• Proceedings of the KIEE Conference
• /
• 1997.07c
• /
• pp.903-906
• /
• 1997

When large capacity generation stations that consist of several large units tend to pull out of step from main power system, stabilizing control scheme as emergency control for preventing loss of synchronism of the whole stations with the remaining system is devided into two steps that the first step is to perform on-line prediction for out-of-step and the next step is on-line calculation of the amount of generation shedding for the rest of generators to be in step when out of step is expected. This paper presents on-line prediction scheme for out-of-step based on P-$\delta$ curve estimation using real-time measurement and on-line calculation of generation shedding. The proposed stabilizing scheme was applied to case study of real power system and the results obtained by the method compare well with the results by simulation.

• Journal of the Korean Society of Groundwater Environment
• /
• v.7 no.1
• /
• pp.20-23
• /
• 2000

A general solution for determining the storage coefficient from multi-step pumping test recovery data is suggested. This solution is essentially based on the method of Banton and Bangoy (1996), which used single-step pumping test recovery data. The suggested solution can be applied to any-step pumping test recovery data. We have demonstrated the applicability of the general solution to single-, double-, and triple-step pumping and/or step-drawdown test data partially described in Lee and Lee (1999). The estimates of storage coefficient as well as transmissivity are well consistent with the values from other methods for pumping phase data.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.27 no.11
• /
• pp.20-26
• /
• 2013

This paper proposes the maximum power point tracking(MPPT) control of photovoltaic system using fuzzy based variable step size perturbation & observation(FVSS-PO) method. Conventional PO and incremental conductance(IC)MPPT control algorithm generally uses fixed step size. A small fixed step size will cause the tracking speed to decrease and tracking accuracy of the MPP will decrease due to large fixed step size. Therefore, the fixed step size can't be satisfying both the tracking speed and the tracking accuracy. This paper proposes FVSS-PO MPPT algorithm that adjusts automatically step size of PO by fuzzy control according to operating conditions. The validity of MPPT algorithm proposed in this paper prove through compare with conventional PO MPPT algorithm.

• Journal of the Semiconductor & Display Technology
• /
• v.9 no.3
• /
• pp.5-9
• /
• 2010

Recently, the important issues of solar cell are low cost and high efficiency. Making low cost and high efficiency solar cell, there are many effects to development of inexpensive wafer, simplify process and improve optical, electrical properties. In this the study, the 2 step texturing method using micro blaster was developed to decrease reflection of incident lights. Air bridge electrode structure is suggested to expand the effective surface area and decrease the series resistance of finger electrode. The effects of 1 step texturing and 2 step texturing by micro blaster are compared. Reflectance of 1 step and 2 step texturing are measured 28.7% and 25.5%, respectively. The reflectance of 2 step texturing sample is lower about 3.2% than 1 step textured sample.

• PNF and Movement
• /
• v.1 no.1
• /
• pp.33-41
• /
• 2003

Objectives : The purpose of this study was to describe and compare the temporo-spatial gait characteristics of healthy young people with those of healthy elderly people. Methods: The data were collected by 40 volunteers. 20 subjects were between 20 and 31 years of age, and 20 subjects were between 65 and 84 years of age. Temporal and spatial parameters of gait were analysed for using the computerized GAITRite system. Results : The system integrates specific components of locomotion to provide a single, numerical representation of gait, the Functional Ambulation Performance score. Differences in gait characteristics between the two groups were examined using a correlated t-test(p<.05). Significant differences were observed between the groups for step length, step/extremity ratio and velocity. Young people demonstrated a significantly larger velocity, step length and step/extremity ratio than the elderly people. Conclusions: These results indicate that the GAITRite system can be useful in detecting footfall patterns and selected time and distance measurements of young and older persons. Additionaly, differences in walking velocity, step length and step/extremity ratio between old and young people may have influenced the gait characteristics measured.

• Proceedings of the KIEE Conference
• /
• 2006.07c
• /
• pp.1424-1425
• /
• 2006

A four-step rapid thermal annealing (RTA) process is proposed in order to improve the throughput and stabilize the process, compared to the six-step RTA process. Effects of annealing on the properties of a structure mode of CMOS process in both cases were investigated. The implanted dopant(As, $BF_2$ and Ti/TiN) movement in silicon during different rapid thermal annealing conditions was studied using secondary ion mass spectroscopy (SIMS) technique. These results show that the four-step RTA process significantly improves time effect and throughput (15%) by the condition of ramping up compared to the six-step RTA process.

• Transactions of Materials Processing
• /
• v.20 no.5
• /
• pp.357-361
• /
• 2011

A beryllium copper alloy(C1720) sheet was stretch-drawn using different processes. A hemispherical punch was first used and the forming behavior was examined. Then, cylindrical cups with a hemispherical head were produced by either one-step drawing or two-step forming(sequential stretch forming-drawing). The one-step drawing showed the better formability than two-step forming. However, the two-step forming was the superior process in terms of attaining shape accuracy.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.15 no.2
• /
• pp.23-29
• /
• 2015

The baby-step giant-step algorithm seeks b in a discrete logarithm problem when a,c,p of $a^b{\equiv}c$(mod p) are already given. It does so by dividing p by m block of $m={\lceil}{\sqrt{p}}{\rceil}$ length and letting one giant walk straight toward $a^0$ with constant m strides in search for b. In this paper, I basically reduce $m={\lceil}{\sqrt{p}}{\rceil}$ to p/l, $a^l$ > p and replace a giant with an adult who is designed to walk straight with constant l strides. I also extend the algorithm to allow $2^k$ adults to walk simultaneously. As a consequence, the proposed algorithm quarters the execution time of the basic adult-walk method when applied to $2^k$, (k=2) in the range of $1{\leq}b{\leq}p-1$. In conclusion, the proposed algorithm greatly shorten the step number of baby-step giant-step.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2008.10a
• /
• pp.91-93
• /
• 2008

The organic field-effect transistors with step-edge structure were fabricated. Source and drain electrodes were obliquely deposited by vacuum evaporation. The step-edge of the gate electrode serve as a shadow mask, and the short channel is formed at the step-edge. The excellent device performances were obtained.

• Proceedings of the KIEE Conference
• /
• 1993.07b
• /
• pp.977-980
• /
• 1993

The technique to design high performance small motors has been based on experimental data, which results from lots of cost, experience and time in manufacturing. Recently, as high-performance computer appears, many engineers use numerical methods to design and analyze electric machine. Since, the step motor which has very small air gap(0.02-0.05mm) is different from other electric machine in its structure. The shape of rotor teeth and stator teeth influence seriously on the torque characteristics. And it is operated over magnetic saturation point. Therefore, the design of step motor needs to solve nonlinear problem and to calculate magnetic field precisely. In this paper, we solve nonlinear problem by employing Finite Element Method and obtain torque-displacement characteristics for the design of step motor. We also manufacture VR step motor according to the obtained results, and measure some torque characteristics. Through comparing calculated results with experimental results, it is verified that FEM is very useful to design step motor, and the motor designed by our technique is improved in its step accuracy.