• Journal of IKEEE
• /
• v.17 no.4
• /
• pp.537-543
• /
• 2013

This paper proposed a low EMI spread spectrum clock generator (SSCG) using discontinuous frequency modulation technique. The proposed SSCG is designed for triangular frequency modulation with high modulation depth. When the maximum time interval error (MTIE) of the SSCG is higher than given limit, the output frequency of SSCG is divided by two and used for reducing the time interval error (TIE). This discontinuous frequency modulation technique can effectively reduce the EMI within given limit. The simulated EMI of proposed SSCG was reduced by 18.5dB than that of conventional methods.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.47 no.10
• /
• pp.7-13
• /
• 2010

A compact phase interpolator (PI) based spread spectrum clock generator (SSCG) for electromagnetic interference (EMI) reduction is presented. The proposed SSCG utilizes a digitally controlled phase interpolation technique to achieve triangular frequency modulation with less design complexity and small power and area overhead. The novel SSCG can generate the system clock with a programmable center-spread spectrum range of up to +/- 2 % at 200 MHz, while maintaining the clock duty cycle ratio without distortions. The PI-based SSCG has been designed and evaluated in 0.18-um 1.8-V CMOS technology, which consumes about 5.0 mW at 200MHz and occupies a chip size of $0.092mm^2$ including a DLL.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.13 no.4
• /
• pp.282-290
• /
• 2013

This paper describes a spread spectrum clock generator (SSCG) circuit for DisplayPort 1.2 standard. A Hershey-Kiss modulation profile is generated by dual sigma-delta modulators. The structure generates various modulation slopes to shape a non-linear modulation profile. The proposed SSCG for DisplayPort 1.2 generates clock signals with 5000 ppm down spreading with a Hershey-Kiss modulation profile at three different clock frequencies, 540 MHz, 270 MHz and 162 MHz. The measured peak power reduction is about 15.6 dB at 540 MHz with the chip fabricated using a $0.13{\mu}m$ CMOS technology.

• Journal of IKEEE
• /
• v.15 no.1
• /
• pp.23-28
• /
• 2011

This paper describes design and implementation of a spread spectrum clock generator(SSCG). The proposed architecture generates the spread spectrum clock controlling a input voltage signal for VCDL(Voltage Controlled Delay Line). Spread charge pump is controlled by the SSC modulation logic block provides a control signal to VCDL through LPF in DLL. By using this architecture, chip area and power consumption can be reduced because it is not necessary additional circuit to control modulation rate. This circuit has been designed and fabricated using the UMC 0.25um CMOS technology. The chip occupies an area of 290${\times}$120um^2.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2009.06a
• /
• pp.17-17
• /
• 2009

Piezoelectric single crystals in the ternary MPB PMN-PZ-PT system with high $T_cs$ ($T_c$ > $200\sim300^{\circ}C$) and $E_cs$($E_c$>5~10 kV/cm) were fabricated by the cost-effective solid-state crystal growth (SSCG) technique. Chemically uniform PMN-PZT single crystals were successfully grown up to 60 mm by the SSCG method and their dielectric and piezoelectric properties characterized. Compared to Bridgman PMN-PT single crystals, the high $T_c/E_c$ PMN-PZT single crystals were found to exhibit a much wider usage range with respect to electric field as well as temperature, and thus become best candidates for medical transducers, actuators, and naval applications.

• IEIE Transactions on Smart Processing and Computing
• /
• v.3 no.6
• /
• pp.404-409
• /
• 2014

This paper presents a Spread Spectrum Clock Generator (SSCG) based on Relaxation oscillator using Up/Down Counter. The current is controlled by a counter and the spread spectrum of the Relaxation Oscillator. A Relaxation Oscillator with temperature compensation using the BGR and ADC is presented. The current to determine the frequency of the Relaxation Oscillator can be controlled. The output frequency of the temperature can be compensated by adjusting the current according to the temperature using the code that is the output from the ADC and BGR. EMI Reduction of SSCG is 11 dB, and Spread down frequency is 150 kHz. The current consumption is $600{\mu}A$ from 5V and the operating frequency is from 2.3 MHz to 5.75 MHz. The rate of change of the output frequency with temperature was approximately ${\pm}1%$. The SSCG is fabricated in a 0.35um CMOS process with active area $250um{\times}440um$.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.46 no.7
• /
• pp.68-73
• /
• 2009

This paper describes design and implementation of a spread spectrum clock generator (SSCG) for the DisplayPort. The proposed architecture generates the spread spectrum clock using a sigma-delta fractional-N PLL. The SSCG uses a digital End order MASH 1-1 sigma-delta modulator and a 9bit Up/Dn counter. By using MASH 1-1 sigma-delta modulator, complexity of circuit and chip area can be reduced. The advantage of sigma-delta modulator is the better control over modulation frequency and spread ratio. The SSCG generates dual clock rates which are 270MHz and 162MHz with 0.25% down-spreading and triangular waveform frequency modulation of 33kHz. The peak power reduction is 11.1dBm at 270MHz. The circuit has been designed and fabricated using in 0.18$\mu$m CMOS technology. The chip occupies 0.620mm$\times$0.780mm. The measurement results show that the fabricated chip satisfies the DispalyPort standard.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.16 no.4
• /
• pp.425-435
• /
• 2016

This paper describes a spread-spectrum clock generation method by utilizing a ${\Delta}{\Sigma}$ digital PLL (DPLL) which is solely based on binary phase detection and does not require a linear time-to-digital converter (TDC) or other linear digital-to-time converter (DTC) circuitry. A 1-bit high-order ${\Delta}{\Sigma}$ modulator and a hybrid finite-impulse response (FIR) filter are employed to mitigate the phase-folding problem caused by the nonlinearity of the bang-bang phase detector (BBPD). The ${\Delta}{\Sigma}$ DPLL employs a two-point modulation technique to further enhance linearity at the turning point of a triangular modulation profile. We also show that the two-point modulation is useful for the BBPLL to improve the spread-spectrum performance by suppressing the frequency deviation at the input of the BBPD, thus reducing the peak phase deviation. Based on the proposed architecture, a 3.2 GHz spread-spectrum clock generator (SSCG) is implemented in 65 nm CMOS. Experimental results show that the proposed SSCG achieves peak power reductions of 18.5 dB and 11 dB with 10 kHz and 100 kHz resolution bandwidths respectively, consuming 6.34 mW from a 1 V supply.

• Korean Journal of Materials Research
• /
• v.31 no.9
• /
• pp.488-495
• /
• 2021

Solid state grain growth (SSCG) is a method of growing large single crystals from seed single crystals by abnormal grain growth in a small-grained matrix. During grain growth, pores are often trapped in the matrix and remain in single crystals. Aerosol deposition (AD) is a method of manufacturing films with almost full density from nano grains by causing high energy collision between substrates and ceramic powders. AD and SSCG are used to grow single crystals with few pores. BaTiO₃ films are coated on (100) SrTiO₃ seeds by AD. To generate grain growth, BaTiO₃ films are heated to 1,300 ℃ and held for 10 h, and entire films are grown as single crystals. The condition of grain growth driving force is ∆G_max < ∆G_c ≤ ∆G_seed. On the other hand, the condition of grain growth driving force in BaTiO₃ AD films heat-treated at 1,100 and 1,200 ℃ is ∆G_c < ∆G_max, and single crystals are not grown.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.27 no.12
• /
• pp.1097-1104
• /
• 2016

The infrared camera is difficult to satisfy the RE-102 specification of Mil-Std-461. Especially, in the case of UAV electronics, shielded cable is not used, so it is difficult to meet the electromagnetic compatibility standard. In the RE-102 test of the IR camera for UAV, radiated noise exceeding 30 dBuV/m was observed in the range of 50 MHz to 200 MHz. As a result of pcb em scan, peak noise which caused by the harmonic frequency of the digital control signal clock was observed. Radiated noise was reduced by up to 22.9 dBuV/m by applying the spread spectrum clock generator(SSCG) with 3 % down spreading method to the camera control clock.