• Journal of agricultural medicine and community health
• /
• v.29 no.2
• /
• pp.249-263
• /
• 2004

Objectives: The objectives of the present study were to establish the exposure monitoring method of chlorpyrifos and chlorothalonil application to pear and field red pepper by vehicle-mounted sprayer, hand-held sprayer and to assess the risk. Methods and Results: Chlorpyrifos met all of requirements of sampling and analysis method(U.S. EPA), but chlorothalonil met only dermal patch method. Potential dermal and inhalation exposure was evaluated in 42 farmers. Compared with the hand-held sprayer application, vehicle mounted sprayer demonstrated producing relatively lower dermal exposure levels with statistical significance. In dermal exposure during hand-held application, there is no significant difference between pear and red pepper. Conclusions: This results show that application method is the main factor of dermal exposure. There was no statistically significant difference between each group of respiratory exposure level. The margin of safety (MOS) was calculated to assess the risk of pesticide exposure. All Chlorpyrifos MOS values are lower than 0.2, which mean working conditions are unsafe. In order to protect farmers, big efforts to control exposure are needed.

• Journal of the Earthquake Engineering Society of Korea
• /
• v.15 no.3
• /
• pp.37-43
• /
• 2011

Reliability of piping systems is essential to the safety of any important industrial facilities. During an earthquake, damage to the piping system can occur. It can also cause considerable economic losses and the loss of life following earthquakes. Traditionally, the study of the secondary system was less important than primary structure system, however it has recently been emerging as a key issue for the effective maintenance of the structural system and to help reduce nonstructural earthquake damage. The primary objectives of this study are to evaluate seismic design requirements and the seismic performance of gas and fire protection piping systems installed in reinforced concrete (RC) buildings. In order to characterize the seismic behavior of the existing piping system in an official building, 10 simulated earthquakes and 9 recorded real earthquakes were applied to ground level and the building system by the newmark average acceleration time history method. The results developed by this research can be used for the improvement of new seismic code/regulatory guidelines of secondary systems as well as the improvement of seismic retrofitting or the strengthening of the current piping system.

• Journal of the Korean Institute of Gas
• /
• v.2 no.2
• /
• pp.18-25
• /
• 1998

According to the requirements of ANSI B3l.8, the pipe thickness is determined with hoop stress resulted from internal pressure. And the other loads induced by soil, vehicle, thermal expansion, ground subsidence, etc shall be evaluated rationally. There are two ways of calculating stress of buried gas pipeline. The first is FEM. FEM can calculate the stress regardless of the complexity of pipeline shape and boundary conditions. But it needs high cost and long time. The second is the way to use equation. The reliable equations to calculate the stress of buried gas pipeline was developed and have been used in designing pipeline and evaluating pipeline safety, But these equation are very difficult to understand and use for non-specialist. For easy calculation of non-specialist, the new computer program to calculate stress of buried natural gas pipeline have been developed. The stress is calculated by the equations and extrapolation of the graph resulted from FEM. The full paper is consist of series I and II. In this paper, series I, the calculating equation of the program is explained in detail.

• Journal of the Korean Institute of Gas
• /
• v.2 no.2
• /
• pp.26-33
• /
• 1998

The thickness of buried gas pipeline is determined mainly with internal pressure and location factor according to the requirements of ANSI B3l.8. But the stress of buried gas pipeline is determined by not only internal stress but also external loads. The change of burying and environmental conditions, therefore, may result in increasing stress of pipeline. In order to avoid the decrease of safety degree resulting from change of environmental condition, the evaluation of stress level shall be necessary. The reliable equations have been developed for calculating stress of buried pipeline from internal pressure, earth load, vehicle load, ground subsidence. But they are very difficult to understand and use for non-specialist. For easy calculation of non-specialist, the new computer program to calculate stress of buried natural gas pipeline have been developed. The program can calculate maximum stress resulted from earth load, vehicle load, thermal load, four type ground subsidence. The stress is calculated by the equations and extrapolation of the graph resulted from FEM. In this paper, as the series of paper I, the operating method and the functions of the program is explained.

• Proceedings of the KOSOMBE Conference
• /
• v.1996 no.05
• /
• pp.315-319
• /
• 1996

We have developed a prototype patient monitoring system including module-based bedside units, interbed network, and central stations. A bedside unit consists of a color monitor and a main CPU unit with peripherals including a module controller. It can also include up to 3 module cases and 21 different modules. In addition to the 3-channel recorder module, six different physiological parameters of ECG, respiration, invasive blood pressure, noninvasive blood pressure, body temperature, and arterial pulse oximetry with plethysmogaph are provided as parameter modules. Modules and a module controller communicate with up to 1Mbps data rate through an intrabed network based on RS-485 and HDLC protocol. Bedside units can display up to 12 channels of waveforms with any related numeric informations simultaneously. At the same time, it communicates with other bedside units and central stations through interbed network based on 10Mbps Ethernet and TCP/IP protocol. Software far bedside units and central stations fully utilizes gaphical user interface techniques and all functions are controlled by a rotate/push button on bedside unit and a mouse on central station. The entire system satisfies the requirements of AAMI and ANSI standards in terms of electrical safety and performances. In order to accommodate more advanced data management capabilities such as 24-hour full disclosure, we are developing a relational database server dedicated to the patient monitoring system. We are also developing a clinical workstation with which physicians can review and examine the data from patients through various kinds of computer networks far diagnosis and report generation. Portable bedside units with LCD display and wired or wireless data communication capability will be developed in the near future. New parameter modules including cardiac output, capnograph, and other gas analysis functions will be added.

• Journal of Biomedical Engineering Research
• /
• v.29 no.1
• /
• pp.32-39
• /
• 2008

This paper reports on a realtime OS based master-slave configuration robot control system for laparoscopic surgery robot which enables telesurgery and overcomes shortcomings with conventional laparoscopic surgery. Surgery robot system requires control system that can process large volume information such as medical image data and video signal from endoscope in real-time manner, as well as precisely control the robot with high reliability. To meet the complex requirements, the use of high-level real-time OS (Operating System) in surgery robot controller is a must, which is as common as in many of modem robot controllers that adopt real-time OS as a base system software on which specific functional modules are implemened for more reliable and stable system. The control system consists of joint controllers, host controllers, and user interface units. The robot features a compact slave robot with 5 DOF (Degree-Of-Freedom) expanding the workspace of each tool and increasing the number of tools operating simultaneously. Each master, slave and Gill (Graphical User Interface) host runs a dedicated RTOS (Real-time OS), RTLinux-Pro (FSMLabs Inc., U.S.A.) on which functional modules such as motion control, communication, video signal integration and etc, are implemented, and all the hosts are in a gigabit Ethernet network for inter-host communication. Each master and slave controller set has a dedicated CAN (Controller Area Network) channel for control and monitoring signal communication with the joint controllers. Total 4 pairs of the master/slave manipulators as current are controlled by one host controller. The system showed satisfactory performance in both position control precision and master-slave motion synchronization in both bench test and animal experiment, and is now under further development for better safety and control fidelity for clinically applicable prototype.

• Journal of Nuclear Fuel Cycle and Waste Technology(JNFCWT)
• /
• v.14 no.3
• /
• pp.235-243
• /
• 2016

In the near future, many countries, including the Republic of Korea, will face a significant increase in low level radioactive waste (LLW) from nuclear power plant decommissioning. The purpose of this paper is to look at blending as a method for enhancing disposal options for low-level radioactive waste from the decommissioning of nuclear reactors. The 2007 U.S. Nuclear Regulatory Commission strategic assessment of the status of the U.S. LLW program identified the need to move to a risk-informed and performance-based regulatory approach for managing LLW. The strategic assessment identified blending waste of varying radionuclide concentrations as a potential means of enhancing options for LLW disposal. The NRC's position is that concentration averaging or blending can be performed in a way that does not diminish the overall safety of LLW disposal. The revised regulatory requirements for blending LLW are presented in the revised NRC Branch Technical Position for Concentration Averaging and Encapsulation (CA BTP 2015). The changes to the CA BTP that are the most significant for NPP operation, maintenance and decommissioning are reviewed in this paper and a potential application is identified for decommissioning waste in Korea. By far the largest volume of LLW from NPPs will come from decommissioning rather than operation. The large volumes in decommissioning present an opportunity for significant gains in disposal efficiency from blending and concentration averaging. The application of concentration averaging waste from a reactor bio-shield is also presented.

• Journal of KIISE:Information Networking
• /
• v.37 no.6
• /
• pp.420-430
• /
• 2010

Due to increasing demand for improving road safety and optimizing road traffic, Vehicular Ad-Hoc Networks (VANET) have been subject to extensive attentions from all aspects of commercial industry and academic community. Security and user privacy are fundamental issues for all possible promising applications in VANET. Most of the existing security proposals for secure VANET concentrate authentication with privacy preservation in vehicle-to-vehicle (V2V) and vehicle-to-roadside infrastructure (V2I) communications and require huge storage and network capacity for management of revocation list. Motivated by the fact, we propose a new scheme with security and privacy preservation which combines V2V and V2I communication. With our proposed scheme, the communication and computational delay for authentication and overhead for management of revocation list can be significantly reduced due to mutual authentication between a vehicle and a Roadside Unit (RSU) requires only two messages, and the RSU issues the anonymous certificate for the vehicle on behalf of the Trust Authority (TA). We demonstrate that the proposed protocol cannot only guarantee the requirements of security and privacy but can also provide efficiency of authentication and management of revocation list.

• Journal of the Korean Institute of Gas
• /
• v.14 no.6
• /
• pp.15-20
• /
• 2010

Compressed Natural Gas (CNG) buses have been supplied since the year 2000 in order to resolve severe atmospheric pollution in metropolitan area and contributed on the improvement of urban atmospheric environment. However, it is indispensible to take an adequate measure to guarantee the safety of CNG vehicles because of the possibility of huge fire accident. A receptacle, connecting device between high pressure fuel supply tank and fuel line, plays an important role in CNG supply system. In recent, leakage of CNG from receptacles has been reported. So, the concern about the security and reliability of receptacles has been arisen. Therefore, a lot of efforts to prevent leakage are invested among researchers and the durability of this component should be guaranteed despite repeated operation. This research has performed durability tests of a CNG receptacle regarding the repeated usage, extreme chattering, and continuous full flow test. Although a receptacle used for CNG vehicle satisfies validation requirements in the test results, it has been found that failure in the function of leakage prevention in a receptacle could take place in the case of prolonged exposure to high supply pressure in common quick charging environment on site.

• Journal of Fashion Business
• /
• v.12 no.5
• /
• pp.1-13
• /
• 2008

This study is largely aimed at presenting ways to improve the working clothes and help companies create more positive images by suggesting designs of the clothes, which take into accounts the corporate image, symbolism, function and aesthetic appreciation through introduction of companies' CIP. And, it is significant to propose working clothes development condition and process with introduction of companies' CIP(Corporate Identity Program : work that systematize and simplify visually images which companies or public bodies have) A way of this study was made up with working clothes design development process which a student planned. First of all, this study looked into Company D's Corporate Identity Program(CIP) to develop the design that corresponds with the characteristics of the company's favorite design, working environment and demands of the employees. And, then, the study conducted a survey of 30 employees and intensive interviews with heads of four teams including the Safety Team, the Working Clothes Management Team and the General Affairs Team to find out the requirements of the clothes and the characteristics of the company. Based on them, the concrete image that the company pursues and the direction of design were set up through image positioning. In the end, three different concept designs were presented through image-mapping and the concrete design of each item was developed. A total of seven items including upper and lower garments (a jacket and trousers) for the spring-summer seasons, upper and lower garments (a jumper and trousers) for the winter season, cold-protecting vest and winter clothes (a coat and trousers) were presented in accordance with the three concepts. One of the concept designs, which was selected through evaluation by employees of Company D, was produced as a sample and then the final design was chosen after a discussion attended by the head of each team and representatives of the employees. Based on the aforementioned design planning, one design was selected from each of the three concept designs for production. And each of these was requested to special production enterprise and manufactured. Following the result of study, by looking into a case of a practical joint design project between a university and a company, this study suggested ideas for business to improve working clothes through the academic-industrial cooperation and presented conditions and process of design development. And, this study also aims to examine the feasibility of academic-industrial cooperation based on the cases in which enterprises and universities staged joint projects to develop working clothes.