• Journal of the Korea Society for Simulation
• /
• v.25 no.2
• /
• pp.21-29
• /
• 2016

Indoor location system has been used Wi-Fi to get a location. After the development of BLE(Bluetooth Low Energy), the interest in the method of a indoor positioning had been move on. It has more advantages than using Wi-Fi. Easy installation, low power consumption, low signal interference and changeable setting(Advertising interval, tx power, etc.). These things can improve efficiency or accuracy in a indoor positioning system. For this reason, recent indoor positioning system uses BLE rather than Wi-Fi. Accordingly, error factors of BLE beacon based indoor positioning should be studying for high accuracy of indoor positioning. In this research, set up few experiment scenarios and keep a close watch on how technological, environmental factor is affecting positioning accuracy. When a application uses largest signal strength to get the indoor location, the mean error of experimental results was decreased compare to using received signal strength in real-time. The result was same when the application applied average and standard deviation to get the indoor location. Changing advertising interval had an effect on the mean error of indoor positioning. Short advertising interval makes the lower mean error than large advertising interval.

• Korean Journal of Materials Research
• /
• v.11 no.8
• /
• pp.671-678
• /
• 2001

All solid-state thin film micro supercapacitor, which consists of $RuO_2$/LiPON/$RuO_2$ multi layer structure, was fabricated on Pt/Ti/Si substrate using a $RuO_2$ electrode. Bottom $RuO_2$ electrode was grown by dc reactive sputtering system with increasing $O_2/[Ar+O_2]$ ratio at room temperature, and a LiPON electrolyte film was subsequently deposited on the bottom $RuO_2$ electrode at pure nitrogen ambient by rf reactive sputtering system. Room temperature charge-discharge measurements based on a symmetric $RuO_2$/LiPON/$RuO_2$ structure clearly demonstrates the cyclibility dependence on the microstructure of the $RuO_2$ electrode. Using both glancing angle x-ray diffraction (GXRD) and transmission electron microscopy (TEM) analysis, it was found that the microstructure of the $RuO_2$ electrode was dependent on the oxygen flow ratio. In addition, x- ray photoelectron spectroscopy(XPS) examination shows that the Ru-O binding energy is affected by increasing oxygen flow ratio. Furthermore, TEM and AES depth profile analysis after cycling demonstrates that the interface layer formed by interfacial reaction between LiPON and $RuO_2$ act as a main factor in the degradation of the cyclibility of the thin film micro-supercapacitor.

• Journal of the Korea Convergence Society
• /
• v.6 no.6
• /
• pp.293-299
• /
• 2015

MOOC (Massive Open Online Course) is an online course aimed at limited participation and open access via the web. There is even the prospect that MOOC may break down the existing university system and open a new horizon of education. However, MOOC is going differently from the first prospect that it would threat the existing higher education institutions. So this study wishes to provide a starting point of discussion that we can produce and utilize MOOC to fit our situation of higher education by revealing the inherent problems of MOOC. MOOC is a basically online education, so that it cannot help inheriting the essential weakness of the existing one: the interaction, supervision and evaluation. The newly added concept 'massive' raises the problem of class size which is the most sensitive part in the field of education. The concept 'open' reverses a customized education because MOOC is a kind of video clips of a lecture for unspecific massive learners. As a conclusion, we predicts that MOOC will be positioned as a higher education service for very prominent learners in self-led learning ability and people who cannot access even traditional online higher education institutions. Also MOOC is highly likely to be used as a means of Flipped Learning in universities. Therefore, considering these points in the future, we need to develop MOOC to suit these targets.

• Genomics & Informatics
• /
• v.16 no.2
• /
• pp.22-29
• /
• 2018

Incorporation of unique barcodes into fission yeast gene deletion collections has enabled the identification of gene functions by growth fitness analysis. For fine tuning, it is important to examine barcode sequences, because mutations arise during strain construction. Out of 8,708 barcodes (4,354 strains) covering 88.5% of all 4,919 open reading frames, 7,734 barcodes (88.8%) were validated as high-fidelity to be inserted at the correct positions by Sanger sequencing. Sequence examination of the 7,734 high-fidelity barcodes revealed that 1,039 barcodes (13.4%) deviated from the original design. In total, 1,284 mutations (mutation rate of 16.6%) exist within the 1,039 mutated barcodes, which is comparable to budding yeast (18%). When the type of mutation was considered, substitutions accounted for 845 mutations (10.9%), deletions accounted for 319 mutations (4.1%), and insertions accounted for 121 mutations (1.6%). Peculiarly, the frequency of substitutions (67.6%) was unexpectedly higher than in budding yeast (~28%) and well above the predicted error of Sanger sequencing (~2%), which might have arisen during the solid-phase oligonucleotide synthesis and PCR amplification of the barcodes during strain construction. When the mutation rate was analyzed by position within 20-mer barcodes using the 1,284 mutations from the 7,734 sequenced barcodes, there was no significant difference between up-tags and down-tags at a given position. The mutation frequency at a given position was similar at most positions, ranging from 0.4% (32/7,734) to 1.1% (82/7,734), except at position 1, which was highest (3.1%), as in budding yeast. Together, well-defined barcode sequences, combined with the next-generation sequencing platform, promise to make the fission yeast gene deletion library a powerful tool for understanding gene function.

• Korean Journal of Microbiology
• /
• v.45 no.2
• /
• pp.140-147
• /
• 2009

In this study, anaerobic enrichment cultivation was performed with the sediments from the Gimpo and Inchon areas. Lactate as an electron donor and PCE as an electron acceptor was injected into the serum bottle with an anaerobic medium. After the incubation of 8 weeks, the reductive dechlorination of PCE was observed in 7 sites among 16 sites (43%). Three enrichment cultures showed completely dechlorination of PCE to ethene, while four enrichment culture showed transformation of PCE to cis-DCE. The bacterial community structure was analyzed by PCR-DGGE. Dechlorinating bacteria were detected by species-specific primers. The dominant species in seven anaerobic enrichments were found to belong to the genus of Dehalococcoides sp. and Geobacter sp., and Dehalobacter sp.

• Journal of the Korean Electrochemical Society
• /
• v.14 no.3
• /
• pp.131-137
• /
• 2011

A simple and rapid electrochemical method for the quantitative analysis of $Mn^{2+}$ ion is demonstrated with a view to examine the $Mn^{2+}$ dissolution behavior of $LiMn_2O_4$. The method described herein is based on the oxidation reaction of $Mn^{2+}$ to $Mn^{4+}(MnO_2)$ in aqueous buffer solution. Under the optimum condition (pH 8.9 0.04 M $NH_3-NH_4Cl$ buffer solution and glassy carbon working electrode), the linear range of $5{\mu}M-100{\mu}M$ (0.275-5.5 ppm) [$Mn^{2+}$] is obtained for the Linear sweep voltammetry(LSV) and $0.2{\mu}M-10{\mu}M$ (0.011-0.55 ppm) [$Mn^{2+}$] for the differential pulse voltammetry (DPV), respectively. It is also noted that the oxidation reaction of $Mn^{2+}$ ion is reduced with increasing amount of the electrolyte ($LiPF_6$, EC, EMC) added to the measuring solution, which is found to be mainly due to $LiPF_6$ and EC rather than EMC.

• Journal of Korean Society of Environmental Engineers
• /
• v.39 no.6
• /
• pp.325-331
• /
• 2017

Adsorption experiments of carbon dioxide were performed on ZSM5 and Molecular Sieve 13X (MS13X) impregnated with Monoethanol Amine (MEA). Adsorption efficiency of $CO_2$ was investigated in a U type packed column with GC/TCD. The adsorption capacities of adsorbents are estimated in the temperature range of $30-80^{\circ}C$. The modified adsorbents was characterized by BET surface area, $N_2$ adsorption/desorption isotherms, X-ray diffraction and FT-IR. Surface analysis results showed that the impregnation method did not affect the crystallinity of any adsorbents. BET surface area of the MS13X impregnated amine decreased to $19.945m^2/g$ from $718.335m^2/g$. These reults showed that amine molecules were filled with the pore volume in MS13X, as a results restricting access of nitrogen into the pores. The MEA modified MS13X showed improvement in $CO_2$ adsorption capacity over the ZSM5 impregnated with MEA. The MS13X-MEA showed the highest adsorption capacity due to physical adsorption and chemical adsorption by amino-group content. This results also showed that adsorption capacity of MS13X-MEA increases with the temperature range of $60-80^{\circ}C$ compared with pristine MS13X.

• The Korean Journal of Mycology
• /
• v.25 no.3 s.82
• /
• pp.209-218
• /
• 1997

This study was carried out to obtain the basic data for artificial culture of Grifola umbellata. The optimal condition for the mycelial growth was obtained at $20^{\circ}C$ and pH 4, respectively. G. umbellata showed the most favorable growth on the Hoppkins media. Carbon sources such as glucose, fluctose and manitol were favorable for stimulating a mycelial growth of G. umbellata. Valine, one of nitrogen sources also appeared to be favorable to a mycelial growth. The optimum C/N ratio was about 30:1 in case that 1% glucose as carbon source was mixed with the basal media. Lactic acid as organic acid was most favorable to the mycelial growth. Also, thiamine-Hcl as vitamin source was favorable. The mineral nutrient of $FeSO_4$ or $MgSO_4$ was most favorable to G. umbellata, and its optimal concentration was about 0.01% in $FeSO_4$ and 0.1 % in $MgSO_4$ respectively. Among 4 different cereal extract media, polished rice extract medium which was mixed with silkworm pupae was most suitable for a favorable growth of G. umbellata.

• Journal of Broadcast Engineering
• /
• v.18 no.5
• /
• pp.758-770
• /
• 2013

In a Broadcast Encryption System, a sender sends an encrypted message to a large set of receivers at once over an insecure channel and it enables only users in a target set to decrypt the message with their private keys. In 2005, Boneh et al. proposed a fully collusion-resistant public key broadcast encryption in which the ciphertext and the privatekey sizes are constant. In general, pairing-based broadcast encryption system is efficient in bandwidth and storing aspects than non-pairing based broadcast encryption system, however, it requires many computational costs that resource-constrained devices is not suit to be applied. In this paper, we propose a Broadcast Encryption scheme(called BEWD) that user can decrypt a ciphertext more efficiently. The scheme is based on Boneh et al.scheme. More precisely, it reduces receiver's computational costs by delegating pairing computation to a proxy server which computation is required to receiver in Boneh et al.scheme. Furthermore, the scheme enables a user to check if the proxy server compute correctly. We show that our scheme is secure against selective IND-RCCA adversaries under l-BDHE assumption.

• Journal of Internet Computing and Services
• /
• v.16 no.2
• /
• pp.19-26
• /
• 2015

Operating on its own to develop a system or based on the standard to setup and operating of RFID System. If you want to operate RFID system yourself then It is no problem to use its own to develop a system, but have to implementation RFID System based standard for the system integration and data linkage in multiple companies or base. In this paper, I propose an EPCIS Capturing Application of the element for applying an RFID-based EPC Network as an international civil standards organization EPCglobal. EPCIS Capturing Application generation is a message for transmission to EPCIS receives the data transmitted from the reader and middleware to serve to transfer the EPCIS. This paper also proposes Capture Interface capable of receiving the data of the equipment does not use the ALE Interface as a portable RFID reader ALE Interface, as well as used by the RFID reader to implement a fixed system for use in the field. In this paper, we propose a EPCIS Capturing Application for tracking the history RFID is applied to the finished product. It is possible to take advantage to be applied to all systems based on the EPCglobal standard through proposed the EPCIS Capturing Application.