• Korean Journal of Materials Research
• /
• v.1 no.4
• /
• pp.221-228
• /
• 1991

In this study we have investigated the sealing characteristics of glasses suitable for producing the magnetic gap of the ferrite head cores which have been widely used for VTR and computer magnetic heads. $PbO-B_2O_3$ g1asses were evaluated by measuring microhardness, thermal expansion coefficient and sliding wear resistance. Concentration distribution of elements at the interface was observed by WDS. wettability was measured by high temperature microscopy. The results were as follows ; 1. In sealing glasses of $PbO-B_2O_3$ system, thermal expansion coefficient and wear volume were increased with increasing PbO content, and were decreased with increasing $B_2O_3$ content. 2. The contact angle of $PbO-B_2O_3$ Systems was mainly influenced by PbO content. 3. The sealing temperature showed a tendency to decrease proportionally with the increase of the coefficient of thermal expansion. 4. The diffusion at the interface between Mn-Zn single crystal ferrite and sealing glasses of $PbO-B_2O_3$ system was dominated by small amount of diffusion of ferrite content into glass part, which was very little affected by sealing heat treatment time.

• Korean Journal of Materials Research
• /
• v.28 no.12
• /
• pp.732-737
• /
• 2018

We develop a purification process of $Hg_2Br_2$ raw powders using a physical vapor transport(PVT) process, which is essential for the fabrication of a high performance acousto-optic tunable filter(AOTF) module. Specifically, we characterize and compare three $Hg_2Br_2$ powders: $Hg_2Br_2$ raw powder, $Hg_2Br_2$ powder purified under pumping conditions, and $Hg_2Br_2$ powder purified under vacuum sealing. Before and after purification, we characterize the powder samples through X-ray diffraction and X-ray photoelectron spectroscopy. The corresponding results indicate that physical properties of the $Hg_2Br_2$ compound are not damaged even after the purification process. The impurities and concentration in the purified $Hg_2Br_2$ powder are evaluated by inductively coupled plasma-mass spectroscopy. Notably, compared to the sample purified under pumping conditions, the purification process under vacuum sealing results in a higher purity $Hg_2Br_2$ (99.999 %). In addition, when the second vacuum sealing purification process is performed, the remaining impurities are almost removed, giving rise to $Hg_2Br_2$ with ultra-high purity. This high purification process might be possible due to independent control of impurities and $Hg_2Br_2$ materials under the optimized vacuum sealing. Preparation of such a highly purified $Hg_2Br_2$ materials will pave a promising way toward a high-quality $Hg_2Br_2$ single crystal and then high performance AOTF modules.

• Journal of the Korean Ceramic Society
• /
• v.43 no.12 s.295
• /
• pp.839-845
• /
• 2006

Graphite has hexagonal closed packing structure with two bonding characteristics; (1) van der waals bonding between c axis, and (2) covalent bonding in the a and b axis. The weak van der waals bonds cause self-lubricant property, and the strong covalent bonds cause excellent electric and thermal conductivity. Furthermore, graphite is chemically very inert because of the material composed of only carbon elements. Thus, graphite is very useful for mechanical sealing materials. However, Graphite have porous microstructure because starting materials of graphite produce many volatile during the manufacturing processes. This causes low density of graphite, which is unsuitable for the mechanical sealing materials. Thus, further impregnation process is generally needed to enhance the graphite density. In this work, high density graphite is prepared with the principle of densification when coke and pitch binder, prepared from thermal treatment of coal tar pitch, become dehydrogenation during graphitization or carbonization.

• Proceedings of the Korean Fiber Society Conference
• /
• 2007.11a
• /
• pp.239-240
• /
• 2007

• Journal of Soil and Groundwater Environment
• /
• v.7 no.1
• /
• pp.41-51
• /
• 2002

Recently, domestic waste landfills are constructed sometimes on seashore area to provide large landfill area. In order to strengthen the foundation of landfills and to prevent the infiltration of leachate through the bottom, many cases of constructing cement hardened liners on seashore clays are found. In these cases, it is possible to have cracks in the hardened liners due to settlement with waste load since the stiffness of the hardened liner Is greater than that of clay liners. In this study, the capability of Self-Sealing and Self-Healing (SSSH) liner made with a seashore clay in the metropolitan landfill to prevent the percolation of water and leachate is examined using flexible-wall permeameter test and using uniaxial compression test. Applicability of SSSH to weathered granitic soil is also examined for self-sealing capabilities. The result of Flexible permeameter test for SSSH with the seashore clay showed that permeability obtained was lower than permeability criteria of Korean waste management law. The permeability and strength characteristics of SSSH with granitic soil and bentonite showed better results than with the seashore clay.

• Tribology and Lubricants
• /
• v.14 no.2
• /
• pp.21-25
• /
• 1998

This paper presents the experimental results of the friction characteristics of double liptype oil seals which show an improvement in sealing performance over single lip-type oil seals. The major differences between two oil seals are the number of contact lip, and seal materials; Nitrile Butadine Rubber(NBR) and urethane rubber. The measured results show that the friction torques of double lip seals show 12-17% increases compared with those of single lip-type seals. But the sealing performance and service life of double lip oil seals have been increased and stabilized due to an optimized design of the seal lip and material properties.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 2004.11a
• /
• pp.209-212
• /
• 2004

The O-ring seal is a usual component part in various mechanical apparatuses for sealing that makes efficient performance of the equipments. The sealing performance of 0-ring is effected in environments of the O-ring seal, like that applied pressures, working temperatures, interferences and materials. In this paper, an pressurized, NBR O-ring is calculated by experimental methods and analysed numerically using the MARC finite element program. The calculated experimental and FEM results showed that the Contact force O-ring decreases as a function of temperature.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 1998.04a
• /
• pp.307-313
• /
• 1998

This paper presents the experimental results of the friction characteristics of double lip-type oil seals which show an improvement in sealing performance over single lip-type oil seals. The major differences between two oil seals are the number of contact lip and seal materials; Nitrile Butadine Rubber(NBR) and urethane rubber. The measured results show that the friction torque of double lip seals shows 12-17% increases compared with those of single lip-type seals. But the sealing performance and service life of double tip oil seals have been increased and stabilized due to an optimized design of the seal lip and material properties.

• Tribology and Lubricants
• /
• v.22 no.1
• /
• pp.20-25
• /
• 2006

The stress behavior analysis of a-rings and packing for a LPG filling unit has been presented using a finite element analysis technique by non-linear MSC/MARC program. The sealing performance and endurance of a-rings and packing are affected by working conditions such as filling pressure, friction coefficient, compression ratio, and material properties. The elastomeric polymers of O-rings and packing are nitrile butadiene rubber (NBR) and polytetrafluoroethylene (PTFE), which are selected as proper materials of a-rings and packing based on the stress analysis results. The calculated FEM results showed that the proper material of O-ring is NBR as a secondary sealing component and the recommended material of packing is PTFE as a primary sealing unit during a LPG filling process.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2009.09a
• /
• pp.1283-1288
• /
• 2009

In general steel sheet piles are used in the containment system, which are vertical barrier systems for waste disposal and landfill purposes, and roads in excavation for temporary structure. This paper presents case study of the use of an interlocking sheet pile for water and containment. Cut-off Z-type sheet pile joints are investigated to determine their permeability from the field test. Four different joint sealing materials are used in field test. The results showed joint permeability is significant time-dependent and joint-dependent. These are explored and conclusions on permeability characteristics of different sealants are noted. A case study gives a design example as well as suggestion on permeability and water tightness can be implemented in using the sheet pile barrier in civil and environment works. From the test results, the effective sealing programs of sheet pile interlocks are suggested.