• 대한기계학회논문집B
• /
• 제21권1호
• /
• pp.165-173
• /
• 1997

The present study investigates heat/mass transfer for flow through perforated plates for application to combustor wall and turbine blade film cooling. The experiments are conducted for hole length to diameter ratios of 0.68 to 1.5, for hole pitch-to-diameter ratios of 1.5 and 3.0, for gap distance between two parallel perforated plates of 1 to 3 hole diameters, and for Reynolds numbers of 60 to 13, 700. Local heat/mass transfer coefficients near and inside the cooling holes are obtained using a naphthalene sublimation technique. Detailed knowledge of the local transfer coefficients is essential to analyze thermal stress in turbine components. The results indicate that the heat/mass transfer coefficients inside the hole surface vary significantly due to flow separation and reattachment. The transfer coefficient near the reattachment point is about four and half times that for a fully developed circular tube flow. The heat/mass transfer coefficient on the leeward surface has the same order as that on the windward surface because of a strong recirculation flow between neighboring jets from the array of holes. For flow through two perforated plate layers, the transfer coefficients on the target surface (windward surface of the second wall) affected by the gap spacing are approximately three to four times higher than that with a single layer.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2004년도 추계학술대회 논문집
• /
• pp.127-130
• /
• 2004

For the quality control of the industrial products, an automatic hole measuring system has been developed. The measurement device allows X-Y movement due to contact forces between a hole and its own circular cone and the device is attached to an industrial robot. Its measurement accuracy is about 0.04mm. This movement of the plate is measured by two LVDT sensor system. But this system using the LVDT sensors is restricted by high cost and precision of measurement and correspondence of environment so particularly, a vision system with CCD-Camera is discussed in this paper for the above mentioned purpose. The device consists of two of two links jointed with hinge pins basically and, they guarantee free movement of the touch prove attached on the second link in the same plane. These links are returned to home position by the spring plungers automatically after each process for the next one. On the surface of the touch prove, it has a circular white mark for camera recognition. The system detect and notify the center coordinate of capture mark image through the image processing. Its measuring accuracy has been proved to be about $\pm$0.01mm through the repeated implementation over 200 times. This technique will shows the advantage of touch-indirect image capture idea using cone-shaped touch prove in various symmetrical shaped holes particulary, like tapped holes, chamfered holes, etc As a result, we attained our object in a view of the accuracy, economical efficiency, and functionality

• 대한핵의학회지
• /
• 제19권1호
• /
• pp.73-75
• /
• 1985

Acute transient synovitis of the hip presents clinically pain and limping. But in the majority of the cases, definite positive findings are not manifest in roentgenogram in its early phase. However radionuclide bone imaging combines with the assessment of vascularization and bone tracer uptake is of great value in solving this diagnostic problem. The materials for this study consisted of 29 children with acute transient synovitis of the hip, characterized by symptoms and physical signs of an arthritis, negative X-ray findings and disappearance of all symptoms and signs within a short period of time. They were twenty males and 9 females and age ranged from 1 to 12 years. We took pelvic reontgenogram in AP and frog-leg views. After intravenous bolus injection of 10 to 15 mCi of $^{99m}Tc-methylene$ diphosphonate, 24 sequential image of the pelvis was taken at 2-second interval for blood flow study. The scintigrams were made using a gamma camera with high resolution parallel hole collimator. Blood pool imaging was obtained at 2 minutes after tracer administration. After 3 hours, static images were taken and then closeup image of the hip using pin-hole collimator was followed. The results were as follows: 1) Bone scintigram was much more sensitive than conventional roentgenogram in diagnosis of acute transient synovitis of the hip. 2) Three-phase imagings showed increased vascular activities in blood pool scintigrams in 96%. 3) Pin-hole imaging showed increased tracer uptake in the regional bones of the hip, par ticularly in the medial aspect of femoral head and acetabulum. 4) We confirmed that three-phase imaging reinforced with pin-hole technique were very useful in diagnose of acute transient synovitis of the hip.

• 한국전산구조공학회논문집
• /
• 제16권1호
• /
• pp.105-111
• /
• 2003

승용차의 휠은 타이어와 차체 무게를 지지하며, 회전력과 정지력을 노면으로 전달한다. 휠의 경량화는 차량의 연료효율에 효과적이므로, 스틸휠이 무게를 최소화하도록 디스크 홀이 형상을 최적화 하였다. 설계모델은 Pro/ENGINEER를 사용하여 설정하고, 설계모델의 해석은 ANSYS를 이용하였다. 범용 소프트웨어간의 직접적인 자료의 전달이 어려우므로 두 프로그램을 병합 사용하기 위해, 반응표면법을 이용한 근사함수를 구하였다. 5수준의 요인배치법의 실험값을 사용하여 최대응력과 최대 변위를 추출하였다. 초기 모델은 14인치 승용차용 스틸휠을 사용하였고, 디스크 홀의 폭을 설계변수로 선택하였다. 순차이차계획법과 활성화제약조건을 사용하는 PLBA(Pahenichny-Lim-Belegundu-Arora) 알고르즘을 이용하여 최적해를 구하였다.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2013년도 제45회 하계 정기학술대회 초록집
• /
• pp.244.1-244.1
• /
• 2013

The p-type GaN which act as a hole injection layer in GaN-based LEDs has fundamental problems. The first one arises from the difficulty in growing a highly doped p-GaN (with a carrier concentration exceeding ~1018 $cm^{-3}$). And the second one is the absence of appropriate metals or conducting oxides having a work function that is larger than that of p-type GaN (7.5 eV). Moreover, the LED efficiency is decreases gradually as the injection current increases (the so-called 'efficiency droop' phenomenon). The efficiency droop phenomenon in InGaN quantum wells (QWs) has been a large obstacle that has hindered high-efficiency operation at high current density. In this study, we introduce the new approaches to improve the light-output power of LEDs by using graphene oxide sheets. Graphene oxide has many functional groups such as the oxygen epoxide, the hydroxyl, and the carboxyl groups. Due to nature of such functional groups, graphene oxide possess a lot of hole carriers. If graphene oxide combine with LED top surface, graphene oxide may supply hole carriers to p-type GaN layer which has relatively low free carrier concentration less than electron concentration in n-type GaN layer. To prove the enhancement factor of graphene oxide coated LEDs, we have investigated electrical and optical properties by using ultra-violet photo-excited spectroscopy, confocal scanning electroluminescence microscopy.

• Computers and Concrete
• /
• 제32권1호
• /
• pp.99-117
• /
• 2023

The crack under the influence of the higher intensities of the stresses grows and the structure gets collapsed with the time when the crack length reaches to critical value. Therefore, the fracture behavior of a structure in terms of stress intensity factors (SIF) becomes important to determine the remaining fracture strength and capacity of material and structure for avoiding catastrophic failure, increasing safety and further improvement in the design. The robustness of the method has been demonstrated by comparing the numerical results with analytical and experimental results of some problems. XFEM is used to model cracks and holes in structures and predict their strength and reliability under service conditions. Further, XFEM is extended with a stochastic method for predicting the sensitivity in terms of output COVs and fracture strength in terms of mean values of stress intensity factors (SIFs) of a structure with discontinuities (cracks and holes) under tensile loading condition with input individual and combined randomness in different system parameters. In stochastic technique, the second order perturbation technique (SOPT) has been used for the predicting the fracture behavior of the structures. The stochastic/perturbation technique is also known as Taylor series expansion method and it provides the reliable results if the input randomness is less than twenty percentage. From the present numerical analysis it is observed that, the crack tip near to the hole is under the influence of the stress concentration and the variational effect of the input random parameters on the crack tip in terms of the SIFs are lesser so the COVs are the less sensitive. The COVs of mixed mode SIFs are the most sensitive for the crack angles (α=45° to 90°) for all the values of c₁ and d₁. The plate with the shorter distance between hole and crack is the most sensitive with all the crack angles but the crack tip which is much nearer to the hole has the highest sensitivity.

• 한국정밀공학회지
• /
• 제18권10호
• /
• pp.200-207
• /
• 2001

Burrs farmed in drilling are classified into three types, no burr, burrs with cap, teared burr. To control burr size in drilling, the second type burrs with cap are to be formed because it is small and uniform. It is necessary to understand the mechanism of cap formation to derive the burr formation into second type burr with cap. In several materials. second type burrs are formed in drilling by changing cutting conditions. It is observed that cap is formed as a result of the plastic deformation along the outside of exit hope. According to the tension behavior of the material in concentrated region between hole and drill outside edge, the geometry of burr with cap is determined. Simplified 2D FEM analysis shows good prediction for burr formation.

• 한국음향학회지
• /
• 제1권1호
• /
• pp.92-96
• /
• 1982

In this paper, the interaction of electron and phonon in metals is expressed using Hamiltonian operator as follows. By excahnging phonon energy with in the vicinity of isotropical Fermi surface and using following electron and hole operators. We obtain the interaction of electron and phonon. And new Feynman Graphs are tried with the following conditions on. First, when state transfer state, phonon cannot be created. Second, when state transfer state, phonon cannot be destroyed. Third, when state transfer state, phonon can be created or destroyed. Fourth, when state transfer state, phonon can be created or destroyed.

• Asia pacific journal of information systems
• /
• 제20권4호
• /
• pp.101-123
• /
• 2010

Recently, firms are operating a number of teams to accomplish organizational performance. Especially, ad hoc teams like proposal preparation team are quite different from permanent teams like R&D team in the sense of how the team forms network structure and deals with organizational learning culture and knowledge management participation efforts. Moreover, depending on the team characteristics, individual creativity will differ from each other, which will lead to organizational performance eventually. Previous studies in the field of creativity are lacking in this issue. So main objectives of this study are organized as follows. First, the issue of how to improve individual creativity and organizational performance will be analyzed empirically. This issue will be performed depending on team characteristics such as ad hoc team and permanent team. Antecedents adopted for this research objective are cultural and knowledge factors such as organizational learning culture, and knowledge management participation. Second, the network structure such as degree centrality, and structural hole is used to analyze its influence on individual creativity and organizational performance. SI (System Integration) companies are facing severely tough requirements from clients to submit very creative proposals. Also, R&D teams are widely accepted as relatively creative teams because their responsibilities are focused on suggesting innovative techniques to make their companies remain competitive in the market. SI teams are usually ad hoc, while R&D teams are permanent on an average. By taking advantage of these characteristics of the two kinds of teams, we will prove the validity of the proposed research questions. To obtain the survey data, we accessed 7 SI teams (74 members), and 6 R&D teams (63 members), collecting 137 valid questionnaires. PLS technique was applied to analyze the survey data. Results are as follows. First, in case of SI teams, organizational learning culture affects individual creativity significantly. Meanwhile, knowledge management participation has a significant influence on Individual creativity for the permanent teams. Second, degree centrality Influences individual creativity significantly in case of SI teams. This is comparable with the fact that structural hole has a significant impact on individual creativity for the R&D teams. Practical implications can be summarized as follows: First, network structure of ad hoc team should be designed differently from one of permanent team. Ad hoc team is supposed to show a high creativity in a rather short period, implying that network density among team members should be improved, and those members with high degree centrality should be encouraged to show their Individual creativity and take a leading role by allowing them to get heavily engaged in knowledge sharing and diffusion. In contrast, permanent team should be designed to take advantage of structural hole instead of focusing on network density. Since structural hole can be utilized very effectively in the permanent team, strong arbitrators' merits in the permanent team will increase and therefore helps increase both network efficiency and effectiveness too. In this way, individual creativity in the permanent team is likely to lead to organizational creativity in a seamless way. Second, way of Increasing individual creativity should be sought from the perspective of organizational culture and knowledge management. Organization is supposed to provide a cultural atmosphere in which Innovative idea suggestions and active discussion among team members are encouraged. In this way, trust builds up among team members, facilitating the formation of organizational learning culture. Third, in the ad hoc team, organizational looming culture should be built such a way that individual creativity can grow up fast in a rather short period. Since time is tight, reasonable compensation policy, leader's Initiatives, and learning culture formation should be done In a short period so that mutual trust is built among members quickly, and necessary knowledge and information can be learnt rapidly. Fourth, in the permanent team, it should be kept in mind that the degree of participation in knowledge management determines level of Individual creativity. Therefore, the team ought to facilitate knowledge circulation process such as knowledge creation, storage, sharing, utilization, and learning among team members, which will lead to team performance. In this way, firms must control knowledge networks in permanent team and ad hoc team in a way mentioned above so that individual creativity as well as team performance can be maximized.

• 한국재료학회:학술대회논문집
• /
• 한국재료학회 1992년도 춘계학술발표회
• /
• pp.26-27
• /
• 1992

반도체 기억소자 contact hole의 선택적 충진의 최적 조건을 연구하기 위하여 무전해Ni도금방법을 채택하여 실리콘의 활성화와 선택적 도금의 공정조건이 Contact Hole 도금피막의 제반 특성에 미치는 영향을 조사하였다. p형 실리콘 100 소지 표면의 활성화 처리는 RCA처리에 의해 먼저 표면을 세척한 다음 온도, PdCl$_2$농도, 시간. 교반의 영향을 조사하였다 전처리의 최적조건은 7$0^{\circ}C$, 0.5M HF, ImM PdCl$_2$, 2mM EDTA, 90second이었다. 무전해도금은 NiS0$_4$.6$H_2O$를 DMAB를 환원제로 하여 온도, DMAB 농도, pH, 도금시간의 영향을 조사하였다. 무전해 도금 피막은 비교적 우수한 접촉저 항을 나타냈다. 1$\mu$m의 도금막을 얻는 데 본 실험조건에서 DMAB의 농도가 8mM일 때 30 분이 소요되었다. 도금막의 표면은 온도가 낮을수록 pH가 높을수록 평활하였고,특히 온도 6$0^{\circ}C$와 pH6.8에서 가장 우수하였다. 미세경도는 600Hv 정도였으며, 결정립의 크기 가 증가할수록 저항과 미세경도가 감소하였다.