• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.8 no.4
• /
• pp.640-644
• /
• 1998

We have fabricated Sb/SiC(4H) Schottky barrier diode (SBD) of which characteristics compared with that of Ti/SiC(4H) SBD. The donor concentration of the n-type SiC(4H) obtained by capacitance-voltage (C-V) measurement was about $2.5{\times}10 ^{17}{\textrm}cm^{-3}$. The ideality factors of 1.31 was obtained from the slope of forward current-voltage (I-V) characteristics of Sb/SiC(4H) SBD at low current density. The breakdown field of Sb/SiC(4H) SBD under the reverse bias voltage was about $4.4{\times}10^2V$/cm. The built-in potential and the Schottky barrier height (SBH) of Sb/SiC(4H) SBD were 1.70V and 1.82V, respectively, which were determined by the analysis of C-V characteristics. The Sb/SiC(4H) SBH of 1.82V was higher than Ti/SiC(4H) SBH of 0.91V. However, the current density and reverse breakdown field of Sb/SiC(4H) were low as compared with those of Ti/SiC(4H). The Sb/SiC(4H), as well as the Ti/SiC(4H), can be utilized as the Shottky barrier contact for the high-power electronic device.

• Journal of Sensor Science and Technology
• /
• v.14 no.2
• /
• pp.96-100
• /
• 2005

The planar Schottky diodes were fabricated and modeled to probe the device applicability of the cracked GaN epitaxial layer on a (111) silicon substrate. On the unintentionally n-doped GaN grown on silicon, we deposited Ti/Al/Ni/Au as the ohmic metal and Pt as the Schottky metal. The ohmic contact achieved a minimum contact resistivity of $5.51{\times}10.5{\Omega}{\cdot}cm^{2}$ after annealing in an $N_{2}$ ambient at $700^{\circ}C$ for 30 sec. The fabricated Schottky diode exhibited the barrier height of 0.7 eV and the ideality factor was 2.4, which are significantly lower than those parameters of crack free one. But in photoresponse measurement, the diode showed the peak responsivity of 0.097 A/W at 300 nm, the cutoff at 360 nm, and UV/visible rejection ratio of about $10^{2}$. The SPICE(Simulation Program with Integrated Circuit Emphasis) simulation with a proposed model, which was composed with one Pt/GaN diode and three parasitic diodes, showed good agreement with the experiment.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.28 no.6
• /
• pp.371-374
• /
• 2015

This paper suggests a high performance lateral super barrier rectifier (Lateral SBR) device which has the advantages of both Schottky diode and pn junction, that is, low forward voltage and low leakage current, respectively. Advantage of the proposed lateral SBR is that it can be easily implemented and integrated in current BCD platform. As a result of simulation using TCAD, BVdss = 48 V, $V_F=0.38V$ @ $I_F=35mA$, T_j = $150^{\circ}C$ were obtained with very low leakage current characteristic of 3.25 uA.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.5 no.1
• /
• pp.157-165
• /
• 2001

We analyzed the electrical characteristics of platinum silicide schottky junction to develope the voltage swing in Integrated Schottky Logic gates, and simulated the characteristics with the programs in this junctions. Simulation programs for analytic characteristics are the Medichi tool for device structure, Matlab for modeling and SUPREM V for fabrication process. The silicide junctions consist of PtSi and variable silicon substrate concentrations in ISL gates. Input parameters for simulation characteristics were the same conditions as process steps of the device farications process. The analitic electrical characteristics were the turn-on voltage, saturation current, ideality factor in forward bias, and has shown the results of breakdown voltage between actual characteristics and simulation characteristics in reverse bias. As a result, the forward turn-on voltage, reverse breakdown voltage, barrier height were decreased but saturation current and ideality factor were increased by substrates increased concentration variations.

• Journal of Korea Multimedia Society
• /
• v.3 no.5
• /
• pp.535-541
• /
• 2000

In this paper, we analyzed the characteristics of schottky junction to develop the voltage swing of ISL, and simulated the characteristics with the programs at this junctions. Simulation programs for analytic characteristics are the SUPREM V, SPICE, Medichi, Matlab. The schottky junction is rectifier contact between platinum silicide and silicon, the characteristics with programs has simulated the same conditions. The analytic parameters were the turn-on voltage, saturation current, ideality factor in forward bias, and has shown the results of breakdown voltage between actual characteristics and simulation characteristics in reverse bias. As a result, th forward turn-on voltage, reverse breakdown voltage, barrier height were decreased but saturation current and ideality factor were increased by substrates increased concentration variations.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2012.02a
• /
• pp.386-386
• /
• 2012

We studied a bilateral switching device for spin transfer torque (STT-MRAM) based on 3D device simulation. Metal/P/N+or Metal/N/P+ junction device with $30{\times}30nm2$ area which is composed of one side schottky junction at Metal/P/N+ and Metal/N/P+ provides sufficient bidirectional current flow to write data by a drain induced barrier lowering (DIBL). In this work, Junction device confirmed that write current is more than 30 uA at 2 V, It is also has high on-off ratio over 105 under read operation. Junction device has good process feasibility because metal material of junction device could have been replaced by bottom layer of MTJ. Therefore, additional process to fabricate two outer terminals is not need. so, it provides simple fabrication procedures. it is expected that Metal/P/N+ or Metal/N/P+ structure with one side schottky junction will be a promising switch device for beyond 30 nm STT-MRAM.

• Electrical & Electronic Materials
• /
• v.9 no.7
• /
• pp.708-718
• /
• 1996

The microstructure and electrical properties of the nonlinear ZnO varistor with A1$_{2}$ $O_{3}$ additions is investigated. The variation of nonlinear behavior with A1$_{2}$ $O_{3}$ additions is indicated from J-E and C-V measurement to be a result of the change of the interface defects density $N_{t}$ at the grain boundaries and the donor concentration $N_{d}$ in the ZnO grains. The optimum composition which has the nonlinear coefficients of -57 was observed in the sample with 0.005wt% A1$_{2}$ $O_{3}$ additions. The conduction mechanism at the pre-breakdown region is consistent with a Schottky thermal emission process obeying a relation given by $J^{\var}$exp[-(.psi.-.betha. $E^{1}$2/)kT] and the conduction process at the breakdown region follows a Fowler-Nordheim tunneling mechanism of the form $J^{\var}$exp(-.gamma./E).

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2004.07a
• /
• pp.409-412
• /
• 2004

Edge termination technique is essential fer the fabrication of high volage devices. A proper edge termination technique is also needed in the fabrication of Silicon Carbide power devices for obtaining a stable high blocking voltage properties. Among the many techniques, the field plate formation is the easiest one that can utilize it for commercial usage. The growth of thick thermal oxide is difficult for SiC, however. In this paper, 6A grade SiC schottky barrier diodes(SBD) were fabricated with field plate edge termination. The oxides which is field plate were formed various methods such as dry oxidation, 10% $N_2O$ nitrided oxidation and PECVD deposition. The reverse characteristics of the SiC SBD with various oxide field plate were investigated.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2005.07a
• /
• pp.191-192
• /
• 2005

The reverse breakdown voltages of 4H-SiC SBD(schottky barrier diode)s with FP(Field Plate) and/or FLR(Field Limiting Ring) as a edge termination, were investigated. The breakdown voltages of SBDs with FP ware investigated varying the overlap width from $1{\mu}m$ to $30{\mu}m$. The maximum average breakdown voltages was 475V. There is no significant changes for the devices with overlap width of between $5{\mu}m\sim30{\mu}m$. It was confirmed that the dielectric breakdown of the thin thermal oxide is main cause of device failure. However, the breakdown voltage of SBD with FLR was 1400V even though the FLR edge termination structure was not optimized.

• Advances in nano research
• /
• v.10 no.4
• /
• pp.339-347
• /
• 2021

In the framework of the density functional theory combined with the method of non-equilibrium Green functions (DFT + NEGF), the electric transport properties of a one-dimensional nanodevice consisting of telescoping polyprismanes with various types of electrical conductivity were studied. Its transmission spectra, density of state, current-voltage characteristic, and differential conductivity are determined. It was shown that C_[14,17], C_[14,11], C_[14,16], C_[14,10] show a metallic nature, and polyprismanes C_[14,5], C_[14,4] possess semiconductor properties and has a band gap of 0.4 eV and 0.6 eV, respectively. It was found that, when metal C_[14,11], C_[14,10] and semiconductor C_[14,5], C_[14,4] polyprismanes are coaxially connected, a Schottky barrier is formed and a weak diode effect is observed, i.e., manifested valve (rectifying) property of telescoping polyprismanes. The enhancement of this effect occurs in the nanodevices C_[14,17] - C_[14,11] - C_[14,5] and C_[14,16] - C_[14,10] - C_[14,4], which have the properties of nanodiode and back nanodiode, respectively. The simulation results can be useful in creating promising active one-dimensional elements of nanoelectronics.