• Journal of Powder Materials
• /
• v.26 no.2
• /
• pp.112-118
• /
• 2019

Infiltration is a popular technique used to produce valve seat rings and guides to create dense parts. In order to develop valve seat material with a good thermal conductivity and thermal expansion coefficient, Cu-infiltrated properties of sintered Fe-Co-M(M=Mo,Cr) alloy systems are studied. It is shown that the copper network that forms inside the steel alloy skeleton during infiltration enhances the thermal conductivity and thermal expansion coefficient of the steel alloy composite. The hard phase of the CoMoCr and the network precipitated FeCrC phase are distributed homogeneously as the infiltrated Cu phase increases. The increase in hardness of the alloy composite due to the increase of the Co, Ni, Cr, and Cu contents in Fe matrix by the infiltrated Cu amount increases. Using infiltration, the thermal conductivity and thermal expansion coefficient were increased to 29.5 W/mK and $15.9um/m^{\circ}C$, respectively, for tempered alloy composite.

• Journal of Biosystems Engineering
• /
• v.22 no.1
• /
• pp.41-48
• /
• 1997

A nondestructive quality inspection technique using acoustic impulse response method was studied to investigate the feasibility of egg shell inspection. An experimental system was built to generate impact force, to measure the response signal and to analyze the frequency spectrum. This system includes an impulse generating unit, an egg holding seat, a microphone with preamplifier, and a digital oscilloscope connected to Personal Computer by RS-232C interface. The factors such as impulse generating method, egg holding method, and sensor location were evaluated by analyzing the power spectrum density of the measured signal. The results obtained are summarized as follows : 1. From the sampled eggs, the proper conditions for detecting damaged eggs were found as followings; ceramic for the impact ball material, rubber for egg seat material, 20 degrees for an impact angle of pendulum, 10mm for the distance between egg and sensor, the sharp side for impacting part, and 180 degrees for the location of sensor. 2. Examination of the Fourier transformed analysis in beth normal and damaged eggs revealed that those factors such as the resonant frequency, a number of peak frequencies and the magnitude of power spectrum were important to detect damaged eggs.

• Journal of Welding and Joining
• /
• v.35 no.3
• /
• pp.62-67
• /
• 2017

The automotive industry is in constant pursuit of alternative materials and processes to address the ever changing needs of their customers and the environment. Applications of laser welding have increased steadily in recent years due to its benefits including high speed, high productivity, and high energy density of heat source. This paper investigated the relationship between laser welding parameters and penetration characteristics. The Welding power was fixed at 5kW and welding speeds were varied for the thickness of the workpiece material. Full penetration occurred in the energy per unit area of $21J/mm^2$. The hardness of the weld zone was different for each strength of the workpiece material, however the lowest hardness values were the same in the heat-affected zone.

• Journal of Korean Society of Occupational and Environmental Hygiene
• /
• v.34 no.1
• /
• pp.8-13
• /
• 2024

Objectives: To evaluate the levels of exposure to organic compounds during aircraft disinfection and seat cover replacement operations. Methods: According to the working schedule, organic compounds were collected using activated carbon tubes and then analyzed by GC/FID and GC/MSD. Results: In the disinfection task, the main substances listed in the material safety data sheet (MSDS) of the disinfectant were not detected. However, 1-bromopropane, which had been used in the previous task of replacing seat covers, was detected at a level of 2.37 ppm at the measurement time. During seat cover replacement, bonding workers were exposed to 2.48 ppm on an eight-hour time-weighted average, and seat cover replacement workers were exposed to 0.22 ppm. Conclusions: It is necessary to ensure the reliability of MSDS. A work environment management system is necessary when different companies alternate working in the same place.

• Proceedings of the KSR Conference
• /
• 2007.11a
• /
• pp.222-228
• /
• 2007

In order to solve the problem of traffic holdups and environmental pollution(contamination), several metropolises are operating the subway and many local government plans hereafter the light rail vehicle operation and it is in the process of preparing. This point of time, it need to evaluate the comfortable characteristic of the seat which is closely connected with passenger and it should be reflected to the product design through the data analysis. The methods of the comfortable characteristic evaluation should be considered to various methods from physical factor to psychological factor. Among these, the most universal and possible quantitative measurement estimate through 'Body pressure measurement system'. From this paper, it was measured the body pressure of the subway seat which is in the process of operating in a domestic and it will be compared and analyzed the material & seat shape, so we evaluated the comfortable characteristic of the short-distance transportation railway vehicle. It was operated the man and woman who belongs in standard shape of Korean, we compared and analyzed the Peak position where the body pressure is visible and body pressure spread out.

• Polymer(Korea)
• /
• v.30 no.5
• /
• pp.402-406
• /
• 2006

New antibacterial Polyurethane foams for car seat with Urushiol extracted from a natural lacquer were prepared. Influences of antibacterial agent's concentration on the reactivity with isocyanate and the mechanical properties of foams were investigated. It was observed that the urethane formation reaction was delayed a little when the amount of Urushiol was increased. However, the foams made using Urushiol showed similar property to the neat polyurethane foam. In terms of antibacterial property, the foams prepared with Urushiol showed better performance than the neat polyurethane foam.

• Proceedings of the KIEE Conference
• /
• 1999.07a
• /
• pp.430-432
• /
• 1999

In this paper, magnetic field inside and outside express railway train is analysed by use of finite element method. We find that high permeability material reduces magnetic field inside train more than thick material. We also know windows in train does not have influence on magnetic field at seat in train.

• Journal of the Korean Society for Precision Engineering
• /
• v.21 no.3
• /
• pp.100-108
• /
• 2004

Contamination of environment induces the shortage of drinkables. In this trend, the leakage of water that occurs by breakage or erosion of rubber valve seats is serious problem. Rubber is apt to cause breakage between two materials when they contact with each other. The possible way to avoid leakage of water by damage and breakdown of rubber is to replace that with metal. Because of this reason, nowadays, rubber is being substituted with metal as valve seat materials for water works. In tribology, a severe from of wear is characterized by local, macroscopic material transfer, removal, or formation of surface protrusions when two solid surfaces experience relative sliding under load. One of the major problems in sliding of metals is galling due to bad surface quality. Experimentally, there are various elements which influence on incipient galling, such as hardness, surface roughness, temperature, load, velocity and external environments. This paper is aimed at verifying the galling tendencies according to hardness, surface roughness, load and velocity and showing how much effect the factors have on the galling tendencies.

• Journal of Korean Society of Steel Construction
• /
• v.27 no.1
• /
• pp.99-108
• /
• 2015

The partially restrained smart CFT (concrete filled tube) column-to-beam connections with top-seat split T connections show various behavior characteristics according to the changes in the diameter and tightening force of the fastener, the geometric shape of T-stub, and material properties. This paper presents results from a systematic three-dimensional nonlinear finite element study on the structural behavior of the top-seat split T connections subjected to cyclic loadings. This connection includes super-elastic shape memory alloy (SMA) T-stub and rods to obtain the re-centering capabilities as well as great energy dissipation properties of the CFT composite frame. A wide scope of additional structural behaviors explain the influences of the top-seat split T connections parameters, such as the different thickness and gage distances of split T-stub.

• Journal of Powder Materials
• /
• v.6 no.2
• /
• pp.163-170
• /
• 1999

Engine valve seat is a functionally important part for maintaining engine performance. The progress of automotive technology has increased the severity of conditions to which it is exposed, especially as regards LPG fuel engines and turbocharger. Therefore, it requires excellent heat and wear resistance to meet the severe condition inside the engine. In the present study, effects of solid lubricants such as CaF$_2$, MnS and MoS$_2$ on microstructure and mechanical properties of sintered Fe alloys for valve srats have been investigated for the development of valve seat material with high temerature wear resistance. As a results of engine simulation test, 0.5 wt% CaF$_2$ specimen showed the most excellent property, but in the overall aspect of view valve recession has increased with increasing the amount of solid lubricants.