• Advances in environmental research
• /
• v.2 no.1
• /
• pp.19-33
• /
• 2013

Microalgae are receiving an increasing attention because of their potential use as $CO_2$ capture method and/or as feedstock for biofuels production. On the other hand the current microalgae-based technology is still not widespread since it is characterized by technical and economic constraints that hinder its full scale-up. In such contest the growth kinetics of Nannochloris eucaryotum (a relatively unknown marine strain) in batch and semi-batch photobioreactors is quantitatively investigated with the aim of obtaining the corresponding kinetic parameters suitable for process engineering and its optimization. In particular the maximum growth rate was evaluated to be 1.99 $10^{-3}\;h^{-1}$. Half saturation concentrations for nitrates ($K_N$) and phosphates uptake ($K_P$) were evaluated as 5.4 $10^{-4}\;g_N\;L^{-1}$ and 2.5 $10^{-5}\;g_P\;L^{-1}$, respectively. Yield factors for nitrogen ($Y_N$) and phosphorus ($Y_P$) resulted to be 5.9 $10^{-2}\;g_N\;g^{-1}$ biomass and 6.0 $10^{-3}\;g_P\;g^{-1}{_{biomass}}$, respectively. The possibility of using 100% (v/v) $CO_2$ gas as carbon source is also evaluated for the first time in the literature as far as N. eucaryotum is concerned. The strain showed a good adaptability to high concentrations of dissolved $CO_2$ as well as to low pH. The lipid content under 100% $CO_2$ is about 16.16 %wt $wt^{-1}$ and the fatty acid methyl esters composition of the extracted oil is in compliance with the European regulation for quality biodiesel.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2014.02a
• /
• pp.471.2-471.2
• /
• 2014

We demonstrate here that an improvement in precursor film density (green density) leads to a great enhancement in the photovoltaic performance of CuInSe2 (CISe) thin film solar cells fabricated with Cu-In nanoparticle precursor films via chemical solution deposition. A cold-isostatic pressing (CIP) technique was applied to uniformly compress the precursor film over the entire surface (measuring 3~4 cm2) and was found to increase its relative density (particle packing density) by ca. 20%, which resulted in an appreciable improvement in the microstructural features of the sintered CISe film in terms of lower porosity, reduced grain boundaries, and a more uniform surface morphology. The low-bandgap (Eg=1.0 eV) CISe PV devices with the CIP-treated film exhibited greatly enhanced open-circuit voltage (VOC, from 0.265 V to 0.413 V) and fill factor (FF, from 0.34 to 0.55), as compared to the control devices. As a consequence, an almost 3-fold increase in the average power conversion efficiency, 3.0 to 8.2% (with the highest value of 9.02%), was realized without an anti-reflection coating. A diode analysis revealed that the enhanced VOC and FF were essentially attributed to the reduced reverse saturation current density (j0) and diode ideality factor (n). This is associated with the suppressed recombination, likely due to the reduction in recombination sites such as grain/air surfaces (pores), inter-granular interfaces, and defective CISe/CdS junctions in the CIP-treated device. From the temperature dependences of VOC, it was confirmed that the CIP-treated devices suffer less from interface recombination.

• Geotechnical Engineering
• /
• v.12 no.1
• /
• pp.63-72
• /
• 1996

The current practice in construction of reinforced earth retaining walls is to use a granular soil for the backfill material. When the material is available in site, the construetion cost can be remarkably reduced. As the weathered granite soils are abundant and widely distributed throughout the Korean peninsula: whether they are suitable or not as the backfill material is considered to be the most important key in economic construction of the wall. This paper investigates the grain size distribution of the weathered soils which locate at many places throughout the nation and then examines limitation of their use based on the specifications of different countries. The variaton of shear strength with both different fine contents and saturation is also investigated. It is known that the grain size distribution of most weathered soils are not satisfied with the general requirement. However their use is possible in wide range when the backfill keeps in unsaturated condition using good drainage facilities and 1 or pervious reinforcements.

• Korean Journal of Materials Research
• /
• v.11 no.5
• /
• pp.378-384
• /
• 2001

In this study, nanostructured Fe-Ce powder with grain size of 10nm was produced by MA (mechanical alloying) process and was consolidated by PECS (pulse electric current sintering) process for the fabrication of bulk nanostructured Fe-Co softmagnetic alloy. PECS process was performed at 700, 800, 900 and $^1000{\circ}C$ with holding time ranging from 0 to 15min. The effectiveness of PECS Process to Produce nanostructured bulk specimens was estimated. The optimal PECS process condition for nanostructured Fe-Co powders was found through observing the change of relative density and microstructure with sintering temperature and holding time. The magnetic properties of the sintered specimens were evaluated through the measurement of coercivity and saturation magnetization.

• The Korean Journal of Emergency Medical Services
• /
• v.23 no.3
• /
• pp.7-16
• /
• 2019

Purpose: The present study was conducted to identify the factors influencing the perfromance of the emergency medical technicians (EMTs) utilizing smart advance life support (SALS) and to provide appropriate feedback to improve SALS performance. Methods: The study subjects were recruited from 119 EMT members working in G city participating in SALS project. A total of 155 data were used in the analysis. Results: Of the three areas, the mean score of importance was the highest (4.53±0.48). followed by educational needs (4.24±0.66), and SALS performance (4.08±0.55). Importance was identified as a significant factor influencing SALS performance (β=.187, p<.047).The length of education. work scope. amd role of level 1 EMTs vary significantly depending on the type of qualifications they have as emergency medical professionals, while the supply of level 1 EMTs has already reached a point of saturation. Accordingly, the current regulation on allowing level 2 EMTs with at least three years of experience to take the level 1 EMT test presents serious inequity for students just graduating from their emergency medical services program. It is also a factor that degrades the professionalism of level 1 EMTs. Conclusion: Based on the results of this study, it was found that mediation and education programs need to be implemented to highlight the importance of the tasks performed in SALS situations in order to improve performance.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.42 no.10 s.340
• /
• pp.39-50
• /
• 2005

In this paper, we propose a performance improving MAC algerian for the IEEE 802.11 DCF. WLAN based IEEE 802.11 uses two control methods called 'Distributed Coordination Function(UF)' and 'Point Coordination Function(PCF)'. The nF controls the Urnsmission based on carrier sense multiple access with collision detection(CSMA/CA), that decides a random backoff time with the range of contention window for each terminal. Normally, each terminal the CW double after collision, and reduces the CW to the minimum after successful transmission. This paper proposes an enhanced DCF algorithm that decreases the CW smoothly after successful transmission in order to reduce the collision Probability by utilizing the current status information of WLAN. We also analyze the throughput and delay performance for the unsaturated case mathematically. Simulation results show that our algorithm enhances the saturation throughput of WLAN. They also coincide well with the analytical results.

• Proceedings of the IEEK Conference
• /
• 2006.06a
• /
• pp.227-228
• /
• 2006

In this paper, we introduce the design and fabrication of 60 GHz low noise amplifier MMIC for IEEE802.15.3c WPAN system. The 60 GHz LNA was designed using ETRI's $0.12{\mu}m$ PHEMT process. The PHEMT shows a peak transconductance ($G_{m,peak}$) of 500 mS/mm, a threshold voltage of -1.2 V, and a drain saturation current of 49 mA for 2 fingers and $100{\mu}m$ total gate width (2f100) at $V_{ds}$=2 V. The RF characteristics of the PHEMT show a cutoff frequency, $f_T$, of 97 GHz, and a maximum oscillation frequency, $f_{max}$, of 166 GHz. The performances of the fabricated 60 GHz LNA MMIC are operating frequency of $60.5{\sim}62.0\;GHz$, small signal gain ($S_{21}$) of $17.4{\sim}18.1\;dB$, gain flatness of 0.7 dB, an input reflection coefficient ($S_{11}$) of $-14{\sim}-3\;dB$, output reflection coefficient ($S_{22}$) of $-11{\sim}-5\;dB$ and noise figure (NF) of 4.5 dB at 60.75 GHz. The chip size of the amplifier MMIC was $3.8{\times}1.4\;mm^2$.

• Proceedings of the IEEK Conference
• /
• 2006.06a
• /
• pp.623-624
• /
• 2006

In this paper, we introduce the design and fabrication of V-band power amplifier MMIC with excellent gain-flatness for IEEE 802.15.3c WPAN system. The V-band power amplifier was designed using ETRI' $0.12{\mu}m$ PHEMT process. The PHEMT shows a peak transconductance ($G_{m,peak}$) of 500 mS/mm, a threshold voltage of -1.2 V, and a drain saturation current of 49 mA for 2 fingers and $100{\mu}m$ total gate width (2f100) at $V_{ds}$=2 V. The RF characteristics of the PHEMT show a cutoff frequency, $f_T$, of 97 GHz, and a maximum oscillation frequency, $f_{max}$, of 166 GHz. The gains of the each stages of the amplifier were modified to have broadband characteristics of input/output matching for first and fourth stages and get more gains of edge regions of operating frequency range for second and third stages in order to make the gain-flatness of the amplifier excellently for wide band. The performances of the fabricated 60 GHz power amplifier MMIC are operating frequency of $56.25{\sim}62.25\;GHz$, bandwidth of 6 GHz, small signal gain ($S_{21}$) of $16.5{\sim}17.2\;dB$, gain flatness of 0.7 dB, an input reflection coefficient ($S_{11}$) of $-16{\sim}-9\;dB$, output reflection coefficient ($S_{22}$) of $-16{\sim}-4\;dB$ and output power ($P_{out}$) of 13 dBm. The chip size of the amplifier MMIC was $3.7{\times}1.4mm^2$.

• Journal of the Korean Magnetics Society
• /
• v.15 no.1
• /
• pp.30-36
• /
• 2005

Recently, It has been reported that the spin sprayed ferite film shows better magnetic properties at high frequeny that the ferrite by co-firing over $800^{\circ}C$ . Besides, there is no limitation to select the substrate materials because it can be processed with relatively low temperature below $100^{\circ}C$. Therefore, we fabricated film inductor as a passive device for DC-DC converter by a use of spin sprayed embedded form was completed by via hole process of pad opening. Saturation magnetization of 0.61 T and real part of permeability of 110 were obtained in Ni-Zn ferrite. In addition, inductance of 1.52 ${\mu}H$, quality factor of 24.3 at 5 MHz were measured with spiral 16 turn inductor. The rated current of inductor was 863 mA.

• Journal of Power Electronics
• /
• v.13 no.3
• /
• pp.369-380
• /
• 2013

Direct torque control based on space vector modulation (SVM-DTC) protects the DTC transient merits. Furthermore, it creates better quality steady-state performance in a wide speed range. The modified method of DTC using SVM improves the electrical magnitudes of asynchronous machines, such as minimizing the stator current distortions, the stator flux with electromagnetic torque without ripple, the fast response of the rotor speed, and the constant switching frequency. In this paper, the proposed method is based on two new control strategies for direct torque control with space vector modulation. First, fuzzy logic control is used instead of the PI torque and a PI flux controller to minimizing the torque error and to achieve a constant switching frequency. The voltages in the direct and quadratic reference frame ($V_d$, $V_q$) are achieved by fuzzy logic control. In this scheme, the switching capability of the inverter is fully utilized, which improves the system performance. Second, the close loop of stator flux estimation based on the voltage model and a low pass filter is used to counteract the drawbacks in the open loop of the stator flux such as the problems saturation and dc drift. The response of this new control strategy is compared with DTC-SVM. The experimental and simulation results demonstrate that the proposed control topology outperforms the conventional DTC-SVM in terms of system robustness and eliminating the bad outcome of dc-offset.