• Journal of the Korean Geotechnical Society
• /
• v.16 no.1
• /
• pp.145-155
• /
• 2000

Orientation data of discontinuities are of paramount importance for rock slope stability studies because they control the possibility of unstable conditions or excessive deformation. Most orientation data are collected by using linear sampling techniques, such as borehole fracture mapping and the detailed scanline method (outcrop mapping). However, these data, acquired by the above linear sampling techniques, are subjected to bias, owing to the orientation of the sampling line. Even though a weighting factor is applied to orientation data in order to reduce this bias, the bias will not be significantly reduced when certain sampling orientations are involved. That is, if the linear sampling orientation nearly parallels the discontinuity orientation, most discontinuities orientation data which are parallel to sampling line will be excluded from the survey result. This phenomenon can cause serious misinterpretation of discontinuity orientation data because critical information is omitted. In the case study, orientation data collected by using the borehole fracture mapping method (vertical scanline) were compared to those based on orientation data from the detailed scanline method (horizontal scanline). Differences in results for the two procedures revealed a concern that a representative orientation of discontinuities was not accomplished. Equal-area, polar stereo nets were used to determine the distribution of dip angles and to compare the data distribution fur the borehole method versus those for the scanline method.

• Journal of Soil and Groundwater Environment
• /
• v.8 no.2
• /
• pp.1-8
• /
• 2003

Two types of ground-water sampling techniques for CFCs (chlorofluorocarbons) analysis, the cold-welded copper tube method and flame-sealed borosilicate glass ampule method, were compared and evaluated. CFCs concentrations by the copper tube method showed a poor reproducibility among triplicates whereas those by the glass ampule method showed a good agreement and relative standard deviations of triplicates were less than 5%. The poor reproducibility of the copper tube method appears to be attributed to the incomplete sealing in connection between faucets of wellhead and the sampling apparatus. The copper tube method also showed higher CFCs concentrations than the glass ampule method, which is more pronounced for CFC-11 than for CFC-12. The plastic tubings and rubber gasket of faucets in case of the copper tube method possibly contaminated the samples with CFC-11 and CFC-12. The potential of CFCs contamination for the glass ampule method was eliminated by using stainless steel and Nylon only and by connecting the sampling equipment directly to the main discharge pipe of wellhead. The validity of the glass ampule method were also verified by detecting very low level of CFCs for the ground-water sample which is old enough to have negligible CFCs.

• Journal of Broadcast Engineering
• /
• v.8 no.2
• /
• pp.146-152
• /
• 2003

ATSC DTV receivers use repetitive data segment syncs or Gardner algorithm as a tuning recovery circuit. Many multipath signals can induce timing-offset in the symbol timing recovery circuit using Gardner algorithm and this timing-offset shifts sampling instant to the wrong points, causing the performance of the equalizer to become nr. When many echoes exist, the optimal sampling instant will be the Point at which the main-path has a peak value. In this paper, by using channel correlation techniques, we find the optimal sampling instant, thereby compensating the timing offset and improving DTV reception performance. We analyzed the Performance enhancement of DTV receivers using the timing offset compensator.

• Structural Engineering and Mechanics
• /
• v.83 no.2
• /
• pp.179-193
• /
• 2022

The shear behaviour of reinforced concrete members has been studied over the past decades by various researchers, and it can be simulated by analysing shear panel elements which has been regarded as a basic element of reinforced concrete members subjected to in-plane biaxial stresses. Despite various experimental studies on shear panel element which have been conducted so far, there are still a lot of uncertainties related to what influencing factors govern the shear behaviour and affect failure mechanism in reinforced concrete members. To identify the uncertainties, a finite element analysis can be used, which enables to investigate the impact of specific variables such as the reinforcement ratio, the shear retention factor, and the material characteristics including aggregate interlock, tension stiffening, compressive softening, and shear behaviour at the crack surface. In this study, a non-linear probabilistic analysis was conducted on reinforced concrete panels using a finite element method optimized for reinforced concrete members and advanced sampling techniques so that probabilistic analysis can be performed effectively. Consequently, this study figures out what analysis methodology and input parameters have the most influence on shear behaviour of reinforced concrete panels.

• Journal of Biomedical Engineering Research
• /
• v.17 no.2
• /
• pp.209-214
• /
• 1996

The display of biological signals in raster scan monitors often involves a multirate sampling operation which consists of decimation .and interpolation. All electroencephalouaphic (EEG) samples of 10 to 30 seconds (2, 500 to 7, 500 samples at 250[Hz] sampling frequency) must be displayed in the computer screen to keep the aspect ratio of the paper polygraph output. Since the current afrorclable display technology Plots at most 2, 000 Pixels Per row, sDme signal samples need to be discarde4 This Paper studies methods to perform this operation characterizing them from the signal processing viewpoint and compares the display quality among several decimation techniques. Experimental results show that a nonlinear operation such as the peak detection method could be preferable to the canonical linear filtering to reduce aliasing.

• Journal of Korean Society of Water and Wastewater
• /
• v.27 no.2
• /
• pp.233-239
• /
• 2013

Sampling rate of Hydraulic pressure data, depending on the intended use of the water distribution system is an important factor. If sampling interval of hydraulic data is short, that will be more useful but it demand a lot of expense for maintenance. In this study, based on simulation of water distribution system 2 khz data, statistical techniques of student t distribution, non-exceedance probability using the optimal sampling rate for research.

• Journal of Korean Society of Forest Science
• /
• v.65 no.1
• /
• pp.68-73
• /
• 1984

The purpose of this paper was to figure out the efficiencies of two sampling techniques, a simple random sampling and a two-stage P.P.S. (probability proportional to size) sampling, in estimating the volume of the mature coniferous stands near Salzburg, Austria. With black-and-white infrared photographs at a scale 1:10,000, the following four classes were considered; non-forest, young stands less than 40 years, mature beech and mature coniferous stands. After the classification, a field survey was carried out using a relascope with a BAF (basal area factor) 4. For the simple random sampling, 99 points were sampled, while for the P.P.S. sampling, 75 points were sampled in the mature coniferous stands. The following results were obtained. 1) The mean standing coniferous volume estimate was $422.0m^3/ha$ for the simple random sampling and $433.5m^3/ha$ for the P.P.S. sampling method. However, the difference was not statistically significant. 2) The required number of sampling points for a 5% sampling error were 170 for the two stage P.P.S. sampling, but 237 for the simple random sampling. 3) The two stage P.P.S. method reduced field survey time by 17% as compared to the simple random sampling.

• 한국지구물리탐사학회:학술대회논문집
• /
• 2003.11a
• /
• pp.340-343
• /
• 2003

This study presents a practical procedure for the Bayesian inversion of geophysical data by Markov chain Monte Carlo (MCMC) sampling and geostatistics. We have applied geostatistical techniques for the acquisition of prior model information, and then the MCMC method was adopted to infer the characteristics of the marginal distributions of model parameters. For the Bayesian inversion of dipole-dipole array resistivity data, we have used the indicator kriging and simulation techniques to generate cumulative density functions from Schlumberger array resistivity data and well logging data, and obtained prior information by cokriging and simulations from covariogram models. The indicator approach makes it possible to incorporate non-parametric information into the probabilistic density function. We have also adopted the MCMC approach, based on Gibbs sampling, to examine the characteristics of a posteriori probability density function and the marginal distribution of each parameter. This approach provides an effective way to treat Bayesian inversion of geophysical data and reduce the non-uniqueness by incorporating various prior information.

• Structural Engineering and Mechanics
• /
• v.3 no.3
• /
• pp.201-213
• /
• 1995

At present Level 2 and importance sampling methods are the main tools used to estimate reliability of structural systems. But sometimes application of these techniques to realistic problems involves certain difficulties. In order to overcome the difficulties it is suggested to use Monte Carlo simulation in combination with two other techniques-extreme value and tail entropy approximations; an appropriate Pearson's curve is fit to represent simulation results. On the basis of this approach an algorithm and computer program for structural reliability estimation are developed. A number of specially chosen numerical examples are considered with the aim of checking the accuracy of the approach and comparing it with the Level 2 and importance sampling methods. The field of application of the approach is revealed.

• Journal of Satellite, Information and Communications
• /
• v.9 no.3
• /
• pp.59-63
• /
• 2014

This paper describes the basic principles of 3D broadcast system and proposes new 3D broadcast technology that reduces the amount of data by applying CS(Compressed Sensing). Differences between Sampling theory and the CS technology concept were described. Recently proposed CS algorithm AMP(Approximate Message Passing) and CoSaMP(Compressive Sampling Matched Pursuit) were described. This paper compared an accuracy between two algorithms and a calculation time that image data compressed and restored by these algorithms. As result determines a low complexity algorithm for 3D broadcast system.