• 한국안전학회지
• /
• 제13권1호
• /
• pp.34-39
• /
• 1998

This paper describes a evaluation method of sound power radiated from the vibrating faces of a single stage gear box using sound radiation. The vibration caused from meshing gears is transmitted to the gear box faces through shafts and bearings. A Boundary Element Method (BEM) is developed to calculate the sound power radiated from the faces with their velocity response which is based on the Building Block Approach (BBA). Radiation efficiency as well as the sound intensity on the surface of the gear box is also calculated. Sound power of the gear box is larger in the case that bearings have offset to the wall of the gear box than that bearings are on the center of the gear box. The sound power increases with the augmentation of the offset.

• 한국건축시공학회지
• /
• 제8권2호
• /
• pp.131-136
• /
• 2008

Safety management is the most important factor in the construction industry. If the construction company don't control the risk, it causes the accident which give the company fatal loss. According to the Korea industrial safety analysis reports, the 25.72% of the disasters are from the construction industry, and the 13.6% construction disasters are caused by not properly using the safety gears. Therefore, this study is to investigate the Wearing Safety Gear by Occupational Classification and the Satisfaction in the Construction Field. The results are ; Carpenters are dissatisfied with the safety shoes and belt, re-bar workers are dissatisfied with the safety helmet and shoes, Concrete workers are dissatisfied with the safety helmet and goggles.

• 열처리공학회지
• /
• 제32권6호
• /
• pp.270-274
• /
• 2019

In this study, simulation structure analysis was performed for the differential gear system for passenger cars as a prerequisite for the design of the balancing module. The differential gear system was modeled by using CATIA and simulation structure analysis was performed using ANSYS software. The material of the modeled differential gear system uses the mechanical properties of S45C (Q&T). In the structural analysis of the differential gear, the areas where the maximum stress and the maximum strain occurred can be identified. The maximum stress and maximum strain occurred in the pitch circle of the bevel gear. In evaluating the safety factor, it was found that sufficient safety factor was secured. Based on the analysis results for the differential gear, it is expected that it will be a good reference if we design the balancing module device.

• Journal of Biosystems Engineering
• /
• 제41권1호
• /
• pp.1-11
• /
• 2016

Purpose: The gear strength of a new mechanical transmission designed to increase the loading weight of small 4.8 kW tracked agricultural transporters was analyzed. Design improvements to increase the gear strength and reduce the gear weight were proposed after examining the parameters. Methods: Sixteen operators from three regions were surveyed to obtain the usage profile of small 4.8 kW transporters. Gear strength was evaluated by calculating contact stress and tooth root stress using commercial software following ISO 6336. Results: From the strength calculation for each gear pair, contact stress smaller than tooth root stresses were produced in all gear pairs. The safety factors in most cases exceeded 1.0, except in the case of gear pair II in group II. The design life of the transporter using gear pair II in group II was 42% under harsh conditions-thus, this design life needs improvement. A robust design was proposed by examining the relevant parameters (face width and profile shift coefficient) to increase the design life of the transporter. In addition, a lightweight design for gear pair I in group II that was considered overdesigned was proposed by examining the face width to reduce the weight of the drive gear by 42% and that of the driven gear by 30%. Conclusions: The Safety factor for the design life was examined through a gear strength analysis. After examining the relevant parameters, conditions for strength improvement were proposed to increase design life or adjust overdesigned gear. However, load conditions differ depending on the working conditions or user's preferences; therefore, it is necessary to conduct further studies in various regions.

• 대한안전경영과학회지
• /
• 제24권1호
• /
• pp.11-19
• /
• 2022

In order to find out the management and sanitation status of protective gear provided at the construction site, a case study and survey were conducted by visiting the site. As a result of the case study, inspection and management, disinfection, and storage of protective equipment were insufficient in both workplaces with less than 50 employees and workplaces with more than 100 employees. As a result of the survey, workers(66.2%), said they did not know how to identify hard hats(67.6.%), how to identify bad hard hats(60.8%), and how to identify bad safety belts (73.0%), even though workers(66.2%) were educated on protective gear, and those in charge of protective gear Non-specified(56.8%), regular inspection of the provided protective equipment was not performed(82.4%), and disinfection was not performed(90.5%). Therefore, as a management plan to maintain the performance of personal protective equipment, educational aspects, regular training on protective equipment, training on how to identify defective protective equipment, management of recording papers, technical aspects, strengthening of standards for placement of dedicated safety managers in small workplaces, participation of workers' representatives when selecting protective equipment, and selection of protective equipment for workers Providing opportunities, administrative aspects of protective equipment regulation and management, introduction of sanitary and cleanliness system, and selection of personnel in charge of protective equipment management were suggested.

• 한국산업융합학회 논문집
• /
• 제9권4호
• /
• pp.269-276
• /
• 2006

Strength Design method for involute spur gears is developed. The developed gear strength design system can design the optimized gear that minimize the number of pinion teeth with face tooth. Method of optimization is matrix form which is developed from this study. Design variables are transmitted power, gear volume, gear ratio, allowable contact stress and allowable bending stress, etc. Gear design method developed this study can be apply to the gears of plants, machine tools, automobiles.

• 한국기계가공학회지
• /
• 제16권3호
• /
• pp.146-152
• /
• 2017

Stabilizing the operation of dual fuel diesel engines is very important. The shipbuilding industry is rapidly growing, but gear components requiring reliability are still imported from other countries. The reasoning for this is three-fold. Firstly, it is compulsory that all ships must use devices that meet the performance standards specified in the Safety of Life at Sea (SOLAS) and the convention of MARine POLlution (MAPOL) to prevent pollution caused by ships. Secondly, most ships must comply with the ship classifications specified by ship owners. Therefore, it is specified that key engine gear components must be inspected and authorized for the quality and performance specified by the Ship Register Authority. Thirdly, it is essential that devices (engine gear) for human safety in ships comply with quality standards specified in the regulations and rules by the government. The Ship Register Authority's strict quality standards and approval requirements contribute to the reduction of motivation towards new investment and technology development by device component manufacturers. Therefore, this study aims to develop a method for using infrared thermography to examine gear reliability in order to ensure gear component reliability and national competitiveness in the global market.

• Tribology and Lubricants
• /
• 제32권4호
• /
• pp.113-118
• /
• 2016

As an economic, high quality, and highly reliable gear with low noise and low vibration is demanded, an overall finite element analysis regarding a gear is required. Also, an infrared thermography test, which is a quantitative testing technique, is demanded for safety and longer lifespan of gear products. In order to manufacture a gear product or to determine safety of a gear being used, it is necessary to precisely determine ingredients of a material constituting a gear and detect any internal defect. This study aims to realize a design that minimizes the spur gear displacement with respect to power during its rotation and ensures the spur gear control capacity by using a 3D model and the midasNFX program. This facilitates the assessment of the possibility of cracking by evaluating the stress intensity and focusing on the integrity of the spur gear. We prepare the specimen of the spur gear based on the possibility of cranking as per the result of the structural interpretation from an infrared ray thermal measuring technique. After cooling the spur gear, we perform experiments using thermography and halogen lamps and analyze the temperature data according to the results of the experiment. In the experiment which we use thermography after cooling, we find a rise in the temperature of the room. As a result, the defective part show temperatures lower than their surroundings while the normal parts have temperatures higher than the defective parts. Therefore, it possible to precisely identify defective part owing to its low temperature.

• 한국공작기계학회논문집
• /
• 제15권2호
• /
• pp.16-23
• /
• 2006

Recently the design of multi-stage gear drive is being highly concerned. Until now, since the researches of gear drive are focused on the design for satisfying safety factor, the reliability evaluation of multi-stage gear drive is not included. In this paper, the life and reliability models of multi-stage gear drive are proposed using methods of probability and statistics. The life and reliability of the multi-stage gear drive have been evaluated, which is based on the life and reliability of each stage gear drive. The pinion and gear lives of each stage are calculated using the Lundberg-Palmgren theory and the Weibull failure distribution. These lives are combined using methods of probability and statistics to produce a life and reliability model of multi-stage gear drive.

• 한국안전학회지
• /
• 제10권4호
• /
• pp.13-21
• /
• 1995

On mini-bus with diesel engine, at idle rpm for taking measurement to reduce gear rattle noise, was tested by the three clutch disc samples by turns, then measured the fluctuation of revolution of engine & transmission and parallel vibration of differential gear & transmission. By analyzing the measured data, the gear rattle noise, the matching design and tuning technic of transmission are comprehended and established. Conclusions of this test are as follows ; (1) Fluctuation of revolution on transmission is greatly affected by torsion of clutch disc according to fluctuation of engine revolution transmit to transmission through clutch system. Especially, gear rattle noise can be reduced by minimaizing the fluctuation of the revolution of transmission using pre-damper type clutch disc. (2) The reason of gear rattle noise is higher in summer than winter and driving longer period than initial driving is due to affection by drag torque changing. So, it is necessary for manufacturer to choose proper oil to transmission. (3) It can be occurred jumping and crash noise by applying the pre-damper type clutch disc for reducing the gear rattle noise. So, it is necessary to do test with actual vehicle according to test procedure.