• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.30 no.4 s.247
• /
• pp.379-386
• /
• 2006

The hyper-elastic material has been used gradually and its range was extended all over the industry. The performance prediction of hyper-elastic material was required not only experimental methods but also numerical methods. In this study, we presented the process how to use numerical method for hyper-elastic material and applied it to seat-ring of butterfly valve. The finite element analysis was executed to evaluate the mechanical characteristics of hyper-elastic material. And the optimum model considered conditions and features. According to that model, the load conditions were obtained by using CFD analysis.

• Proceedings of the KAIS Fall Conference
• /
• 2011.05b
• /
• pp.824-827
• /
• 2011

본 논문에서는 자동차 시트 리클라이너 기어의 파인 블랭킹 성형 실험을 통하여 V-링 설치 위치에 따른 기어의 다이 롤 높이 변화를 검토하였다. 3 종류의 다이 편과 가이드 플레이트 편을 설계하여 파인 블랭킹 금형을 제작하였으며 650 ton 파인블랭킹 프레스에서 성형 실험을 수행하였다. 실험으로부터 제품을 취출하여 다이 롤 높이를 측정하여 분석한 결과 기어 모듈과 관계없이 V-링 설치 위치가 가이드 플레이트에서 멀어짐에 따라 다이 롤 높이가 증가함을 파악할 수 있었다. 이와 같은 결과는 향후 파인 블랭킹 금형의 V-링을 설계할 때 다이 롤 높이를 최소화하기 위하여 유용하게 활용될 수 있을 것이다.

• Tribology and Lubricants
• /
• v.12 no.3
• /
• pp.79-84
• /
• 1996

One of the greatest dangers in mechanical face seals is the formation of heat checking and thermal stress cracks on the sliding surfaces. These thermal distortions due to non-uniform heating lead to increase the leakage of the sealed fluids and wear, and with balance of the seal can cause the seal faces to part. In this study heat checking and thermal stress cracks are investigated experimentally. These thermal distortions are explained using the thermal models of the conatct geometries between the seal ring and the seal seat. To overcome these thermal problems, the thermohydrodynamic seal is presented. The newly developed mechanical seal may substantially reduce the friction torque, frictional heating which causes heat checking and thermal stress cracks, and wear.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.24 no.12
• /
• pp.2935-2944
• /
• 2000

Gas tungsten arc(GTA) welding is used to rrpiar the seat ring in swing type check valve in power plant because of its high weld quality. In order to automate the welding process, it is needed to analyze the process of inside pipe girth welding. In this study, the shapes of weld bead on pipe inside and outside were predicted and its validity was investigated. On the assumption that the welding arc had a bivariate gaussian distribution, analytical solution was derived to predict the temperature distribution in pipe weld using mapping under consideration of physical relationships. The size of weld bean could be predicted from this equation and its accuracy was verified by experiments.

• Journal of Auto-vehicle Safety Association
• /
• v.7 no.1
• /
• pp.13-19
• /
• 2015

Recently, Child safety has become one of the issue with Q10 dummy representing large child. The objective of this paper was to evaluate performance of three child restraints system (backless booster, high-back booster and without booster) by changing D-ring location in the rear seat. Sled tests were carried out with a Q 10 in 64km/h frontal impact. Before the dynamic sled tests, we assessed dummy positioning with difference in CRS types and height adjustment positions. Dynamic sled test results indicated that there is different performance of CRS types and belt routing. These test results will use as base line data for development CRS safety performance for Q 10.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 2002.10b
• /
• pp.401-402
• /
• 2002

Diesel engines have many sliding parts with solid body contact. For example, a piston-ring and a cylinder bore, a valve and a valve-seat, a cam and a valve tappet. These parts have a severe wear problem. during engine life times. During these times, the valve tappet has abnormal wear such as scuffing and pitting due to a high hertzian contact stress between the cam and the tappet. Excessive wear problems frequently occur to both the cam and the tappet. To solve these problems, we developed an advanced wear resistant tappet. The developed tappet consisted of a hard-metal wear part and a steel body. To increase a bonding strength, those two parts, were directly bonded to each other. Also to decrease a bonding temperature, we developed the composition of Ni-binder materials in the hard metal. To estimate the wear characteristics of the newly developed tappet, we performed wear tests and engine dynamo tests in order to compare them with a conventional Fe-base tappet. As a result, the newly developed tappet has better wear characteristics than those of the conventional tappet. In addition, we performed a 100,000km field-test, and the newly developed tappet showed much improved wear resistance.

• 한국신재생에너지학회:학술대회논문집
• /
• 2006.11a
• /
• pp.515-518
• /
• 2006

This paper presents the friction and wear characteristics of contact type sealing unit for a water turbine of a small hydro-power generation, which Is to stop a leakage of a circulating water from a outside of an impeller to an inside of a rolling bearing. The surface wear strongly affect to the seal life of a mechanical face seal. In this study, the hardness of a stainless steel in which is a heat-treated is 892.8 in Vickers hardness and the hardness of silicone carbide of SiC is 714.1 in Vickers hardness. The surface hardness of a heat-treated stainless steel is 25% high compared with that of a ceramic material of SiC. The contact modes of rubbing surfaces aye a dry friction a water film friction and a mixed friction that is contaminated by a dust, silt and moistures, etc. These two factors of a contact rubbing modes and a material property are very important parameters on the tribological performance such as a friction and wear between a seal ring and a seal seat. The experimental result shows that the surface hardness of a seal material is very important on the friction coefficient and a wear volume. Thus, the results recommend higher hardness of a seal material, which may reduce a friction loss and increase a wear life of primary seal components

• Journal of the Korean Society for Precision Engineering
• /
• v.19 no.3
• /
• pp.144-151
• /
• 2002

This work focuses on finding out the noise source and the method of reducing the noise level of LPG(liquefied petroleum gas) fuel injector. The noise of LPG injector in operating condition is due to the impact between valve and valve seat. This study shows that if the revolution of engine is increased, the noise of LPG injector will be more serious but it is not nearly affected by the increment of fuel pressure. The source and transmission paths of noise are identified through the analysis of noise generation mechanism and noise spectrum. The sound absorbing material is tested to verify its efficiency of sound absorption thor the LPG injector. The effect of noise reduction of absorbing material is remarkable when the engine speed is high. Consequently two methods of reducing the noise level are suggested from the identified results. The one is to equip the absorbing material on the outer side of injector and the other is to coat with a soft material or equip a soft ring on the surface of impact.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 1987.06a
• /
• pp.50-56
• /
• 1987

A mechanical face seal is most commonly used to seal liquids and gases at various speeds, pressures and temperatures. The primary seal ring is in sliding contact with the seal seat and as a result heat in the vicinity of the interface is generated. Local temperatures at points along the circumferential direction will fluctuate as asperities on the surfaces pass. This kind of fluctuation of temperature has been investigated to take place. This may lead to the hot spots phenomenon between the contacting asperities. Sibley and Allen showed photographic evidence of systemically moving hot spots in the contact zone. The appearance of such a temperature disturbance has been attributed to a kind of thermoelastic instabilities between two surfaces: This involves a feedback loop which comprises localized elevation of frictional heating, resultant localized thermal bulding, localized pressure increase as the result of the bulging and futher elevation of frictional heating as the result of the pressure increase. The heating of hot spots will be continued until the expanded material due to the frictional heating is worn off. Therefore to predict the speed of temperature propagation into the body is essential to the analysis of heat transfer on the edge of the seal.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.13 no.6
• /
• pp.37-45
• /
• 2014

Ball valves are used as a key element in the process industries. The industrial development of valves has increased steadily, but continued improvement requires high design reliability and long service life. Currently, the development of high performance valves is not easy because of the lack of relevant technology in Korea. Valves are being imported at a level of up to 58 percent of the domestic market, which represents a value of almost 7 million US dollars. Therefore, in this work, the improvement of the design and performance of industrial valves has been studied in an attempt to achieve valves that will have longer service life and better output during operation. The structural stability was evaluated using the ANSYS FSI (Fluid-Structural Interaction) module. Moreover, to obtain maximum product reliability, torque analysis simulation was performed to compare and experimental results. The simulation results were used to predict the change in torque by changes in shape, thereby reducing the time and cost of manufacturing a number of prototypes for experimental validation.