• 동력기계공학회지
• /
• 제18권5호
• /
• pp.106-114
• /
• 2014

For the purpose of development of polyurethane sealing material, polyurethane resins reinforced with CuO were prepared from polyol and MOAC(4,4'-Methylenebis(2-chlorobenzeneamine)). And the effects of compositions on the mechanical properties of the reinforced polyurethane resin were experimentally examined. The polyurethane resin got to be thermally decomposed at $260^{\circ}C$ and completely carbonized around $500^{\circ}C$. Tensile strength, elongation and hardness of the polyurethane resin increased with the content of MOCA. CuO was uniformly dispersed in the polyurethane resin by 1 minute's ultrasonic radiation. Tensile strength, elongation and hardness of the polyurethane resin reinforced with CuO increased with the content of CuO. Tensile strength and hardness of the reinforced polyurethane resin increased with particle size of the CuO, but elongation decreased. CuO showed higher tensile strength and hardness than any other additives, and lowest elongation.

• Steel and Composite Structures
• /
• 제25권5호
• /
• pp.571-579
• /
• 2017

The grid structure with bolt-sphere joints is widely adopted by industrial plants with suspending crane. The alternating reciprocating action of the suspending crane will cause fatigue problems of the grid structure with bolt-sphere joints with respect to the rod, the cone, the sealing plate, the bolt ball and the high strength bolt; while the fatigue of the high strength bolt is the key issue of fatigue failure. Based on efficient and smooth loading equipment with the AMSLER fatigue testing machine, this paper conducted a constant amplitude fatigue test on 18 M20 and 14 M30 high strength bolts with 40Cr material, and obtained 19 valid failure points, 9 unspoiled points with more than 2 million cycles, and 4 abnormal failure points. In addition, it established the constant amplitude fatigue design method, ${[{\Delta}{\sigma}]_{{2{\times}10}}{^6=58.91MPa}$, and analyzed the stress concentration and the fatigue fracture of high strength bolts. It can be explained that the geometrical stress concentration of high-strength bolt caused by spiral burr is severe.

• 한국생산제조학회지
• /
• 제20권6호
• /
• pp.714-719
• /
• 2011

The surface roughness depending on the machining method is very important because is produce a finished product through riveting, sealing, bonding, and special paint in order to curb the turbulence and air resistance which occur between the sheets. Aluminum alloy 2024 which is widely used for interior and exterior material of aircraft are tested. Jin-young JW-60C wire cutting machine was used in this experiment. In this paper, the experimental investigation has been performed to find out the influence of the surface roughness and surface shape characteristics on the wire-cut EDM of discharge energy in aluminium alloy 2024. The selected experimental parameters are peak current, no-load voltage, off time and feed rate. The experimental results give the guideline for selecting reasonable machining parameters. The high discharge energy on the idle time, almost no change in surface roughness can be seen.

• Journal of Advanced Marine Engineering and Technology
• /
• 제30권5호
• /
• pp.623-628
• /
• 2006

Laser material processing is a very fast advancing technology for various industrial applications. because of many advantages. Its major advantage of less and controlled heat input has been exploited successfully for the very critical application of aluminium alloy welding. This study suggested the occurrence source of weld-defects and its solution methods in a welding of lithium ion battery by pulsed Nd:YAG laser. In experiment. battery case has changed over joint geometry from welding of side position to flat one. In the case of a electrolyte injection hole in order to seal it. welding is carried out after pressing Al ball. At this time. an eccentric degree. contact length and gap are worked as a major parameters. As improving the method of Al ball pressing. it was able to reduce an eccentricity. increase the contact length and decrease gap. As a results of a experiment. a sound weld bead shape and crack-free weld bead can be obtained.

• 한국마린엔지니어링학회:학술대회논문집
• /
• 한국마린엔지니어링학회 2005년도 전기학술대회논문집
• /
• pp.339-343
• /
• 2005

Laser material processing is a very fast growing technology for various industrial applications, because of many advantages. Its major advantage of less and controlled heat input has been exploited successfully for the very critical application of aluminium alloy welding. This study suggested the occurrence source of weld-defects and its solution methods in a welding of lithium ion battery by pulsed Nd:YAG laser. In experiment, battery case has changed over joint geometry from welding of side position to flat one. In case of a electrolyte injection hole in order to seal it, welding is carried out after pressing Al ball. At this time, an eccentric degree, contact length and gap are worked as a major parameters. As improving the method of Al ball pressing, it was able to reduce an eccentricity, increase the contact length and decrease gap. As a results of a experiment, a sound weld bead shape and crack-free weld bead can be obtained.

• Restorative Dentistry and Endodontics
• /
• 제14권2호
• /
• pp.31-37
• /
• 1989

The purpose of these study was to compare the sealing ability of a injection-molded thermoplasticized gutta-percha and silver amalgam as retroseal material in vitro. Sixty two upper and lower extracted human teeth with single root were randomly selected and instrumented in a conventional method with H-file. After instrumentation the root canal was obturated with gutta-percha by lateral condensation technique with AH26 and an apicoectomy was performed by beveling the root tip 45 angle. In the experimental group 1 and 2, a class I preparation was made and filled with silver amalgam or gutta-percha and in the experimental group 3 an apicoectomy only was performed. All specimens were immersed in black Indian ink, decalcified and cleared. The depth of dye penetration into the canals were evaluated by califer. The results were as follows ; 1. The experimental group 1 displayed the smallest mean dye penetration as 0.45mm. 2. The experimental group 3 displayed the greatest mean dye penetration as 0.65mm. 3. There was the difference in dye penetration between each group, but the difference was not statistically significant(P>0.05).

• 대한소아치과학회지
• /
• 제3권1호
• /
• pp.33-39
• /
• 1976

The present in vitro study was undertaken to evaluate the initial marginal sealing ability of the sealant known as Nuva-Seal to seal cavity margins when used in conjunction with Adaptic and Nuva-Fil restorative materials. The results were as follows; 1. Where each Adaptic and Nuva-Fil restorative material was filled, showed the greatest degree of marginal leakage. 2. Where Adaptic and Nuva-Fil restorative materials were filled after acid etched surrrounding enamel surface adjoining the cavity margins, showed some degree of marginal leakage. 3. Where the Nuva-Seal was applied after acid etching a) to the cavity walls and the peripheral enamel surface adjoining the cavity margins, b) only to the surrounding enamel surface adjoining the cavity margins, and c) over the restorations and the peripheral enamel surface, showed complete absence of marginal leakage of Adaptic and Nuva-Fil restorative materials. 4. Where the Nuva-Seal was applied with the same methods as above, and restorations were placed on thermal stress also showed complete absence of marginal leakage of Adaptic and Nuva-Fil restorative materials.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2009년도 추계 학술논문 발표대회
• /
• pp.183-189
• /
• 2009

In this study, the growth diagnosis of root is analyzed through plant's auxanology point of view, and the inductive root barrier ability of panel type waterproofing method which is designed to deal with it, is confirmed positively through long term(2 years) mock-up test. Moreover, basic ideas for inductive root barrier design in joint is presented through this study. The experiment result for the root barrier of sealed A-type during 24 months, there were no damages found on the waterproofing layer. -urethane sealing material was used to apply for waterproofing of joint- for roots. As the result, it was confirmed that it is possible to maintain the root barrier of method through applying inductive root barrier design such as the installation of decreasing space of bearing power which considers the growth diagnosis of root, even if the root barrier was not secured.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2004년도 추계학술대회 논문집 전기물성,응용부문
• /
• pp.233-236
• /
• 2004

Recently, the polymer insulators that are used for high voltage applications have some advantages such as light weight, small size, vandalism resistance, hydrophobicity and easy making process. During outdoor service of polymer insulators, the surface of the insulating material is frequently subjected to moisture and contamination that lead to dry band arcing. Their tracking resistance, erosion resistance, end sealing and shed design are very important because dry band arcing causes degradation of polymer surface. The shape design of porcelain insulator is formalized but design standard for polymer insulator is no standardized up to now, much research is necessary in real condition. In this paper, the surface and tracking properties of polymer suspension insulator for power transmission is investigated with ICP-AES, SEM, EDX, tracking wheel test and flashover voltage test. The diagnosis of insulator sample in tracking test hass been analyzed by leakage current STRI Guide and thermal image.

• Nuclear Engineering and Technology
• /
• 제53권10호
• /
• pp.3438-3448
• /
• 2021

Dynamic seals are one of the critical components of Absorber Rod Drive Mechanism of Fast Breeder Reactors, requiring separate experimental development. Their significance can't be overemphasized considering that the availability and re-usability of Control Rod Drive Mechanisms of Fast Breeder Test Reactor is governed by the failure rate of dynamic seals (bellows). For prototype and subsequent Fast Breeder Reactors in India, choice of the dynamic seal is changed to an in-house designed & developed labyrinth type V-ring seal. The present work is related to the numerical investigations carried out to gain insights into the sealing mechanism and the thermal behaviour of these seals. The results indicate that the seal geometry is very important for obtaining optimum performance. By changing the geometry of the present seal, performance enhancement by more than 50% in important indices is obtained. Further, the results point out that caution shall be exercised when the seal material & its operating temperature are changed. Also, the numerical model developed in this study will be useful for developing more robust dynamic seals in future.