• 한국재료학회지
• /
• 제28권4호
• /
• pp.235-240
• /
• 2018

We propose a speedy two-step deposit process to form an Au electrode on hole transport layer(HTL) without any damage using a general thermal evaporator in a perovskite solar cell(PSC). An Au electrode with a thickness of 70 nm was prepared with one-step and two-step processes using a general thermal evaporator with a 30 cm source-substrate distance and $6.0{\times}10^{-6}$ torr vacuum. The one-step process deposits the Au film with the desirable thickness through a source power of 60 and 100 W at a time. The two-step process deposits a 7 nm-thick buffer layer with source power of 60, 70, and 80 W, and then deposits the remaining film thickness at higher source power of 80, 90, and 100 W. The photovoltaic properties and microstructure of these PSC devices with a glass/FTO/$TiO_2$/perovskite/HTL/Au electrode were measured by a solar simulator and field emission scanning electron microscope. The one-step process showed a low depo-temperature of $88.5^{\circ}C$ with a long deposition time of 90 minutes at 60 W. It showed a high depo-temperature of $135.4^{\circ}C$ with a short deposition time of 8 minutes at 100 W. All the samples showed an ECE lower than 2.8 % due to damage on the HTL. The two-step process offered an ECE higher than 6.25 % without HTL damage through a deposition temperature lower than $88^{\circ}C$ and a short deposition time within 20 minutes in general. Therefore, the proposed two-step process is favorable to produce an Au electrode layer for the PSC device with a general thermal evaporator.

• 한국재료학회지
• /
• 제28권4호
• /
• pp.214-220
• /
• 2018

We report on the fabrication and photoelectrochemical(PEC) properties of a $Cu_2O$ thin film/ZnO nanorod array oxide p-n heterojunction structure with ZnO nanorods embedded in $Cu_2O$ thin film as an efficient photoelectrode for solar-driven water splitting. A vertically oriented n-type ZnO nanorod array was first prepared on an indium-tin-oxide-coated glass substrate via a seed-mediated hydrothermal synthesis method and then a p-type $Cu_2O$ thin film was directly electrodeposited onto the vertically oriented ZnO nanorods array to form an oxide semiconductor heterostructure. The crystalline phases and morphologies of the heterojunction materials were characterized using X-ray diffraction and scanning electron microscopy as well as Raman scattering. The PEC properties of the fabricated $Cu_2O/ZnO$ p-n heterojunction photoelectrode were evaluated by photocurrent conversion efficiency measurements under white light illumination. From the observed PEC current density versus voltage (J-V) behavior, the $Cu_2O/ZnO$ photoelectrode was found to exhibit a negligible dark current and high photocurrent density, e.g., $0.77mA/cm^2$ at 0.5 V vs $Hg/HgCl_2$ in a $1mM\;Na_2SO_4$ electrolyte, revealing an effective operation of the oxide heterostructure. In particular, a significant PEC performance was observed even at an applied bias of 0 V vs $Hg/HgCl_2$, which made the device self-powered. The observed PEC performance was attributed to some synergistic effect of the p-n bilayer heterostructure on the formation of a built-in potential, including the light absorption and separation processes of photoinduced charge carriers.

• 한국산학기술학회논문지
• /
• 제12권5호
• /
• pp.2011-2018
• /
• 2011

본 논문에서는 공조용 로타리 컴프레서에서 발생하는 소음을 줄이기 위하여 음향 홀로그래피를 이용하는 방법을 다룬다. 소음이 방사되는 것을 음향 홀로그래피를 이용하여 정상적인 컴프레서와 문제가 있는 컴프레서에 대하여 측정하였다. 음향 홀로그램은 2가지 컴프레서의 다수의 격자점에서 측정 및 예측하였고, 컴프레서 표면 위로 재구성하였다. 2개의 마이크로폰을 사용하여 1344개의 측정 점에서 측정을 수행하였고, 그 중 1개의 마이크로폰은 스캐닝용이고 또 다른 하나의 마이크로폰은 레퍼런스용이다. 음향 홀로그래피는 소음원을 그래픽적으로 보여주기 위한 좋은 도구이다. 본 논문에서 컴프레서의 표면에서 소음 원 위치를 정확히 찾을 수 있었고, 그 소음원은 소음을 발생시키는 부품과 관계된 것이었다. 음향 홀로그래피는 가전제품에 대해 소음 저감 방법으로서 유용함을 알 수 있다.

• 조명전기설비학회논문지
• /
• 제16권1호
• /
• pp.13-19
• /
• 2002

새로운 방전 AND gate를 가지는 플라즈마 디스플레이 패널이 제안되었고 이를 검증하기 위한 구동 회로 시스템이 개발되었다. 그리고 방전 AND gate의 동작이 검증되었다. 방전 AND gate는 8$\mu\textrm{s}$의 동작속도와 20V의 동작마진을 가지고 동작하였으며 인근 주사라인의 방전을 정확히 제어할 수 있다는 것을 알았다. 이 방식은 직류 방전을 사용함으로 종래의 방전 AND gate에 비해 손쉽게 방전을 제어할 수가 있다. 더구나 AND gate의 입력방전과 출력방전이 분리되어 동작하기 때문에 디스플레이 방전이 AND gate를 통과하는 것을 방지할 수 있다. 그러므로 대화면 플라즈마 디스플레이에의 적용이 가능하고 주사방전이 화질에 영향을 주지 않으므로 명암비의 저하가 일어나지 않는다.

• Journal of Pharmaceutical Investigation
• /
• 제33권3호
• /
• pp.179-185
• /
• 2003

Melatonin (MT) is an indole amide pineal hormone. It has not only very short half-life but also pH-sensitive property. The sustained release dosage form which delivers MT in a circadian fashion over 8 h is clinical value. The purpose of this study is to prepare sugar beads using multiple coating methods and enteric-coated in a sustained release to evaluate in vitro release characteristics in simulated gastric and intestinal fluids. The $Eudragit^{\circledR}$ as a polymer, sustained release membrane, and triethylcitrate (TEC) as a plasticzer were used. Multi-coated melatonin delivery system was composed of sugar, various excipients, $Eudragit^{\circledR}$ and enteric materials (e.g. hydroxy propyl methyl cellulose phthalate, HPMCP), and prepared by fluid bed coater. The dissolution test was carried out using the basket method at a stirring speed of 100 rpm at $37^{\circ}C$ in simulated gastric (pH 1.2) and intestinal fluid (pH 7.4). The released amount of MT was determined by High performance liquid chromatography method. The morhologies of surface and cross section of multi-coated beads were observed by scanning electron microscope. Size of multi-coated sugar beads was ranged over $1000{\sim}1300\;{\mu}m$. The release rate of MT from coated beads was limited in simulated gastric fluid (pH 1.2), but it was sustained in intestinal fluid (pH 7.4) during $3{\sim}8$ hours. The MT beads may provide small-intestine-targeted device for oral delivery. Studies on animal and relative experiment are in process.

• 한국해양공학회지
• /
• 제25권4호
• /
• pp.66-71
• /
• 2011

The flexural strength of $MoSi_2$ based composites reinforced with Nb sheets has been investigated, based on the detailed examination of their microstructure and fractured surface. Both sintered density and porosity of Nb/$MoSi_2$ composites were also examined. Nb/$MoSi_2$ composites were fabricated by different conditions such as temperature, applied pressure and its holding time, using a hot-press device. The volume fraction of Nb sheet in this composite system was fixed as 10%. The characterization of Nb/$MoSi_2$ composites were investigated by means of optical microscopy, scanning electron microscope and three point bending test. Nb/$MoSi_2$ composites represented a dense morphology at the interfacial region, accompanying the creation of two types of reaction layer by the chemical reaction of Nb and $MoSi_2$. Nb/$MoSi_2$ composites possessed an excellent density at the fabricating temperature of $1350^{\circ}C$, corresponded to about 95% of theoretical density. The flexural strength of Nb/$MoSi_2$ romposites were greatly affected by the pressure holding time at the same fabricating temperature, owing to the large suppression of porosity in the microstructure. Especially, Nb/$MoSi_2$ composites represented a good flexural strength of about 310 MPa at the fabricating condition of $1350^{\circ}C$, 30MPa and 60min, accompanying the pseudo-ductile fracture behavior by the deformation of Nb sheet and the interfacial delamination.

• 한국전기전자재료학회논문지
• /
• 제24권7호
• /
• pp.537-542
• /
• 2011

Recently, n-InZnO/p-CuO oxide diode has attracted great attention due to possible application for selector device of 3-dimensional cross-point resistive memory structures. To investigate the detailed properties of InZnO (IZO), we have deposited IZO films on the fused quartz substrate using PLD (pulsed laser deposition) method at oxygen pressure of 1~100 mTorr and substrate temperature of RT$\sim600^{\circ}C$. The influence of oxygen pressure and substrate temperature on structural, optical and electrical of IZO films is analyzed using XRD (x-ray diffraction), SEM (scanning electron microscopy), UV-Vis spectrophotometry, spectroscopic ellipsometry (SE) and hall measurements. The XRD results shows that the deposited thin films are polycrystalline over $300^{\circ}C$ of substrate temperature independent of oxygen pressure. The resistivity of films was increased as oxygen pressure and substrate temperature decrease. The thickness and optical constants of the deposited films measured with UV-Vis spectrophotometer were also compared with those of broken SEM and SE results.

• 센서학회지
• /
• 제27권5호
• /
• pp.311-316
• /
• 2018

An antenna-coupled bolometer-type terahertz sensor was designed, fabricated, evaluated, and utilized to obtain terahertz transmission images. The sensor consists of a thin film bowtie antenna that resonates accordingly in response to an incident terahertz beam, a heater that converts the applied current in the antenna into heat, and a microbolometer that converts the rise in temperature into a change in resistance. The device is fabricated by a bulk micromachining process on a 4-inch silicon wafer. The fabricated sensor chip has a size of $2{\times}2mm$ and an active area of $0.1{\times}0.1mm^2$. The temperature coefficient of resistance (TCR) of the bolometer film (VOx) is 2.0%, which is acceptable for bolometer applications. The output sensor signal is proportional to the power of the incident terahertz beam. Transmission images were obtained with a 2-axis scanning imaging system that contained the sensor. The small active area of the sensor will enable the development of highly sensitive focal plane array sensors in terahertz imaging cameras in the future.

• 한국분말재료학회지
• /
• 제9권5호
• /
• pp.359-364
• /
• 2002

We report the structure, thermal and magnetic properties of a non-equilibrium $Al_{0.6}(Fe_{50}Cu_{50})_{0.4}$ alloy powder produced by rod milling and chemical leaching. An X-ray diffractometry(XRD), a transmission electron microscope(TEM), a differential scanning calorimeter(DSC), a vibrating sample magnetometer(VSM), and superconducting quantum interference device(SQUID) were utilized to characterize the as-milled and leaching specimens. The crystallite size reached a value of about 8.82 nm. In the DSC experiment, the peak temperatures and crystallization temperatures decreased with increasing milling time. The activation energy of crystallization is 200.5 kJ/mole for as-milled alloy powder. The intensities of the XRD peaks of as-milled powders associated with the bcc type $Al_{0.5}Fe_{0.5}$ structure formative at $350^{\circ}C$ sharply increase with increasing annealing temperature. Above $400^{\circ}C$, peaks alloted to $Al_{0.5}Fe_{0.5}$ and $Al_{5}Fe_{2}$ are observed. After annealing at $600^{\circ}C$ for 1h, the leached Ll specimen transformed into bcc $\alpha$-Fe and fcc Cu phases, accompanied by a change in the structural and magnetic properties. The saturation magnetization decreased with increasing milling time, and a value of about 8.42 emu/g was reached at 500 h of milling. The coercivity reached a maximum value of about 142.7 Oe after 500 h of milling. The magnetization of leached specimens as function of fields were higher at 5 K, and increased more sharply at 5 K than at 100 K.

• 한국산학기술학회논문지
• /
• 제16권3호
• /
• pp.2131-2134
• /
• 2015

본 논문에서는 종이를 기판으로 사용하고 용액공정이 가능한 강유전체 메모리 소자의 제작 가능성을 검토하였다. 유기물 강유전체인 "폴리비닐리덴트리플루오르에틸렌" 용액을 하부전극이 형성된 종이기판 위에 스핀코핑 방법을 이용하여 도포하였다. 하부전극으로는 진공증착법을 이용하여 알루미늄을 증착하였고, 도포된 "폴리비닐리덴트리플루오르에틸렌" 용액은 열처리 과정을 통해 결정화하였다. 제작된 "폴리비닐리덴트리플루오르에틸렌" 박막은 주사 전자 현미경법(SEM), 원자간력 현미경(AFM)을 이용하여 박막의 단면 및 표면의 특성을 평가하였다. 전압에 따른 분극특성 측정을 통해, 종이기판 위에 형성된 "폴리비닐리덴트리플루오르에틸렌" 박막이 매우 훌륭한 강유전체 특성을 보여주고 있음을 확인하였다. 또한, 종이기판의 응용가능성을 검토하기 위하여, 실리콘 기판위에 제작한 "폴리비닐리덴트리플루오르에틸렌" 박막과의 비교에 있어서도 손색없는 강유전체 특성을 보여주고 있음을 알 수 있었다. 이러한 결과들은 종이를 기판으로 이용하여 전자소자들을 제작 할 수 있음을 시사하며, 또한 용액공정으로 고밀도의 저렴한 강유전체 메모리 소자를 손쉽게 제작 할 수 있다는 것을 의미한다.