• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.28 no.3C
• /
• pp.215-223
• /
• 2003

Turbo codes are selected as FEC(Forward error correction) codes with convolution code in 3GFP(3rd generation partnership project) and 3GPP2 standard of IMT2000. Especially, l/3 turbo code with K=4 is employed for 3GPP standard. In this paper, we proposed a hardware structure of a turbo decoder and denveloped the decoder for 3GPP standard turbo code. For its efficient operation, we design a SOVA decoder by employing a register exchange decoding block and new path metric normalization block as a SISO constituent decoder. In addition, we estimate its performance under MATLAB 6.0 and designed the turbo decoder including control block, input control buffer, SOVA constituent decoder with VHDL. Finally, we synthesized the developed turbo decoder under Synopsys FPGA Express and verified it with ALTERA EPF200SRC240-3 FPGA device.

• The Transactions of the Korean Institute of Electrical Engineers C
• /
• v.49 no.3
• /
• pp.186-195
• /
• 2000

In this paper, partial discharge (PD) measurement was performed to evaluate the quality of the cable joint and termination constructions. The resistive coupling technique for PD detection using resistivity of semiconducting layer of the cable in the accessories, such as joints and terminations. With high frequency PD (HEPD) measurement, an excellent sensitivity below 20pC could be achieved under unshielded condition. The localization of the defects in the accessories could be identified. During heating cycle, PDs were monitored and analyzed. At that time, the PDs were dependent on the temperature of the heating cycle and showed cyclic behaviors, which were attributed to local delamination of the interfaces, between epoxy unit and stress relief cone(SRC) and between SRC and cable, due to the difference of thermal expansion. As a conclusion, HFPD measurement technique was proven to be an effective diagnostic method for qualification of extra high voltage (EHV) cable accessories. With this technique, the optimal design of the components of the accessories could be verified not only in an early stage but also under operating condition. This technique would result in the improvement of the reliability of the EHV cable accessories.

• Proceedings of the Korean Information Science Society Conference
• /
• 2010.11a
• /
• pp.127-128
• /
• 2010

본 논문에서는 CCTV 감시 영상에서 취득한 얼굴 이미지를 이용하여, 범죄자 감시목록에 등록된 범죄 용의자를 탐지 식별하는 시스템을 설계 및 구현하였다. 특히 본 논문에서 제안한 SVDD와 SRC를 혼합한 계층적 구조의 범죄 용의자 식별 모듈은 다음과 같은 특성을 갖는다: 1) 먼저 SVDD를 이용하여 범죄 용의자만을 빠르게 인식함으로써, 일반인에 대한 불필요한 범죄자 식별 연산을 수행하지 않는다; 2) 다양한 식별 성능을 저해하는 환경에서도 이미 강인한 성능이 검증된 SRC를 범죄 용의자 식별과정에 적용함으로써 안정적이고 정확한 식별 시스템을 보장한다; 3) 동일 생체 특정의 반복적 사용을 통한 다수결 투표전략을 취함으로써 시스템의 신뢰도를 보장한다; 4) 점증적 갱신의 학습 능력으로 인하여 범죄 용의자 감시목록 데이터베이스의 변화에도 능동적으로 적응한다 실제 KUFD(Korea University Face Database)를 자체 제작하고 캠퍼스 내에서 CCTV 환경의 얼굴 인식 기반 범죄 용의자 탐지 및 식별 시스템 환경을 모의 구축하여 실험적으로 제안된 시스템의 성능을 검증한다.

• Computers and Concrete
• /
• v.26 no.6
• /
• pp.515-531
• /
• 2020

Due to the construction difficulties of steel reinforced concrete (SRC), a new composite structure of steel and steel fiber reinforced concrete (SSFRC) is proposed for solving construction problems of SRC. This paper aims to investigate the bond properties and composition of interfacial bond stress between steel and steel fiber reinforced concrete. Considering the design parameters of section type, steel fiber ratio, interface embedded length and concrete cover thickness, a total of 36 specimens were fabricated. The bond properties of specimens were studied, and three different methods of calculating interfacial bond stress were analyzed. The results show: relative slip first occurs at the free end; Bearing capacity of specimens increases with the increase of interface embedded length. While the larger interface embedded length is, the smaller the average bond strength is. The average bond strength increases with the increase of concrete cover thickness and steel fiber ratio. And calculation method 3 proposed in this paper can not only reasonably explain the hardening stage after the loading end curve yielding, but also can be applied to steel reinforced high-strength concrete (SRHC) and steel reinforced recycled coarse aggregate concrete (SRRAC).

• Asia Marketing Journal
• /
• v.7 no.3
• /
• pp.105-119
• /
• 2005

Samsung Fire & Marine Insurance Co., Ltd. launched 'Samsung Super Insurance Package', an insurance policy combining household's property & casualty insurance policies, except insurance with savings and pension insurance, into one for the first time in Korea. The product was developed to tackle challenges and threats from environmental changes, whose success owes to an excellent marketing strategies like adopting MCS system which is coined to support sales force activities, and building SRC(Samsung Risk Consultant), the organization dedicated to the sales of the product. The case shows how Samsung Fire & Marine Insurance Co., Ltd. developed and successfully marketed the combined insurance policy for the first time in Korea identifying the key success factors and discusses its business implications and future challenges.

• Proceedings of the Zoological Society Korea Conference
• /
• 2001.10a
• /
• pp.190.1-190
• /
• 2001

No Abstract, See Full Text

• Nuclear Engineering and Technology
• /
• v.18 no.3
• /
• pp.209-217
• /
• 1986

The inlet coolant temperature reduction technique has been used to extend the load follow operation further in the end-of-cycle-life(EOL). In order to simulate the technique and calculate the nuclear characteristics of a PWR core according to the load follow operation, the three dimensional computing system has been established. The analysis was performed in both MINB and SPINR modes of typical 12-3-6-3 locad follow operation for the EOL of KNU-1 plant. Moreover, the capability of return-to-power has been also tested for those two modes with the system analysis by the RETRAN-02 code. The results show that it has no difficulty to extend the load follow operation further in the EOL by applying the inlet coolant temprature reduction, and also the spinning reserve capacity(SRC) increases by 13% in MINB mode and 14% in SPINR mode Bore that used by control rods only, for 14$^{\circ}$ F drop in the inlet temperature.

• Journal of Korean Society of Steel Construction
• /
• v.13 no.4
• /
• pp.419-431
• /
• 2001

This study was to investigate structural behavior of composite structure beams composed of end-RC. center-Steel according to respective reinforcing method for connection zone composed of different materials (SRC) while attaching main bars on steel-flange by welding. The main reinforcing methods are as follows ; non-reinforcing, vertical shear reinforcing (type-stirrup), inclined reinforcing(type-x), horizontal reinforcing(type-web, 0.3L), double horizontal reinforcing (type-web, 0.3L), vertical reinforcing (type-flange, 0.3L). Consequently, It showed little difference in structural properties like ductility and strength according to the attaching method of main bars. For Maximizing the structural properties of composite beam, the most effective methods were vertical reinforcing one and double horizontal reinforcing one.

• Journal of Korean Society of Steel Construction
• /
• v.29 no.2
• /
• pp.135-145
• /
• 2017

This study is a secondary study that is a cyclic seismic test of High depth hybrid composite beam and column connection after the primary bending strength test of a high depth Hybrid composite beam. Total of 3 seismic test specimens were prepared to cyclic test. The bracket and beam web spliced by high strength bolt and the bracket and beam upper flange was spliced by welding. Test results showed that the seismic strength was higher than the plastic moment($M_p$) in the positive negative moment section, the requirement of composite intermediate moment frame wes satisfied. Therefore, the requirement of intermediate moment frame can be secured by applying the details of connection of this study results.

• Proceedings of the Korean Society of Developmental Biology Conference
• /
• 2003.10a
• /
• pp.117-117
• /
• 2003

체외에서 한우 난포란의 감수분열과 배발달 능력의 획득에는 단백질 합성이 수반되어야 한다. 그러나 이러한 변화와 관련된 연구 보고는 거의 전무한 실정이다. 본 실험은 난자의 핵성숙과 관련된 세포질내 단백질 변화를 파악하기 위하여, 체외성숙 시간에 다른 배발달율과 세포질내 단백질을 비교하여 배발달능력 획득과 관련 있는 단백질을 규명하고자 실시하였다. 한우 난소에서 2-8mm의 가시난포로부터 난포란을 회수하였다. 회수된 난포란은 10% FBS와 호르몬이 첨가된 TCM199 용액에서 18시간 또는 24시간 체외성숙을 실시하였다. 난자 세포질내 단백질 변화는 2D gel electrophoresis를 이용하였고, 유의적인 변화를 나타낸 spot은 peptide mass fingerprinting을 통하여 단백질 동정을 실시하였다. 체외수정은 fer-TALP 용액을, 체외배양은 CR1aa 용액을 배양 3일째까지는 0.3% BSA, 그 이후에는 10% FBS와 난관상피세포를 첨가하여 사용하였다. 통계분석은 t-test를 이용하였다. 난자의 세포질에 대한 이차원전기영동 결과 29개의 단백질 spot들을 확인하였다. 한편 체외성숙 18시간째에 PB가 출현된 난자는 PB가 출현되지 않은 난자에 비하여 15개의 spot에서 유의적인 변화를 나타냈다. 이들 중 4개의 단백질 spot은 낮았고, 11개 spot의 수준은 높은 경향이었다. 체외성숙 18시간째와 24시간째의 배발달율을 조사한 결과 18시간째에서 유의적으로 높은 배반포 발달율을 나타냈다. 그리고 체외성숙 18시간과 24시간째 난자의 세포질내 단백질 spot들의 변화를 비교한 결과 PB가 출현된 난자 세포질에서 단백질의 변화와 유사한 경향이었다. 그러나 2개의 단백질 spot은 상반된 경향을 나타냈다. 따라서 본 실험에서 난자의 핵성숙과 관련 있는 15개의 spot을 확인하였고, 이들 단백질 spot중에서 2개가 배발달 능력과 관련이 있을 것으로 사료된다.보다는 육질등급에 많은 영향을 받는 것으로 판단된다. 한편 육질 1등급에서 배발달율이 낮은 이유는 육질 향상을 목적으로 암소를 비육 하는 경우 발생하는 번식장애와 밀접한 관계가 있는 것으로 사료된다.각각 가장 높았다. 배양 8일째 배반포의 세포수에 있어서 총세포수와 TE 세포수는 차이가 없었으나, ICM 세포수가 l0mg 첨가군에서 가장 높았다. 본 실험 결과에서 체외성숙 배지에 NEAA와 EAA 첨가가 배발달율에는 효과가 없었지만, 첨가농도의 증가에 따라 ICM 세포수가 증가하였다. 한편 체외성숙 배지에 LAH 첨가는 첨가 농도가 높을수록 배발달율은 낮았지만 ICM 세포수는 증가하였다.에 Csk가 관여하고 있음을 알 수 있다. 결론적으로 성적 성숙에 따른 생쥐 정소 내 Src-Csk loop의 발현과 Src kinase 활성의 변동은 정소 내 간충조직, 세정관 상피의 증식 및 기능적 분화 과정을 매개하는 생리적 활성분자 수용체 하위의 신호전달 과정에 Src-Csk loop에 의한 조절가능성을 확인할 수 있었다.rugrene의 향기성분이 주요 성분군으로 확인되었다. 2. 생강나무에서 생강의 향기를 발산하는 성분으로는 $\beta$-myrcene, o-terpinolene, phellandrone, ι-limonene, $\beta$-eudesmol, $\delta$-cadinone, elemol, trans-caryophyllene으로 동정되었으며 그 중에서도 phellandrene, $\beta$-eudesmol이 주된 역할을 하는 성분으로 확인하였다. 유의적인 관련성이 나타났고, 복부 비만의 지표인 허리엉덩이둘레비는 GPT, alkaline phosphatase, 공복시 혈당 및 MCV 등 다양한 건강지표와 관련성을 나타내어 향후 비만에 있어 다양한 혈액 성상의 변화 및 역할규명에 대한 연구가 이루어져야 할 것으로 본다.hat