• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2010.10a
• /
• pp.537-537
• /
• 2010

High precision sensing is very important in various technologies. Especially, it is more important when it were applied to nano/micro meter level's sensing like AFM, storage, etc. And capacitive sensing is widely used method. To improve the measurement efficiency, many signal conditioners were studied and one of them was surface acoustic wave (SAW) device. SAW device is very widely used as a high frequency bandwidth filter. Due to the reflective characteristic of high frequency, the response of SAW device contains both propagative and reflective signal at the external impedance. In this paper, we used SAW device as signal conditioner of capacitive sensor. And high precision gap measurement was executed using capacitive load. Reference signal was reflective SAW response and the magnitude at the center frequency of SAW device by the change of impedance was checked. Finally, the attainable gap resolution was determined.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.13 no.5
• /
• pp.1030-1037
• /
• 2009

SAW Sensor is greatly developed today and Reader Platform which uses SAW Sensor for temperature or pressure is required to use TDS method for low power and high speed processing. For to use this Platform, high speed timer is required to measure a short interval between reference signal and reflectior's signal. This paper proposes that platform receive SAW Sensor's signals and transform digital signal through comparator. Next the transformed signal is measured by Timer Platform and the measured interval is displayed with time. This paper proposes method of measurment of time with nano sec unit.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.17 no.3
• /
• pp.183-188
• /
• 2017

This paper is for the a study on home healthcare system for a patient using SAW Tag. This system is useful when there's a patient in home. Many patients are wounded in restroom. But restroom is very private place and nobody want to be disturbed here. The place where the patient is most injured in the house is the toilet, and it is the point where the privacy of the individual should be kept and the patient's condition should be checked and cope with in case of emergency. And using saw tag, we can calculate position and ID through reflected rf signal. Therefore we propose a general home healthcare system. The management system utilized a seat bed system to monitor at-home patients. The system mounts a bio-signal measuring unit on a toilet seat, measures a bio-signal from the bio-signal measuring unit, and the measured bio-signal is transmitted to the main server through the user's smart phone. With proposed system, we can expand operation area to silver town where many patients are cared. In this paper we developed sensor system and saw tag positioning system and showed the result.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2009.10a
• /
• pp.376-380
• /
• 2009

Surface acoustic wave (SAW) device is widely used as a bandpass filter, a chemical or physical sensor, and an actuator. In this paper, we propose the capacitive gap measurement system with high precision through the signal processing using SAW device. The research process is mainly composed of theoretical part and experimental part. In theoretical part, equivalent circuit model was used to simulate the SAW response by the change of capacitance. In experimental part, commercialized capacitor was used to see the SAW response by the change of load capacitance. After that, gap adjustment system was made physically and the SAW response by the change of gap which caused the capacitance change was measured. And resolution and stroke was decided comparing the signal change and basic measurement noise level.

• Transactions of the Society of Information Storage Systems
• /
• v.2 no.4
• /
• pp.251-256
• /
• 2006

There is a great demand of micro-actuators for mobile information devices such as SFF optical drives and mobile phone cameras. However, the magnetic coils used in conventional electromagnetic motors are a major obstacle for the miniaturization because of their complicated structures and large power consumption. In this paper, a linear ultrasonic motor to actuate focusing lens of mobile devices is proposed. The new actuator uses a ring type bimorph piezoelectric material, and $d_{31}$ mode is adopted for applying linear motion. The interaction between inertia force and friction force makes linear motion by high-frequency saw signal input. The saw signal gives steady forces on the one direction by asymmetric inclination property of the signal itself on time domain. A commercial FEM(ANSYS) was used in this investigation for simulating structural analysis, identification of dynamic property, such as resultant displacement and coupled analysis with piezoelectric material. To evaluate the performance of the new design, a prototype was manufactured and experiments were carried out. Experimental results show the actuator motion of 5.4 mm/s at 10V saw signal of 41 kHz.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.13 no.5
• /
• pp.400-410
• /
• 1988

In this paper, a fast synchronization system using SAW TDL matched filter and SAW recirculation loop not only for acquisition but also tracking in the direct sequence spread spectrum communication receiver in case of low SNR was designed and its characteristics were investigated. When signal of 16dB SNR was inputed at the receiver, the PN code of the receiver could be synchronized from the extracted signal for synchronization through SAW TDL matched filter and SAM recirculation loop for 30 recirculations. And the average synchronization time of this system was calculated. From the results, we found that this synchronization system could achieve faster synchronization of PN codes in the receiver under the circumstances of low SNR than that of using only matched filter.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.38C no.9
• /
• pp.813-821
• /
• 2013

In this paper, a vital signal sensor based on impedance variation of resonator is presented. Proposed vital signal sensor can detect the vital signal, such as respiration and heart-beat signal. System is composed of resonator, oscillator, surface acoustic wave (SAW) filter, and power detector. The cyclical movement of a dielectric such as a human body, causes the impedance variation of resonator within the near-field range. So oscillator's oscillation frequency variation is effected on resonator's resonant frequency. SAW filter's skirt characteristic of frequency response can be transformed a small amount of frequency deviation to a large variation. Aim to enhance the existing sensor detection range, proposed sensor operates in 870 MHz ISM band, and detect respiration and heart-beat signal at distance of 120 mm.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.33 no.1
• /
• pp.54-62
• /
• 2013

In this study, a wireless and non-power SAW (surface acoustic wave) temperature sensor was developed. The single inter-digital transducer (IDT) of SAW temperature sensor of which resonance frequency is 434 MHz was fabricated on $128^{\circ}$ rot-X $LiNbO_3$ piezoelectric substrate by semiconductor processing technology. To find optimal acoustic reflector for SAW temperature sensor, various kinds of acoustic reflectors were fabricated and their reflection characteristics were analyzed. The IDT type acoustic reflector showed better reflection characteristic than other reflectors. The wireless temperature sensing system consisting of SAW temperature sensor with dipole antenna and a microprocessor based control circuit with dipole antenna for transmitting signal to activate the SAW temperature sensor and receiving the signal from SAW temperature sensor was developed. The result with wireless SAW temperature sensing system showed that the frequency of SAW temperature sensor was linearly decreased with the increase of temperature in the range of 40 to $80^{\circ}C$ and the developed wireless SAW temperature sensing system showed the excellent performance with the coefficient of determination of 0.99.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.11 no.8
• /
• pp.1589-1595
• /
• 2007

Recently many communication systems ate adapting the OFDM(Orthogonal Frequency Division Multiplexing) for multimedia data services. However, OFDM has some problems that PAPR is increased when sub-carries are summed up with same phases. This problem causes severe signal distortions while the signal is passing through non-linear system such as power amplifier resulting in performance degradation of transmission system. In this paper, we use IF-Clipping method to solve PAPR problem and the signal distortion caused by clipping is limited by use of SAW (Surface Acoustic Wave) filter and power amplifier(TWTA). And we derive the optimal parameter(PAPR, Backoff) values to meet the spectrum mask of WiBro system.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.12 no.4
• /
• pp.766-771
• /
• 2008

As the practical range of SAW Device extended into various fields including physical sensor, chemical sensor and ID Tag, the platform for various SAW Devices is required more than ever. While SAW ID or Sensors advanced remarkably, the development of platform which applies to SAW Sensor left much to be desired. Therefore this paper represents the SAW platform in order to use SAW ID such as ID Tag or Sensors more conveniently. The SAW platform consists of a RF module which can recognize SAW ID and a main module which has a hish performance processor in order to process the response signal of SAW ID. The main module which has a high performance processor is designed by GUI environmental type to ensure that users are able to use the platform more easily. In this paper, the SAW platform, which is based on ARM9 core processor, used Windows Embedded CE 6.0 OS which brings friendly interface to users. Also the developers can make less effort to design various applications with sensors.