• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2006년도 춘계학술대회 논문집
• /
• pp.103-104
• /
• 2006

Wear of valve seating face and seat insert seating face influence the performance of engine, so they are important. To manufacture good quality valve and seat insert which have wear resistance the relations between wear factors and wear of the two seating faces have to be inspected. Cycle number is one of the important wear factors wearing the two seating faces and it can translate into mileage in rear car. But little is blown. Test variable is only cycle number and the cycle numbers are $2.0{\times}10^6,\;4.0{\times}10^6\;6.0{\times}10^6,\;8.0{\times}10^6$. And the other test conditions were fixed. Rmax of valve seating face and seat insert seating face increase linearly as cycle number is increased. Rmax of valve seating face were smaller than seat insert seating face in each cycle number. Reaction production by tribological reaction and sliding wear was found on the two faces.

• 한국자동차공학회논문집
• /
• 제15권4호
• /
• pp.101-107
• /
• 2007

This study investigated the wear of the valve and seat insert seating faces. A tester, an exhaust valve and a seat insert were used. Test variables were cycle numbers ($2{\times}10^6,\;4{\times}10^6,\;6{\times}10^6\;and\;8{\times}10^6$) and Hz (10Hz and 25Hz). The other test conditions such as temperature ($350^{\circ}C$), fuel (LPG) and load (1960N) were fixed. The 10Hz tests indicated that the average Rmax of the valve increased at the rate of $7.76{\mu}m/10^6$ cycles starting from $29.42{\mu}m$ at the $2{\times}10^6$ cycles and that of the seat insert increased at the rate of $8.57{\mu}m/10^6$ cycles starting from $34.19{\mu}m$ at the $2{\times}10^6$ cycles. The 25Hz tests indicated that the average Rmax of the valve increased at the rate of $1.58{\mu}m/10^6$ cycles starting from $74.2{\mu}m$ at the $2{\times}10^6$ cycles and that of the seat insert increased at the rate of $1.25{\mu}m/10^6$ cycles starting from $83.95{\mu}m$ at the $2{\times}10^6$ cycles. The tribochemical reaction product covered the two seating faces, preventing the wear of the seating faces. As cycle numbers became greater, the average Rmax of the seating faces became greater, but the increase rate varied significantly depending on the Hz. The wear mechanism of the two faces was investigated through the tribochemical reaction.

• 대한통합의학회지
• /
• 제10권3호
• /
• pp.131-140
• /
• 2022

Purpose : Although many studies have explored the effect of seating side angles on the spinal curve and surrounding muscles during seating, only a few studies have investigated the effect of different seating face angles on different lower limb and deep trunk muscles. Therefore, this study investigated the effects of seating surface angles (0 degrees, 10 degree anterior, and 10 degree rear) on lower extremity and deep trunk muscles in healthy adults. Methods : Thirty people were asked to sit once on each seating surface three times during the day, and their muscle thicknesses were measured by ultrasound while sitting. The method of sitting was the same when sitting on the three seating surfaces. Results : From the comparison results of the muscle thicknesses according to the seating surface angles, a significant difference existed in the muscle thicknesses of the vastus medialis, vastus medialis oblique, vastus intermedius, soleus and gastrocnemius (p<.05). However, no significant difference was found in the transversus abdominis, internal obliques, rectus femoris and vastus lateralis (p>.05). Conclusion : Our findings revealed that the lower back load decreases, the leg load increases, and the legs specific muscles are affected as the body tilts forward when sitting on the seating surface inclined forward. Therefore, it is possible to suggest a forwardly inclined seating surface that reduces lower back loads and utilizes the posture-maintaining muscles of the legs when sitting in a person with a poor sitting posture or lower back pain at ordinary times.

• Tribology and Lubricants
• /
• 제18권1호
• /
• pp.34-41
• /
• 2002

This paper presents the contact thermal behaviors of mechanical seals depending on the contacting face geometry. Using the finite element analysis, the temperature distribution, thermal distortion and leakage have been analyzed as functions of sealing gap and rotating speed of the seal ring shaft. The FE results indicate that the inclined contacting face may be more effective and stable based on the results of thermal characteristic analysis if the seal ring has been designed with a same thermal capacity between conventional rectangular sealing faces and inclined seating surface of seal rings.

• Journal of Welding and Joining
• /
• 제20권4호
• /
• pp.517-524
• /
• 2002

An overlaying of the seating surfaces of engine valves by OAW, GTAW or PTA weldings are common practice. The OAW method of a lower torch energy density compared to GTAW and PTA methods produces smoother deposits but the pain size at the vicinity of the interface is increased remarkably up to $30~50{\mu\textrm{m}}$ (that of base metal is about $10\mu\textrm{m}$). It's grain coarsening and the solute dilution are related to the decarburizing during OAW could be minimized by reducing the preheating temperature and by maintaining the carbide precipitates in base metal prior to welding. The formation of columnar structures and carbide precipitation zone in the vicinity of the GTAW welded interface, because of the high heat concentration, causes weakened zone on the valve seat face. The width of the reaction boundary zone is about $50\mu\textrm{m}$ for PTA and GTAW overlaying, and about $150\mu\textrm{m}$ for OAW welding. The smaller width of the reaction boundary zone is the less the solute-dilution rate. Thereby PTA welding may be recommended for overlaying of the seating surfaces.

• 산업경영시스템학회지
• /
• 제41권3호
• /
• pp.108-114
• /
• 2018

One of the most performed action in daily life is standing up from sitting position. As the population of the world is aging at the high rates, people may face problems with reduced muscle strength as well as psychological changes. This can lead elderly people having difficulties with standing up from chair. Now, with the aging trend worldwide, products are being developed that can support the lives of the elderly. This study examines the distribution of hip pressure in relation to the seating positions of the standing assistance seats under development to prevent standing up accidents in older adults. The currently developing standing assistant chair designed to tilt to a maximum angle of 25 degrees. At over $25^{\circ}$, design considers that older people are at risk of thrown back out of that force and that the forces exerted on their arms and legs can be a significant burden to older people. By considering danger of higher than $25^{\circ}$ for older people which is experimented in the basis of static capturing approach in previous papers, it is experimented people with age group of 20~60 on $0^{\circ}$ to $25^{\circ}$ tilting angle on the basis of dynamic capturing method in order to pick convenient angle of inclination. Moreover, tried to find the optimum angle by comparing the hip pressure distribution when seated at the edge of the seat and at the center of the seat with the pressure distribution sensor.