• Proceedings of the Korean Institute of IIIuminating and Electrical Installation Engineers Conference
• /
• 2007.11a
• /
• pp.209-212
• /
• 2007

It is increased electrical energy consumption with the development of intelligence society in buildings and thus an energy conservation through efficient use of electricity and reliability, safety, etc became more important. This research paper intensively investigated performance based construction specifications and design criteria of electrical installations in domestic and foreign country. It is necessary to analyze the key features based on performance and general trend about contractor guarantee, warranty method, performance design criteria from the investigated data. This paper shows a reasonable performance based construction specifications and design criteria of electrical installations.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2009.05a
• /
• pp.551-552
• /
• 2009

These days in execution of building works are increasing possibility of defect occurrences. On this, construction safety policy has been enforcing prevention for fault construction. But argument in relation to defects is increasing every day, because regulations for defects are abstract and uncertain. Therefore we analyzed patterns and reasons of defect, researched into question for rational solution about defect responsibility and responsibility period of a warranty in argument.

• Human Ecology Research
• /
• v.54 no.1
• /
• pp.27-43
• /
• 2016

This study initiates from the question of whether current advertising regulations are appropriate to be applied to the market. It confirms the relationship between misleading online advertisements of weight-loss food and consumer damages. This study argues that it is necessary to enforce monitoring and regulating (strengthening monitoring) for situations where misleading advertisements are exposed in the market with subsequent consumer damages. However, deregulation is needed for advertisements exposed in the name of misleading advertisements but with no consumer damages. In conclusion, the regulations of current weight loss foods are properly established $vis-{\grave{a}}-vis$ the market situation. However, misleading advertisements are prevalent for all regulated types: Type I (product quality and effect), Type II (endorsement and warranty), Type III (ways to use and safety), Type IV (comparison and superiority), and Type V (company information). Promotion targeting businesses, market monitoring and control are necessary to ensure that advertising regulations (which have existed only as an institution) can be appropriately applied. It is also confirmed that 'comparison advertising' (applicable to Type IV where consumer damages were not shown compared to other regulations) does not have an actual effect as a consumer protection regulation that should be considered in regulation revisions. Consumers also did not recognize Type III and V in the purchasing stage while consumer damages were demonstrated; consequently, this implies that consumers need to check and become attentive to these types.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.22 no.3
• /
• pp.203-209
• /
• 2014

The rear center-hinge bracket is designed for supporting and folding the rear-seat backrest. This bracket needs to be strong enough to be able to rigidly hold the rear-seat backrest and to withstand luggage loads from the car trunk that are generated when a vehicle is driving on the roads. Particularly, current accident studies report that many serious occupant injuries occurred when the rear-seat back easily folded inward toward the car interior, driven by the luggage loads in the trunk. Given this fact, the robust design of the rear center-hinge bracket that mainly supports the rear backrest has become more important for providing customer safety and preventing high warranty and durability problems. However, none of the studies have emphasized its significant role and considered its robust optimization. Therefore, this paper presents how the hinge-bracket design is optimized based on an application of the finite-element method coupled with the parameter design using Taguchi's design experiment. Finally, Taguchi method's application optimizes a robust center-hinge bracket that shows more rigid performance although it has lighter weight and thinner thickness.

• International Journal of Reliability and Applications
• /
• v.11 no.1
• /
• pp.55-67
• /
• 2010

There has been a recent upsurge in demand for the improvement of car reliability in the Northern American which is the primary market of South Korea automobile industry. It has been required that the warranty for transmission control unit for passenger cars directly related to passenger safety or security should be extended for 10 years and 160,000 km. In this paper, the test method for reliability and evaluation criteria is presented to evaluate the reliability on the automatic transmission controller. Reliability certification test can be roughly divided into two types: a quality test and life assessment test and a quality test can be subdivided into a basic performance test and environmental resistance test. There are 3 types of tests on the performance test for automatic transmission controller and environmental resistance test is composed of 14 items. Life test is performed with only the product passed this quality test. In this study, operation limit test at the high-temperatures, accelerated life test under specific temperature and accelerated life test for 2 or 3 stress levels are shown as a way for life test.

• Membrane and Water Treatment
• /
• v.8 no.2
• /
• pp.137-147
• /
• 2017

A water treatment utility in South Korea operates a large system of pressurized hollow fiber membrane (PHFM) modules. The optimal selection of membrane module for the full scale plant was critical issue and carried out using Risk-based Life Cycle Cost (RbLCC) analysis based on the historical data of operation and maintenance. The RbLCC analysis was used in the process of decision-making for replacing aged modules. The initial purchasing cost and the value at risk during operation were considered together. The failure of modules occurs stochastically depending on the physical deterioration with usage over time. The life span of module was used as a factor for the failure of Poisson's probability model, which was used to obtain the probability of failure during the operation. The RbLCC was calculated by combining the initial cost and the value at risk without its warranty term. Additionally, the properties of membrane were considered to select the optimum product. Results showed that the module's life span in the system was ten years (120 month) with safety factor. The optimum product was selected from six candidates membrane for a full scale water treatment facility. This method could be used to make the optimum and rational decision for the operation of membrane water purification facility.

• Journal of the Korean Institute of Gas
• /
• v.11 no.1 s.34
• /
• pp.23-28
• /
• 2007

This paper presents an experimental investigation on the sealing defects and cracks of O-rings and a valve packing of a gas valve for a LPG cylinder. O-ring in which stops a gas leakage of a liquefied petroleum gas is very important for a LPG valve safety. Valve packing is to open and close a gas flow port for supplying and charging a LPG fuel. The sealing performance of two sealing units ism related to the leak safety and long lift of a gas valve. The investigated results show that most of O-rings was failed due to a circumferential crack in which is caused by partial press bonding failure near the partition zone and an excess compression rate. Some of the O-ring failure was originated by an extrusion of an excessive leak pressure of a LP gas. Thus, this paper strongly recommends a tight quality control and a safety guarantee system of O-rings and valve packing to guarantee a leak safety and to extend a service lift of a gas valve. At the end, a warranty policy of the sealing units should be adopted for increasing a product quality and safety of a gas valve.

• Journal of Arbitration Studies
• /
• v.10 no.1
• /
• pp.92-113
• /
• 2000

Products liability refers to the liability of any or all parties along the chain of manufacture of any product for damage caused by that product. This includes the manufacturer of component parts (at the top of the chain), an assembling manufacturer, the wholesaler, and the retail store owner (at the bottom of the chain). Products containing inherent defects that cause harm to a consumer of the product, or someone to whom the product was loaned, given, etc., are the subjects of products liability suits. The goal of products liability system should be to maximize consumer welfare by efficiently providing just compensation for injuries incurred and deterring future injuries without unreasonably impeding the supply of the goods and services to consumers. Some advanced countries, apart from relying on products liability systems, also apply other policies and legislation directly aimed at the safety of the consumer. The application of general safety policies as well as products liability rules is not costless. An efficient system will not eliminate risk from society. An efficient system ... that maximises consumer welfare ... maximises the benefits while minimising the costs. Products liability claims can be based on negligence, strict liability, or breach of warranty of fitness depending on the jurisdiction where the claim is based. In view of international business and law circumstances, it should be stressed that international enterprises in Korea should consider how to cope with the situation of international transaction. International enterprises should have a correct perception about products liability which is to contribute the stabilization and improvement of the people's life and the sound develpement of the national economy. Products liability system creates incentives that influence behaviour and performance in ways that are desirable, such as more diligent monitoring to prevent defective products from reaching the market-place. At the same time, any liability system will impose burdens that are undesirable, such as greater costs imposed on business and consumers and reduced avaiability of consumer goods. The concern for society is to balance. The ideal situation is where the cost imposed on producers of goods and services pushes them to a desirable level of care but not so far that producers reach undesirable level of caution that may deprive consumers unnecessarily of the benefits from new and innovative products.

• Journal of Energy Engineering
• /
• v.21 no.2
• /
• pp.119-123
• /
• 2012

Although LNG storage tanks are very delicate with chloride attack owing to its operating inshore location, specific integrity management system for chloride attack has not been studied so far. As the design warranty life time, about 25 years, has come, to prevent paying huge amount of construction cost and required resources for new alternative storage tanks and manage the life time of operating storage tanks, the basic data of chloride attack is necessary. This study intended to build up basic data for following detailed study to develop technologies for life time management of LNG storage tanks, NT Build 492 method in North Europe was used to test chloride diffusion coefficient for the newly-constructing concrete outer tank. Results of these tests lead us to the conclusion that 90 days diffusion coefficients show 46% of 28 days' due to a large quantity of fly ash mixing and much similar to estimation from concrete process table. It seems resonable to conclude that 90 days specimens are recommended estimating the chloride diffusion coefficient for LNG storage tanks to enhance the reliabilities.

• Journal of Korea Port Economic Association
• /
• v.26 no.3
• /
• pp.92-113
• /
• 2010

The purpose of this study aims to analyse the implied terms of safe berth under Voyage charterparty with the Rebon case. Where the safety of the berth is warranted, but not the safety of the port, then the charterer's obligation is to nominate a berth which can be approached safely from within the port and which was itself, save insofar as affected by hazards or risks which affect the port as a whole or all of the berths within it. This case is an appeal from an order made by the judge dismissing an appeal from a final declaratory award on preliminary issues made by arbitrators. The judge expressed the question for decision somewhat differently as follows: if a specific load port is named in a voyage charterparty and there are several possible berths within that port to which a vessel could be directed to load by the charterers and there is no express warranty in the charterparty of the safety of either the port or the berth to which the vessel is to be directed by the charterers, is the charterparty subject to an implied term that the charterers must nominate a safe berth at that load port?