• Journal of Korea Foundry Society
• /
• v.22 no.1
• /
• pp.17-25
• /
• 2002

Recently, many studies have been carried out to process on the purpose of lightness in a transport parts because of the saving energy, the environmental problem. The cast-forging process can be expected to lower costs without decreasing the mechanical properties. So, the finest microstructure is needed to get for applying the cast-forging process with Al-Si alloy because the microstructure affects to the cast-forging process. For refinement treatment of eutectic Si and Al solid-solution phase, Sr and TiB were added in Al-Si alloys. The finest microstructure could be observed when 0.075 wt.%Sr and 0.1 wt.%TiB were added respectively. In this case, tensile strength and elongation much more increased than as casting. After high temperature deformation simulation test with grain refinement specimens was carried out, about 70N per unit $area(mm^2)$ of specimen was confirmed. After hot forging, tensile strength and elongation were increased. It was considered because casting defect was removed by compressive working.

• Journal of Korea Foundry Society
• /
• v.22 no.1
• /
• pp.26-34
• /
• 2002

For application of cast-forging process with Al-Si alloys, casting experiments are carried out by adding Sr and TiB to Al-Si alloys for grain refinement treatment. We experimented on the mechanical properties according to microstructural changes, forging ability test and also investigated the mechanical properties after forging. The finest microstructure could be observed respectively when 0.05 wt.%Sr and 0.1 wt.%TiB were added. In this case, tensile strength and elongation increased much more than as casting. After high temperature deformation simulation test with grain refinement specimens was carried out, about 60N per unit $area(mm^2)$ of specimen was confirmed. After hot forging, tensile strength and elongation were increased. It was considered that casting defect was removed by compressive working.

• Electrical & Electronic Materials
• /
• v.7 no.4
• /
• pp.281-288
• /
• 1994

According to spread volume of B(BiPbCuO) layer, composition ratio and each stage of sintering process, we studied stability of high Tc superconductor phase and generation and growth movement of superconducting phase. The dual layer composed of SrCaCuO and BiPbCuO compound were prepared to develop the Bi-2223 superconductor[108K] through interaction and diffusion during sintering process. The dual layer samples were sintered at 830.deg. C for 0-210 hours. From the result, the optimum conditions were : spread volume(A:B=1:0.6), sintering time(210h) and composition ratio(A:S $r_{2}$C $a_{2}$C $u_{2}$- $O_{x}$, B:B $i_{1.9}$P $b_{0.5}$C $u_{3}$ $O_{y}$) at 830.deg. C.. C.C.C.

• Proceedings of the Korean Magnestics Society Conference
• /
• 2002.12a
• /
• pp.86-87
• /
• 2002

Fe과 Mo이 교대로 정렬해 있는 이중 페로브스카이트 구조를 갖는 $A_{2-x}$FeMo $O_{6}$(A=Ca, Sr, Ba) 화합물들은 망간 산화물들에 비해 높은 $T_{c}$ (310-420K)의 준강자성 상태를 갖는다.$^{1.3}$ 이 화합물들은 F $e^{3+}$ (S=5/2) 와 M $o^{5+}$(S=1/2) 스핀들 사이의 커다란 반강자성 상호작용으로 이론적으로 4$\mu$$_{B}$/f.u.의 $M_{s}$ 값을 갖는다. A-site의 평균 이온 반경( $r_{A}$)이 증가함에 따라 이 화합물들의 결정구조는 Monoclinic(A=Ca)에서 Tetragonal(Sr)과 Cubic(Ba)으로 점진적으로 변화한다.$^3$(중략)(중략)략)략)

• Journal of Nuclear Fuel Cycle and Waste Technology
• /
• v.1 no.1
• /
• pp.49-55
• /
• 2013

To characterize quantitatively the transport of $^{99}Tc$ and the global fallout ($^{137}Cs$, $^{90}Sr$, and $^{239+240}Pu$) for soils in Korea, the transport parameters of a convective-dispersion model, apparent migration velocity, and apparent dispersion coefficient were estimated from the vertical depth profiles of the radionuclides in soils. The vertical profiles of $^{99}Tc$ were measured from a pot experiment for paddy soil that had been sampled from a rice-field around the Gyeongju radioactive waste repository in Korea, and the vertical depth distributions of the global fallout $^{137}Cs$, $^{90}Sr$, and $^{239+240}Pu$ were measured from the soil samples that were taken from local areas in Korea. The front edge of the $^{99}Tc$ profiles reached a depth of about 12 cm in 138 days, indicating a faster movement than the fallout radionuclides. A weak adsorption of $^{99}Tc$ on the soil particles by the formation of Tc(VII) and a high water infiltration velocity seemed to have controlled the migration of $^{99}Tc$. The apparent migration velocity and dispersion coefficient of $^{99}Tc$ for the disturbed paddy soil were 2.88 cm/y and 6.3 $cm^2/y$, respectively. The majority of the global fallout $^{137}Cs$, $^{90}Sr$, and $^{239+240}Pu$ were found in the top 20 cm of the soils even after a transport of about 30 years. The transport parameters for the global fallout radionuclides were 0.01-0.1cm/y ($^{137}Cs$), 0.09-0.13cm/y ($^{90}Sr$), and 0.09-0.18cm/y ($^{239+240}Pu$) for the apparent migration velocity: 0.21-1.09 $cm^2/y$ ($^{137}Cs$), 0.12-0.7$cm^2/y$ ($^{90}Sr$), and 0.09-0.36$cm^2/y$ ($^{239+240}Pu$) for the apparent dispersion coefficient.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.35 no.1
• /
• pp.24-31
• /
• 2022

This study investigated microstructures, crystal structures, polarization, dielectric and electromechanical properties of 0.76Bi_1/2Na_1/2TiO₃-0.24SrTiO₃ (BNT-24ST)-based piezoceramcs by adding Li₂CO₃ and B₂O₃ (LB) as sintering aids for low-temperature sintering. All samples were successfully synthesized using conventional solid-state reaction method and sintered at 950, 1,000, 1,050, 1,100 and 1,175℃ for 2 hours. Without LB, specimens required sintering temperatures over 1,175℃ for sufficient densification, while the addition of 0.10-mol LB decreased the sintering temperatures down to 950℃. The average grain size and dielectric properties of BNT-24ST-10LB ceramics were enhanced with increasing sintering temperature. We found that the low-temperature sintered BNT-24ST piezoceramics by adding LB showed the d₃₃*value of 402 pm/V at 4 kV/mm after sintering at 1,050℃, which was better than that of high-temperature fired specimens sintered at 1,175℃ without LB (242 pm/V). We believe that the results of this study promise a candidate for low-cost multilayer ceramic actuator applications.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.37 no.6
• /
• pp.583-590
• /
• 2013

Variable emittance radiators can be used in a thermal management system in space because their total emittance changes depending on the temperature of the system. When the temperature of the system decreased, the emittance also decreased so as to minimize the heat loss to the environment. In contrast, when the temperature of the system increased, the emittance also increased such that radiation cooling could occur. Thermochromic materials, whose emittance is a function of the temperature, are often used in variable emittance radiators because no additional parts are needed. In this study, we fabricated a variable-emittance coating by using a sol-gel method based on LSMO ($La_{1-x}Sr_xMnO_3$) and experimentally characterized the emittance change with respect to temperature. Furthermore, we also examined the stability of LSMO film in space environments by exposing it to extremely low pressure and temperature.

• Journal of the Mineralogical Society of Korea
• /
• v.27 no.1
• /
• pp.41-51
• /
• 2014

The four natural zeolites collected in Pohang and Gyeongju area, Kyungsangbuk-do, Korea, were characterized by XRD, XRF, DTA, TGA, and CEC analysis. The primary species of these zeolite are heulandite, modenite, illite, and illite in Kuryongpo (Ku), Pohang (Po), Yangbuk-A (Ya-A), and Yangbuk-B (Ya-B) samples. The XRF analysis showed that the four zeolites contain Si, Al, Na, K, Mg, Ca, and Fe. Cation exchange capacity of Kuryongpo (Ku) zeolite was the highest compared to other zeolites. The adsorption capacities of Cs and Sr in the four natural zeolites were compared at $25^{\circ}C$. On the basis of adsorption data Langmuir and Freundlich adsorption isotherm model were confirmed. The equilibrium process was descried well by Langmuir isotherm model. This study shows that Ya-A zeolite is the most efficient for the $Cs^+$ and $Sr^{2+}$ ion adsorption compared to the other natural zeolites.

• Korean Journal of Fisheries and Aquatic Sciences
• /
• v.14 no.4
• /
• pp.269-275
• /
• 1981

The fishing hooks were tested for breaking and unbending due to plastic deformation of the material. Study of tensile test is not complicated, but has not even worked out fully enough, especially when the test specimen is subjected to plastic deformation. The fishing hook is subjected to unbending stress and the critical section is a Point which is furthest from the line of action of the forces. The dynamic force of fish during jerks depends on their speed of movement and body weight, the kinetic energy corresponding to it and also on the rlastic displacement of the rigging which absorb the energy. Six kinds of hook were tested by the dynamometer under tensile speed 290mm/min (subscript s) and 780mm/min (subscript f). According to their results, the breaking load(B: kg) can be induced with the formula $B={\alpha}wd^2+\beta$ where w(mm) is the distance between the barb base and the lower shank and d(mm) is diameter. The coefficients of the formula for the round hooks(R) and the angular hooks(A) are approximately as follows: $$R:\;\alpha_{s}=0.5,\;\beta_{s}=1.6,\;\alpha_{f}=0.4,\;\beta_{f}=1.4$$ $$A:\;\alpha_{s}=1.1,\;\beta_{s}=2.0,\;\alpha_{f}=1.0,\;\beta_{f}=0.9$$ The ratio of $B_{f}\;to\;B_{s}$ is corresponding to 0.8. The ratio of deformation(X) that is moved distance of barb base at break to the distance(H) between head base and barb base is about $50\%$. Further study should be carried out on the subject of impact and fatigue test under the same condition which is exerted force by the hooked fish.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.8 no.7
• /
• pp.1429-1435
• /
• 2004

In this work, high performance broadband amplifier MMIC including all the matching and biasing components, and electrostatic discharge (ESD) protection circuit was developed for K/Ka band applications. Therefore, external biasing or matching components were not required for the operation of the MMIC. STO (SrTiO3) capacitors were employed to integrate the DC biasing components on the MMIC, and miniaturized LC parallel ESD protection circuit was integrated on MMIC, which increased ESD breakdown voltage from 10 to 300 V. A pre-matching technique and RC parallel circuit were used for the broadband design of the amplifier MMIC. The amplifier MMIC exhibited good RF performances and good stability in a wide frequency range. The chip size of the MMICs was $1.7{\pm}0.8$ mm2.