Gas
• /
• v.9 no.1 s.26
• /
• pp.26-32
• /
• 2005

This paper presents the design safety of metal seals in pressure vessels. For a high-pressure vessel, a metal seal is usually used as a primary sealing, and an elastomeric rubber O-ring is adopted as a secondary sealing unit. The FEM computed results show that an aluminium material for sealing a gas leakage is superior to a steel one because of the thermal expansion rate. The deformation and stress distributions on the metal seal and pressure vessel structures are mainly dominated by transferred temperature compared to those of the gas pressure in which is supplied by an external pump. Thus, the temperature of a metal seal material should be restricted to under $200^{\circ}C$.

• Proceedings of the KIEE Conference
• /
• 1998.11a
• /
• pp.10-12
• /
• 1998

Pumping liquid metal in nuclear power plant application by conventional centrifugal pumps pose difficulties such as bearing wear out at high temperatures and leak proof sealing of the liquid metal. MHD machine is obtained by replacing solid conducting secondary of conventional motors with ionized gas or liquid metal. It is used for reactor cooling pump because of construction simplicity, perfect sealing and easy operation/maintenance MHD pump is complicated because it includes electromagnetic and hydrodynamic phenomena. The principle of MHD Pumps is described in this paper. We design small laboratory size Flat Linear Induction Pump(FLIP) for transferring sodium.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.26 no.1
• /
• pp.38-46
• /
• 2022

One of the main goal of gas turbine rim seal research is to prevent thermal damage at rotor-stator disk by preventing hot gas of main flow in turbine passage. To increase sealing performance, several studies related to the improvement of rim seal configuration have been conducted. In addition, research based on actual operating condition is needed in order to apply effective turbine rim seal configuration. In this study, numerical simulation was conducted with variation of rotor rim seal thickness. Radial and axial expansion cases were tested numerically in this study. As a result, the cases showed different pressure distribution, sealing performance and flow characteristics according to the amount of secondary flow.

• 유체기계공업학회:학술대회논문집
• /
• 2000.12a
• /
• pp.158-162
• /
• 2000

Secondary flows in gas turbines, especially those associated tip clearance and labyrinth seals, have become a focus of interest for engine manufacturers. In the past, many analytical and experimental studies, which focused solely on the flows in either tip clearances or seals, have been conducted. This paper presents an analytical model that describes the flow response in a single stage turbine induced by a finite sealing gap at the turbine rotor. The flow is assumed to be axisymmetric and the analysis is done in the meridional plane. Upon going through the stage, the radially uniform upstream flow is assumed to split into two streams one associated with the seal and the other which has gone through the blades. The former is referred to as the leakage flow, and the latter is referred the as the passage flow. The passage flow is assumed to be inviscid and incompressible while the flow in the seal can be modeled as either inviscid or viscous. Thus, the model is capable of predicting the kinematic effects of labyrinth seals on the turbine flow field.

• Proceedings of the KIEE Conference
• /
• 2005.07b
• /
• pp.1059-1061
• /
• 2005

The bushing currently applied to pole-mounted type loadbreak switch has porcelain bushing which is connected with the mold cone. This type has potential problems of uncertainty of sealing of the interface part and gas leakage on the connected part between bushing and switch tank due to the weight of the porcelain. The Composite Bushing can solve these problems and also the secondary problem of the potential accident owing to the fragment of the porcelain bushing in breakage due to the outer impact.

• Transactions of the Korean Society of Pressure Vessels and Piping
• /
• v.16 no.1
• /
• pp.11-21
• /
• 2020

This study aims to develop and advance the evaluation technology for assessing PHWR safety. For this purpose, the complete loss of AC power or station blackout (SBO) was selected as a target accident scenario and the analysis model to evaluate the plant responses was envisioned into the MARS-KS input model. The model includes the main features of the primary heat transport system with a simplified model for the horizontal fuel channels, the secondary heat transport system including the shell side of steam generators, feedwater and main steam line, and moderator system. A steady state condition was achieved successfully by running the present model to check out the stable convergence of the key parameters. Subsequently, through the SBO transient analyses two cases with and without the coolant leakage via the PHTS pumps were simulated and the behaviors of the major parameters were compared. The sensitivity analysis on the amount of the coolant leakage by varying its flow area was also performed to investigate the effect on the system responses. It is expected that the results of the present study will contribute to upgrading the evaluation technology of the detailed thermal hydraulic analysis on the SBO transient of the operating PHWRs.

• Journal of Korean society of Dental Hygiene
• /
• v.16 no.1
• /
• pp.45-52
• /
• 2016

Objectives: The purpose of the study was to investigate the cumulative dental caries rate of pit and fissure sealant in community public health program from 2005 to 2008 follow-up. Methods: The subjects were 4,768 students of 34 elementary schools in Gimcheon. The survey included direct oral examination and cumulative retention rate of pit and fissure sealant from 2005 to 2008. Data were analyzed using PASW statistical package version 18.0 and the level of significance was set at p<0.05. Results: The cumulative retention rate of sealant was 18%, 25%, and 33% after 1 year, 2 years, and 3 years, respectively. In addition, the cumulative retention rate of lower teeth was higher than that of upper teeth. Cumulative dental caries rate increased in sealed group and no sealed group. The cumulative dental caries rate decreased owing to tooth brushing frequency in sealed group and no sealed group. Conclusions: Regular and timely tooth brushing can maintain good oral health condition after tooth sealing. The school based oral health education can prevent loss of sealant and secondary caries.