• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.18 no.6
• /
• pp.550-553
• /
• 2005

[ $Pb(Zr_{0.2}Ti_{0.8})O_3$ ] powders, prepared by the sol-gel method, were mixed with an organic vehicle and the PZT thick films were fabricated by the screen-printing techniques on Pt/alumina substrates. The structural and dielectric properties were examined as a function of sintering temperature. The particle size distribution of the powder is bimodal with the mean particle size of about $1.2\;{\mu}m$. The average grain size of the PZT thick films sintered above $1000^{\circ}C$ was about $3.1\;{\mu}m$ and the thickness of the specimens was approximately $41\;{\mu}m$. The relative dielectric constant and dielectric loss of the thick films sintered at $1050^{\circ}C$ were 337 and $1.24\%$, respectively.

• Korean Journal of Optics and Photonics
• /
• v.26 no.5
• /
• pp.265-268
• /
• 2015

An inorganic electroluminescence device based on a green ZnS:(Cu,Al) phosphor was fabricated by a screen printing method. Graphene was added to the phosphor layer to increase the electroluminescence intensity. As the graphene concentration increased, the photoluminescence intensity decreased; on the other hand, the electroluminescence intensity increased, up to 0.6 wt%.

• Proceedings of the Korean Powder Metallurgy Institute Conference
• /
• 2006.09a
• /
• pp.430-431
• /
• 2006

Thermoelectric thick film was fabricated by screen printing process with using p-type Bi-Te-Sb powders. The powder was synthesized by melting, milling and sintering process and hydrogen reduced to enhance the thermoelectric property. The thick film of Bi-Te-Sb powder was fabricated by screen printing method and baked at the optimized conditions. The thermal conductivity, the electrical resistivity and Seeback coefficient of thick film were measured and the thermoelectric performance was analyzed in terms of film characteristics and its microstructure. Finally, the feasibility of thermoelectric thick film into micro cooling device on CPU chip was discussed in this study.

• Korean Journal of Materials Research
• /
• v.29 no.4
• /
• pp.228-232
• /
• 2019

Copper electroplating and electrode patterning using a screen printer are applied instead of lithography for heterostructure with intrinsic thin layer(HIT) silicon solar cells. Samples are patterned on an indium tin oxide(ITO) layer using polymer resist printing. After polymer resist patterning, a Ni seed layer is deposited by sputtering. A Cu electrode is electroplated in a Cu bath consisting of $Cu_2SO_4$ and $H_2SO_4$ at a current density of $10mA/cm^2$. Copper electroplating electrodes using a screen printer are successfully implemented to a line width of about $80{\mu}m$. The contact resistance of the copper electrode is $0.89m{\Omega}{\cdot}cm^2$, measured using the transmission line method(TLM), and the sheet resistance of the copper electrode and ITO are $1{\Omega}/{\square}$ and $40{\Omega}/{\square}$, respectively. In this paper, a screen printer is used to form a solar cell electrode pattern, and a copper electrode is formed by electroplating instead of using a silver electrode to fabricate an efficient solar cell electrode at low cost.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.11a
• /
• pp.167-167
• /
• 2008

The barium strontium calcium titanate powders were prepared by sol-gel method. Ferroelectric $(Ba_{0.54}Sr_{0.36}Ca_{0.1})TiO_3$(BSCT) thick films were fabricated by the screen-printing method on alumina substrate. And we investigated the structural and dielectric properties of BSCT thick films with the variation of sintering temperature. As a result of thermal analysis, BSCT polycrystalline perovskite phase was formed at around $660^{\circ}C$. The results of X-ray diffraction analysis were showed a cubic perovskite structure without presence of the second phase in all BSCT thick films. The average grain size and the thickness of the specimen sintered at $1450^{\circ}C$ were about 1.6 mm and 45 mm, respectively. The relative dielectric constant increased and the dielectric loss decreased with increasing the sintering temperature, the values of the BSCT thick films sintered at $1450^{\circ}C$ were 5641 and 0.4% at 1kHz, respectively.

• 한국초전도학회:학술대회논문집
• /
• v.15
• /
• pp.99-99
• /
• 2005

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.25 no.12
• /
• pp.1015-1020
• /
• 2012

Resistance of the front electrode is the highest proportion of the ingredients of the series resistance in crystalline silicon solar cell. While resistance of the front electrode is decreased with larger area, it induces the optical loss, causing the conversion efficiency drop. Therefore the front electrode with high aspect ratio increasing its height and decreasing is necessary for high-efficiency solar cell in considering shadowing loss and resistance of front electrode. In this paper, we used the screen printing method to form high aspect ratio electrode by multiple printing. Screen printing is the straightforward technology to establish the electrodes in silicon solar cell fabrication. The several printed front electrodes with Ag paste on silicon wafer showed the significantly increased height and slightly widen finger. As a result, the resistance of the front electrode was decreased with multiple printing even if it slightly increased the shadowing loss. We showed the improved electrical characteristics for c-Si solar cell with repeatedly printed front electrode by 0.5%. It lays a foundation for high efficiency solar cell with high aspect ratio electrode using screen printing.

• Proceedings of the KSME Conference
• /
• 2008.11a
• /
• pp.1087-1090
• /
• 2008

This paper presents the electro-luminescence (EL) display lamp which is patterned on a curved surface by the pad printing method. The printing methods, including the gravure, screen, flexo, inkjet, and pad printing, have an advantage of one-step direct patterning. However, in general, the printing and semi-conductor process, except pad printing method, cannot be applied for patterning on a curved surface. Thus, in this paper, we used pad printing method for patterning an EL display lamp on a curved surface. The EL display lamp consists of 5 layers: Bottom electrode; Dielectric layer; Phosphor; Transparent electrode; Bus electrode. Finally, we printed EL display lamp on a dish, which has a radius of curvature 80mm. The EL display lamp was driven at AC 200V of 1kHz.

• Journal of the Korean Graphic Arts Communication Society
• /
• v.15 no.2
• /
• pp.57-76
• /
• 1997

A color halftoning is the process of generating halftone images for the different color plans, for example, cyan, magenta, yellow, and black for a offset printing device. A conventional halftone technique, so called AM screening, is simple and easy to implement, but the halftoned dot patterns by using this method is not free for the moire` fringe. Moire` patterns are caused the power spectrum distribution on low spatial frequency domain. To avoid Moire` patterns, the conventional screen require the different screen angles for each color plans. Recently, Ultra-fine and 7 color printing methods are developed to expend the color gamut. In 7 color printing method must be used the halftone technique of random and blue noise characteristic to avoid Moire` fringe.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.20 no.6
• /
• pp.272-277
• /
• 2019

In this paper, a manufacturing method of an anti-glare cover glass on LCD for outdoor use is proposed. The main specification of cover glass is hardness and anti-glare. Hardness is achieved by using the tempered glass, and anti-glare(AG) film is laminated to meet anti-glare specification no the tempered glass. However, the AG film is difficult to maintain the AG performance continuously because the abrasion resistance of the PET film itself is as weak as about 3H. Therefore, a novel production procedure using screen printing method is proposed. The proposed coating is implemented by applying $ZnO-B_2O_3-SiO_2$ powder on glass surface and the glass is made with enhanced hardness through tempering process. In order to apply the ZBS powder uniformly on the glass surface, a screen printing process is used. The main parameters to be considered in screen printing are the oil concentration and mesh opening size. Because the amount of ZBS powder applied to the printing process is controlled by these two parameters, the correlativity is confirmed through the experiments. In order to evaluate the performance of the proposed method, the haze, surface roughness and transmittance are selected as the performance index and are compared with the AG film. As a result of comparison, it is verified that the transmittance of the proposed tempered glass is 83.1%, which is slightly lower than 89.5% of AG film, but the hardness is more than double to 7H.