• Nuclear Engineering and Technology
• /
• v.53 no.6
• /
• pp.1756-1768
• /
• 2021

The containment filtered venting system (CFVS) filters the atmosphere of the containment building and discharges a part of it to the outside environment to prevent containment overpressure during severe accidents. The Korean CFVS has a tank that filters fission products from the containment atmosphere by pool scrubbing, which is the primary decontamination process; however, prediction of its performance has been done based on researches conducted under mild conditions than those of severe accidents. Bubble behavior in a pool is a key parameter of pool scrubbing. Therefore, the bubble behavior in the pool was analyzed under various injection flow rates observed at the venturi nozzles used in the Korean CFVS using a wire-mesh sensor. Based on the experimental results, void fraction model was modified using the existing correlation, and a new bubble size prediction model was developed. The modified void fraction model agreed well with the obtained experimental data. However, the newly developed bubble size prediction model showed different results to those established in previous studies because the venturi nozzle diameter considered in this study was larger than those in previous studies. Therefore, this is the first model that reflects actual design of a venturi scrubbing nozzle.

• Journal of Korean Society for Atmospheric Environment
• /
• v.34 no.5
• /
• pp.659-667
• /
• 2018

$NO_x$ and $SO_2$ are mainly generated in the combustion of fossil fuels, and they cause secondary aerosol formation and acid rain in the atmosphere. Many studies have been conducted on the wet scrubbing process which can simultaneously reduce $NO_x$ and $SO_2$ at relatively low temperature. In this study, we conducted an experimental study on wet scrubbing by using NaOH solution. Especially, this study focuses on $NO_x$ and $SO_2$ removal characteristics by varying $NO_2/NO_x$ ratio and $SO_2$ concentration.

• Proceedings of the Korean Society of Agricultural Engineers Conference
• /
• 2005.10a
• /
• pp.598-603
• /
• 2005

Biogas produced from anaerobic digestion processes has about 60% of methane and about 40% of carbon dioxide. Raw biogas can be used in internal combustion engines either spark ignition or diesel engines. Since the gas has relatively low calorific values, engine power also is lower than rated power values. Modified engines or biogas-specific engines have been utilized in order to increase efficiency. Another option is gas cleansing for increasing its calorific values. A couple of European countries adopted this approach in using biogas for one of transportation fuels, such as $CO_2$ scrubbing with water or special solutions. This study reports the results of water scrubbing for reducing $CO_2$ concentration. In 2.5m-high PVC pipe accepting water, $CO_2$ reduction rates were investigated. When flow rate of $CO_2$ and air mixture was about 5 LPM, $CO_2$ concentration was decreased up to 70%. Higher calorific biogas through water scrubbing is expected to be applied to various commercial engines without costly modification.

• The Journal of the Korean dental association
• /
• v.18 no.5 s.134
• /
• pp.355-359
• /
• 1980

64 dental students who had brushed their teeth with scrubbing method, using 'W' dentifirice for a long lime, were made to practise either scrubbing or Bass method. using one of the 'W','X','Y','Z' toothpaste instead of only 'W' paste for recent 3 weeks. Dental plaque on the teeth of every students were carefully examined compared the results. The simplified oral hygiene index was applied for this purpose and following conclusions were achieved. 1) The Scrubbing method of tooth-paste 'X', Bass method of tooth-paste 'X', and the Bass method of tooth-paste 'Z' had an obvious effect to inhibition of accumulation of plaque. 2) In the tooth brushing method, the scrubbing and Bass are both effective in reducing the plaque accumulation 3) The tooth paste 'X' has the most effectiveness in reducing the plaque accumulation among four tooth pastes 4) The difference in the value of plaque index between the tooth pastes, 'W' and 'X' was only significant statisticallay

• Proceedings of the Korea Air Pollution Research Association Conference
• /
• 2006.04a
• /
• pp.125-126
• /
• 2006

• Journal of the Society of Naval Architects of Korea
• /
• v.60 no.3
• /
• pp.186-192
• /
• 2023

According to the regulation on the pollution of the marine environment, SOx emission from ships has to be reduced. A SOx scrubbing system installed in a funnel of a ship is considered in order to reduce SOx emission. A scrubbing layer with a porous material is present in the funnel to increase the contact area between exhaust gas and water. In this study, experiments on the pressure drop characteristics in the scrubbing layer are conducted to investigate the effect of the scrubber on the engine load. The pressure drop according to flow rate of air instead of exhaust gas was measured for fillers such as sphere, pall ring and saddle in the scrubbing layer. First of all, porosity is experimentally measured for the three types of filler and it is confirmed that the porosity of the saddle-type filler was the largest. The pressure drop according to the change in air flow rate was measured for the three types of fillers in the scrubbing layer. As a result, the pressure drop was the smallest in the scrubbing layer with the saddle-type filler which has the largest porosity. In addition, the effect of spraying water flowing counter flow against air flow is experimentally examined. It is known that the pressure drop is increased because the air flow space is reduced when water is sprayed. In the case of the saddle, the pressure drop is about 1.5 to 2 times greater than that when only air flows at the optimum exhaust gas-water injection ratio.

• Resources Recycling
• /
• v.17 no.5
• /
• pp.28-36
• /
• 2008

The effect of attrition scrubbing on the recovery of platinum group metals (PGMs) from automobile catalytic converters has been investigated. Catalytic converters were first crushed into particles less than 2 mm and attrition scrubbed in the range of 60 min, and then they were sieved with several screens. The catalyst layer, $\gamma$-alumina, was dislodged from the surface of the supporting matrix into fine particles less than $45{\mu}m$ by attrition scrubbing. The fraction of fine particles less than $45{\mu}m$ increased as the residence time for attrition scrubbing increased. The composition of the fine fraction obtained at a residence time of 40 min was $CeO_2$ 19.3%, $ZrO_2$ 1.9% and PGMs 419 ppm. In the fine fraction, the recovery of y-alumina increased proportionally to the residence time. Simultaneously, the recovery rates of $CeO_2$, $ZrO_2$ and PGMs increased to 82.9%, 78.7% and 78.9%, respectively. The production of the fine fraction less than $45{\mu}m$ and the recovery of $\gamma$-alumina increased when the solid concentration and initial feed size increased. Therefore, the attrition scrubbing as the comminution and separation process was concerned to be effective for the recovery of catalyst layer from ceramic supporting matrix by physical impact and shearing action between particles in the scrubbing vessel.

• Korean Chemical Engineering Research
• /
• v.53 no.2
• /
• pp.137-144
• /
• 2015

The present paper deals with the extractive separation and selective recovery of nickel and lithium from the sulfate leachate of cathode scrap generated during the manufacture of LIBs. The conditions for extraction, scrubbing and stripping of nickel from lithium were optimized with an aqueous feed containing $2.54kg{\cdot}m^{-3}$ Ni and $4.82kg{\cdot}m^{-3}$ Li using PC-88A. Over 99.6% nickel was extracted with $0.15kmol{\cdot}m^{-3}$ PC-88A in two counter-current stages at O/A=1 and pH=6.5. Effective scrubbing Li from loaded organic was systematically studied with a dilute $Na_2CO_3$ solution ($0.10kmol{\cdot}m^{-3}$). The McCabe-Thiele diagram suggests two counter-current scrubbing stages are required at O/A=2/3 to yield lithium-scrubbing efficiency of 99.6%. The proposed process showed advantages of simplicity, and high purity (99.9%) nickel sulfate recovery along with lithium to ensure the complete recycling of the waste from LIBs manufacturing process.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2011.10a
• /
• pp.701-704
• /
• 2011

The reliability of a computer system largely depends on that of its memory systems, which are vulnerable to soft errors. Soft errors can be coped with a combination of an Error Detection & Correction circuit and scrubbing operation. Smaller geometries and lower voltage of advanced memories makes them more prone to suffer multibit soft errors. A memory structure against multibit soft errors and a suitable scrubbing scheme for it were proposed. This paper introduces a key issue for the scrubbing of the memories with protection against multibit soft errors and the result of the performance analysis from a reliability point of view.

• Journal of ILASS-Korea
• /
• v.24 no.1
• /
• pp.8-14
• /
• 2019

The purpose of this study is to develop a packing-free wet scrubber to prolong the maintenance interval compared with the conventional packed bed wet scrubbers with which frequent operation stops are unavoidable to clean the packing materials. The main- and interaction-effects were quantitatively analyzed by regression analysis for the measured ammonia scrubbing data from the experiments prepared by experimental design. The scrubbing efficiency of the newly developed wet scrubber was found to be over 95% under the condition of flue gas flow rate of 90CMM and liquid-to-gas ratio $2l/m^3$ for all considered trials of experimental design. The interaction effect between the inlet duct spray and the filter was found to be important, which controls the droplet growth due to the droplet collisions between the duct- and scrubbing tower-spray. The presented methodology to analyze the impacts of operational and design factors on the scrubber efficiency showed potential for applications to optimize the future flue gas abatement process in semiconductor plants.