• Journal of Korean Institute of Industrial Engineers
• /
• v.26 no.3
• /
• pp.257-264
• /
• 2000

This research suggested a method by which the driver space can be designed to best accommodate the driver's anthropometric characteristics. Three-dimensional manikins and a variable seating buck were developed and used for this study. Manikins were designed with 18 links comprising the 95th percentile male and 5th percentile female data. The seating buck was built to create various driving environments using the distance and the height between the H-point(hip pivot) of the seat and the AHP(accelerator heel point), the angle of the back rest, the angle of the steering wheel, the vertical distance of the steering wheel, and the location of the T.G.S.(transmission gear shift) knob. Measurements of each variable were collected with a coordinate measuring machine by positioning the 3-D manikin under various combinations of the design factors of the seating buck, which was constructed based on mid-size domestic passenger cars. The data were then converted to the joint angles of the driver. The combination of the measurements for an optimal driving environment is suggested by applying sets of the joint angles at which the driver feels comfortable.

• 제어로봇시스템학회:학술대회논문집
• /
• 1989.10a
• /
• pp.206-210
• /
• 1989

In automobile glass fitting the stud is welded on the window seating panel in order to insert the plastic molding onto the stud. Since this type of process is in general manually done, almost 50% of the output turns out to be failure resulted from work inefficiency and weld inferiority. Therefore, it is required to improve this process for the productivity elevation through the application of the robot.

• Journal of rehabilitation welfare engineering & assistive technology
• /
• v.8 no.3
• /
• pp.205-211
• /
• 2014

The purpose of this document is to provide basic data helpful in selecting seating device material by examining the affects of polyurethane foam material on seating pressure. In order to achieve this study objective, four seats, 6cm in height, were produced in hardness of: 13, 28, 25, and $45kg/cm^2$. To measure the sitting pressure distribution (depending on the characteristics of the produced seats), 10 healthy subjects participated in the experiment. XSENSOR was used a measuring device, and each seat was mounted on a wheelchair simulation. By analyzing the obtained data with Average Pressure(AP), Peak Pressure(PP,), and Contact Area(CA), the sitting pressure was measured for five minutes on each seat. This experiment showed the following results: There were significant differences between the AP, PP, and CA in the seat material (p<0.5). While the hardness of $18kg/cm^2$ showed low pressure, the hardness of $45kg/cm^2$ showed high pressure. This study also showed that seat material made of polyurethane should be considered when selecting seats. If polyurethane foam is used in seat recommendations, it will be recommended to use $18kg/cm^2$ for the proper hardness of the seat material.

• The Journal of Advanced Prosthodontics
• /
• v.3 no.4
• /
• pp.196-203
• /
• 2011

PURPOSE. This study evaluated marginal fit of glass infiltrated alumina cores fabricated using two techniques and their marginal stability after firing cycles of veneering porcelain. MATERIALS AND METHODS. Fifteen standardized all-ceramic crowns were fabricated on a metal die using each technique: slip cast technique of VITA In-Ceram sprint Alumina (Group A as control) and plastic foil matrix technique of Turkom-Cera fused alumina core system (Group B). Copings were compared between groups and within groups at coping stage and after firing each layer of veneering porcelain. A device was used to standardize seating of copings on the metal die and positioning of the specimens under the microscope after each stage of fabrication. The specimens were not cemented and marginal gap was measured using an image analyzing software (Imagepro Express) on the photographs captured under an optical microscope. Two tailed unpaired 't test' was used to compare marginal gaps in two groups and one way ANOVA was used to analyze marginal distortion within each group at 95% confidence interval. RESULTS. The marginal gap was smaller at the coping stage in group B ($60+30{\mu}M$) than group A ($81+21{\mu}M$) with statistical significance. After firing of veneering porcelain the difference was insignificant. At the final stage, both groups exhibited lower mean marginal gaps than at the initial coping stage with the difference of $11.75{\mu}M$ for group A and $11.94{\mu}M$ for group B, but it was statistically insignificant due to high value of standard deviation. CONCLUSION. Within the limitations of this study, it was concluded that both techniques produced copings with comparable and acceptable marginal fit and marginal stability on firing veneering porcelain.