• Journal of the Korean Society for Nondestructive Testing
• /
• v.26 no.5
• /
• pp.315-320
• /
• 2006

This paper describes stress analysis and fatigue limit evaluation of plate with V-notch and hole-notch by lock-in infrared thermography. Temperature variation of a specimen under cyclic loading is negatively proportional to the sum of principle stress change and the surface temperature measured by infrared camera is calculated to the stress of notch specimens, based on thermoelastic equation. And also, fatigue limitation can be evaluated by the change of intrinsic energy dissipation. Fatigue limitation of two notch specimens is evaluated as 164 MPa and 185 MPa, respectively and the stress measured by Lock-in infrared Thermography show good agreement within 10% error.

• Journal of the Korean Society of Safety
• /
• v.26 no.2
• /
• pp.32-35
• /
• 2011

Experimental studies were carried out in an explosion chamber to investigate the influences of multiple cylinder obstacles on local flame propagation. The chamber dimension is 235 mm in height with a $1,000{\times}950\;mm^2$ rectangular cross section and a large vent area of $1,000{\times}320\;mm^2$. Multiple cylinder bars with obstruction ratio of 30% were used. In order to examine the interaction between the propagating flames and the obstacles, temporally resolved flame front images were recorded by a high speed video camera. The propagation behaviour of local flame fronts around the left obstacle was analyzed in terms of two different methods such as the incremental burnt area divided by the flame front length and the average of the local propagation velocity determined at each point along the flame front. It was found that two methods give good consistency.

• Nuclear Engineering and Technology
• /
• v.48 no.6
• /
• pp.1330-1337
• /
• 2016

A visualization test of the fuel-coolant interaction in the Test for Real cOrium Interaction with water (TROI) test facility was carried out. To experimentally simulate the In-Vessel corium Retention (IVR)- External Reactor Vessel Cooling (ERVC) conditions, prototypic corium was released directly into the coolant water without a free fall in a gas phase before making contact with the coolant. Corium (34.39 kg) consisting of uranium oxide and zirconium oxide with a weight ratio of 8:2 was superheated, and 22.54 kg of the 34.39 kg corium was passed through water contained in a transparent interaction vessel. An image of the corium jet behavior in the coolant was taken by a high-speed camera every millisecond. Thermocouple junctions installed in the vertical direction of the coolant were cut sequentially by the falling corium jet. It was clearly observed that the visualization image of the corium jet taken during the fuel-coolant interaction corresponded with the temperature variations in the direction of the falling melt. The corium penetrated through the coolant, and the jet leading edge velocity was 2.0 m/s. Debris smaller than 1 mm was 15% of the total weight of the debris collected after a fuel-coolant interaction test, and the mass median diameter was 2.9 mm.

• Journal of Fashion Business
• /
• v.14 no.6
• /
• pp.53-69
• /
• 2010

This study compared the work environment colors and the colors of working clothes by conducting a field survey of domestic machinery manufacturers who are playing a central role in Korean industries so as to develop and evaluate working clothes based on the safety of workers and environmental harmony. For the study method, after the color-related requirements were collected through interviews and field surveys, the fabrics for working clothes were woven and the colors were selected using the requirements. The designs of working clothes were developed with an emphasis on color design. The colors of the working clothes were also analyzed in their relationship to the working environment. The evaluations were separately performed for the appearance and the colors with workers of D machinery manufacturing company. The appearance and color satisfaction, safety, psychology, and harmony with environment were evaluated on a 5-point scale by workers and their safety managers. Furthermore, pictures of the workers in their existing working clothes and the newly developed working clothes were taken with a digital camera while they were working in the field. The RGB values of the pictures were extracted using Photoshop ver. 7.01, which were converted to HVC values using Munsell Conversion ver. 4.0.1. This study found that higher satisfaction levels were shown for the newly developed working clothes compared to the existing ones. The actual measurements also showed that the newly developed had higher brightness and clearer chromatic contrast than the existing ones, indicating higher explicitness and attention for safety of workers. These types of studies can contribute to the integrated working environment plan of machinery manufacturers.

• Journal of the Korean Society of Safety
• /
• v.34 no.1
• /
• pp.40-44
• /
• 2019

Experimental studies have been carried out to investigate characteristics of gas explosion using a multi layered water gel barrier in a vented explosion chamber. The chamber is consisted of 1600 mm in length, with a square cross-section of $100{\times}100mm^2$. The gel concentration of inner layer of MLWGB ranged from 10% to 90% with intervals of 10% by weight of gel. Displacement of the MLWGB was photographed with a measured using a high-speed video camera, and pressure development was measured using a data acquisition system. It was found that MLWGBs with 10 ~ 20% inner layer concentrations were ruptured during the explosions. As the concentrations of inner layer increased from 30% to 90%, the barriers were not ruptured. As the gel concentrations of the inner layer increased, the displacement increased toward the chamber exit and the pressure decreased for the ruptured barriers. It was found that the pressure attenuation obtained from the MLWGB was higher than that of the single water gel barrier. For the cases of non-ruptured barriers, the pressure inside the chamber less increased with increasing gel concentrations of the inner layer. It was also found that the displacement moved back into the chamber for non-ruptured MLWGBs, and it was sensitive to the gel concentrations.

• Smart Media Journal
• /
• v.11 no.3
• /
• pp.90-101
• /
• 2022

Buses are a popular means of transportation. As such, thorough preparation is needed for passenger safety management. However, the safety system is insufficient because there are accidents such as a death accident occurred when the bus departed without recognizing the elderly approaching to get on in 2018. There is a safety system that prevents pinching accidents through sensors on the back door stairs, but such a system does not prevent accidents that occur in the process of getting on and off like the above accident. If it is possible to predict the intention of bus passengers to get on and off, it will help to develop a safety system to prevent such accidents. However, studies predicting the intention of passengers to get on and off are insufficient. Therefore, in this paper, we propose a 1×1 CNN3D-based getting on and off intention prediction model using skeleton keypoints of passengers extracted from the camera image attached to the bus through UDP-Pose. The proposed model shows approximately 1~2% higher accuracy than the RNN and LSTM models in predicting passenger's getting on and off intentions.

• International conference on construction engineering and project management
• /
• 2020.12a
• /
• pp.313-322
• /
• 2020

The recognition of the risk hazards is a vital step to effectively prevent accidents on a construction site. The advanced development in computer vision systems and the availability of the large visual database related to construction site made it possible to take quick action in the event of human error and disaster situations that may occur during management supervision. Therefore, it is necessary to analyze the risk factors that need to be managed at the construction site and review appropriate and effective technical methods for each risk factor. This research focuses on analyzing Occupational Safety and Health Agency (OSHA) related to risk zone identification rules that can be adopted by the image recognition technology and classify their risk factors depending on the effective technical method. Therefore, this research developed a pattern-oriented classification of OSHA rules that can employ a large scale of safety hazard recognition. This research uses joint reasoning of risk zone Identification and numeric input by utilizing a stereo camera integrated with an image detection algorithm such as (YOLOv3) and Pyramid Stereo Matching Network (PSMNet). The research result identifies risk zones and raises alarm if a target object enters this zone. It also determines numerical information of a target, which recognizes the length, spacing, and angle of the target. Applying image detection joint logic algorithms might leverage the speed and accuracy of hazard detection due to merging more than one factor to prevent accidents in the job site.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.24 no.1
• /
• pp.65-74
• /
• 2024

In recent years, image processing technology has played a critical role in the field of autonomous driving. Among them, image recognition technology is essential for the safety and performance of autonomous vehicles. Therefore, this paper aims to develop a hybrid image recognition system to enhance the safety and performance of autonomous vehicles. In this paper, various image recognition technologies are utilized to construct a system that recognizes and tracks objects in the vehicle's surroundings. Machine learning and deep learning algorithms are employed for this purpose, and objects are identified and classified in real-time through image processing and analysis. Furthermore, this study aims to fuse image processing technology with vehicle control systems to improve the safety and performance of autonomous vehicles. To achieve this, the identified object's information is transmitted to the vehicle control system to enable appropriate autonomous driving responses. The developed hybrid image recognition system in this paper is expected to significantly improve the safety and performance of autonomous vehicles. This is expected to accelerate the commercialization of autonomous vehicles.

• Nuclear Engineering and Technology
• /
• v.56 no.2
• /
• pp.715-727
• /
• 2024

During fast neutron imaging, besides the dark current noise and readout noise of the CCD camera, the main noise in fast neutron imaging comes from high-energy gamma rays generated by neutron nuclear reactions in and around the experimental setup. These high-energy gamma rays result in the presence of high-density gamma white spots (GWS) in the fast neutron image. Due to the microscopic quantum characteristics of the neutron beam itself and environmental scattering effects, fast neutron images typically exhibit a mixture of Gaussian noise. Existing denoising methods in neutron images are difficult to handle when dealing with a mixture of GWS and Gaussian noise. Herein we put forward a deep learning approach based on the Swin Transformer UNet (SUNet) model to remove high-density GWS-Gaussian mixture noise from fast neutron images. The improved denoising model utilizes a customized loss function for training, which combines perceptual loss and mean squared error loss to avoid grid-like artifacts caused by using a single perceptual loss. To address the high cost of acquiring real fast neutron images, this study introduces Monte Carlo method to simulate noise data with GWS characteristics by computing the interaction between gamma rays and sensors based on the principle of GWS generation. Ultimately, the experimental scenarios involving simulated neutron noise images and real fast neutron images demonstrate that the proposed method not only improves the quality and signal-to-noise ratio of fast neutron images but also preserves the details of the original images during denoising.

• Journal of the Korean Society of Clothing and Textiles
• /
• v.34 no.3
• /
• pp.540-552
• /
• 2010

This research forms preliminary data for the coordination of environmental color planning in industry through a color analysis of work clothes and the work environment. A digital camera was used to study the work environment of two major shipbuilding companies located in Geoje city and Goseong county. The picture data was analyzed as G (ground: environment) and F (figure: clothes), and analyzed hue, value, and the chroma value through a Muncell conversion 9.0.6 from the color cluster, number of pixel, and RGB value. The results are as follows: First, GY, Y color were mostly used in the shipbuilding environment and work clothes. The color value was used in a relatively wide range but very low chroma (0-3), dark grayish, grayish tone dominated both fields. Second, the use of limited colors cannot be secured for safety in attention of the shipbuilding field. Third, unclear and vogue colors lessened the optical tiredness of workers that helped in the prevention of industrial accidents. Color combination and color selection should be considered for a secure safety color coordination between work clothes and the work environment when it comes to complicated color principles.