• Macromolecular Research
• /
• 제10권4호
• /
• pp.194-203
• /
• 2002

In resin infusion process(RIP), the fiber and the resin are in contact with each other for an impregnation step and often results in flow-induced defects such as poor fiber wetting and void formation. Resin flow characteristics in transverse direction and process modeling for woven fabric were studied, and the process modeling was applied to the manufacturing of hybrid composite materials. This study also considered the compressibility of woven fabrics in a series of compression force, and it was fitted well to an elastic model equation. Void formation was varied with the processing conditions in the stage of manufacturing composites using RIP. It was concluded from this study that proper combination of pressure build-up and dynamic heating condition makes important factor for flow-induced composite processing.

• 미생물학회지
• /
• 제11권3호
• /
• pp.129-133
• /
• 1973

The authors have investigated about the microbial contamination of goods which is a criterion of hygienic control. Conducting on investigation, a special attention has been paid on the rate of microbial contamination in the goods, especially in manufacturing process of the softdrink. The authors also made an experiment on total microbes which is the criterion of contamination in each step of the process and in raw materials together with materials to be used for subdividing. Results obtained were as follows : 1) The orgin of microbial contamination was found in bottle cap and in tap water, that is, there appeared 9 colony per ml in bottle cap and 31-74 colony per ml in tap water, respectively. 2) It was found that microbial contamination are 4 colony per ml in average through year. However, it appeared 1 colony per ml in winter and 8 colony per ml in summer. 3) Coliform groups are not detected in goods through a year. 4) There was no variation in number of total microbes after ion exchange resin passage in purification process of tap water. 5) The number of microbes in goods are decreased when the raw materials are treated in high temperature short time (HTST) sterilization.

• 전자공학회논문지A
• /
• 제30A권4호
• /
• pp.1-10
• /
• 1993

This paper presents the designing/manufacturing scheme of the diplexer for satellite transponder which is composed of 2-channel bandpass filters, coupled with E-plane T-junction, having symmetrical waveguide E-plane step discontinuity structures. The 2-channel bandpass filters of the diplexer are designed by the scheme of connecting ${\lambda}_{g}$/2 shunt stub to the waveguide E-plane, playing the role of heat sinks without attaching a special heat sinks and to give the profitable productivity and allow the low-cost manufacturing at mass production, tuning screws are eliminated which have been used to compensate the operating characteristics of manufactured filters. The 2 channel bandpass filters of manufactured 14/12 GHz diplexer for domestic Ku-band satellite transponder have the return loss of 25 dB, insertion loss of 0.3 dB in passband, and below-50 dB of stopband characteristics (T$_{x}$ : f$_{o}{\pm}$250 MHz, R$_{x}$ : f$_{o}{\pm}$220 MHz) at room temperature.

• 한국기계가공학회지
• /
• 제5권3호
• /
• pp.92-98
• /
• 2006

In this study, the behavior characteristics of a hydrostatic thrust bearing used in hydraulic equipment was analyzed using a commercial finite element program, ADINA. The solid domain was modeled with the fluid domain simultaneously to solve the fully coupled problem, because this is a problem where a fully coupled analysis is needed in order to model the fluid-structure interaction(FSI). The results such as bearing deformation, stress, film thickness and lifting bearing force were obtained through FSI analysis, and then they were compared with the results calculated from the classical method, a single step sequential analysis. It was found that the result difference between two analyses was increased according to the injection pressure. Therefore, in case of high pressure loading, it is desirable to conduct the FSI analysis to examine the deformation characteristics of a hydrostatic slipper bearing.

• 한국기계가공학회지
• /
• 제8권3호
• /
• pp.38-45
• /
• 2009

Recently, LCD Backlight Unit is being replaced from cold cathode fluorescent lamp(CCFL) to external electrode fluorescent lamp(EEFL) because the EEFL has high energy efficiency and long life. Also, it can reduce energy consumption and weight. So far, external electrode ring for EEFL is produced by sheet metal press forming process. Therefore it had low precision and much material loss. To solve these problems, Multi-Forming process that has five step forming process was invented. However, low productivity is another barrier. Product speed that is controlled by the rotational speed cannot be increased due to the unsatisfied design specification. The reason is that the gap between rolled two edge parts of the sheet plate is tightly inspected. Regarding this factor, the understanding of forming behavior to each process is inevitable. This paper describes the CAE analysis of the multi-forming process by PAM-STAMP.

• 한국생산제조학회지
• /
• 제21권1호
• /
• pp.156-160
• /
• 2012

Recently WCDMA signal transmission technology by large output microwave antenna have showed reduction of human resources and operating expense. But the existing antenna brackets cost is very expensive also its structure and functions are complicated. Unit brackets, suspending some sensors, subjected to acceleration loads, often fail due to self-vibration. To prevent such failures, it is necessary to understand the fatigue failure mode and to evaluate the fatigue life using tests or analysis techniques. The objective of this study is to develop the component test specifications, which are applicable to predict fatigue life at initial product design step, for unit brackets using vibration fatigue technique. So its application is limited to installation and management. In this project, we studied about more convenient bracket for microwave antennas through improvement on the existing antenna bracket's shortcoming and could develop an improved universal antenna bracket system for simple installation and application.

• 한국생산제조학회지
• /
• 제19권4호
• /
• pp.455-461
• /
• 2010

Automated magnetic abrasive polishing which can be applied after machining of the mold on a machine tool without unloading is very effective for finishing a complicated injection mold surface. This study aims to realize one step polishing of free form surface with the same machine tool. For this purpose, magnetic flux density according to the change of curvature radii was simulated for selecting polishing conditions and experimental verification was performed with a complicated mold of aluminum alloy. As a result, it was seen by the simulation that the magnetic flux density at a gradual curvature of the mold was higher than at a steep curvature and the higher magnetic flux density produced the better surface roughness in the experimentation. The deviation for the surface roughness of the mold decreased on the whole and the uniform mold surface was obtained after the automated magnetic abrasive polishing.

• 대한안전경영과학회지
• /
• 제9권2호
• /
• pp.171-181
• /
• 2007

Over ten years, 6sigma management is applied a lot in the part of indirect business as well as the manufacturing industry. But it has still been used restrictively the technique used on DMAIC that is a basic Roadmap of 6 sigma. This paper finds the improving skills that is used in the parts of manufacturing and indirect business and demonstrates their available scope with 6sigma projects. And this indicates which skills for improving are used valuable on each step of DMAIC with a systematic classification.

• Journal of Information Processing Systems
• /
• 제16권1호
• /
• pp.30-41
• /
• 2020

Lines and textures are natural properties of the surface of natural objects, and their images can be sparsely represented in suitable frames such as wavelets, curvelets and wave atoms. Based on characteristics that the curvelets framework is good at expressing the line feature and wavesat is good at representing texture features, we propose a model for the weighted sparsity constraints of the two frames. Furtherly, a multi-step iterative fast algorithm for solving the model is also proposed based on the split Bergman method. By introducing auxiliary variables and the Bergman distance, the original problem is transformed into an iterative solution of two simple sub-problems, which greatly reduces the computational complexity. Experiments using standard images show that the split-based Bergman iterative algorithm in hybrid domain defeats the traditional Wavelets framework or curvelets framework both in terms of timeliness and recovery accuracy, which demonstrates the validity of the model and algorithm in this paper.

• 한국기계가공학회지
• /
• 제20권2호
• /
• pp.72-79
• /
• 2021

The present paper aims to set forth a two-dimensional theory for the dynamics of plates that is valid over a large range of excitation. To construct a dynamic plate theory within the long-wavelength approximation, two dimensional-reduction procedures must be used for analyzing the low- and high-frequency behaviors under the dynamic variational-asymptotic method. Moreover, a separate and logically independent step for the short-wavelength regime is introduced into the present approach to avoid violation of the positive definiteness of the derived energy functional and to facilitate qualitative description of the three-dimensional dispersion curve in the short-wavelength regime. Two examples are presented to demonstrate the capabilities and accuracy of all of the formulas derived herein by using various dispersion curves through comparison with the three-dimensional finite element method.